motorcycle lift

Поділитися
Вставка
  • Опубліковано 22 гру 2024

КОМЕНТАРІ • 413

  • @webbysbass
    @webbysbass 6 років тому +3

    Hello Emil I just ran into this BIKE Lift video you put on here five years ago,I can't believe I just now found this.I've been pickin up parts for a couple of years now to build a Table and you have it,this is great.I have a Sears bike jack but my brother Chief and I have been buyin up old BSA 650's that have been settin to damn long in out buildings ,garages old barns,all the bikes been apart for years and not everything is ever all there,but that's what we want.We have been mocking some things up to get a idea.We got us a 65 650 fresh rebuild we set in a hardtail Bobber frame tube front short bars long pipes and a ass buster of a seat.And built it on a small 18"by 28" heavy power lift that is scary got ta set them on the frame no way to tie down,tires hanging over in the way.We've picked up three more getting to the point of wanting to get going again got two more Engines done ready to go .Now we have a couple more hardtail's to build but we got us a few old Girder springer front ends and picked us up a old I think 1930s stock harley springer ya know the one's they use to cut the early ford front axle radius rods off and use them to stretch the forks.We want to build a couple of springer hardtail choppers Old School stile and a couple more Bobbers but it's time to take the ram from an old down rigger cyl from a back hoe, pump and table and mate them to what you have designed.I was hoping thatI could please get the info and or some prints on your lift design.This would help a couple old bikers from bending over so much I'm now 64 and I was a heavy EQUP. mechanic form the early 70s and things do not bend the way they use to ya know what I mean .If you could in your heart take the time to send me anything you have to webbysbass@yahoo.com my knees thank you as do I. We have most of our Iron just got to get out the ol Miller Mig and get it done.Again if you could do this for us we would thank you every time a bike goes on it to build. This old Gray Beard thanks you for any and all the help .

  • @benssben6978
    @benssben6978 2 роки тому +3

    Great job emil thanks for video.
    Do you have plans and dimension?
    Thank you

  • @CreativeEGO-oq9vt
    @CreativeEGO-oq9vt 10 місяців тому

    Thank you for the video; it provided me with a good foundation. However, I would like some advice on designing a mobile 3T scissor lift, specifically modeled after the EE-TS6600. It has two hydraulic cylinders. Would it not be better to use standard cylinder components available online? I would really appreciate it if you could draft the design of a mobile scissor lift. Could you please help me with this?

  • @mrmdasmattathil2048
    @mrmdasmattathil2048 3 роки тому

    Nice work indeed💐 . Can you please tell me which app or programm u r using to create video like this..?

  • @Jason.Granados
    @Jason.Granados 2 роки тому

    Hi there! Great Build! Can I please get a copy of the build?

  • @andilast333
    @andilast333 7 місяців тому

    to make it like that. What bearing do the wheel rails use?

  • @pincho9792
    @pincho9792 11 місяців тому

    hi emil,can u send me the design and what u have more about this ptoject?
    thank you

  • @danielciocirlan7965
    @danielciocirlan7965 4 роки тому

    In which program is maked this project ,please???!

  • @bitmumia0
    @bitmumia0 4 роки тому

    Awesome video.
    Can somebody send me the the plans where the size can be found?

  • @srajangupta6837
    @srajangupta6837 4 роки тому

    Awasome 👍👍🔥....can you guide me how to preform this part wise motion assembly....?

  • @jaba3096
    @jaba3096 4 роки тому

    which software this sir

  • @mauriziozito1803
    @mauriziozito1803 2 роки тому

    Congratulations, great job.
    Can you send me a copy of the build plane, please ?
    Thanks You.

  • @prajaktam5118
    @prajaktam5118 2 роки тому

    Can you please tell what is the red part in the centre called?

  • @diegolanzo
    @diegolanzo 4 місяці тому

    Ciao emil, bellissimo lavoro, gentilmente mi potresti mandare le misure?
    Ti ringrazio

  • @leonardorojas1781
    @leonardorojas1781 4 роки тому

    How does the mechanism gets actuated? 😦

  • @flyingdog1498
    @flyingdog1498 5 років тому

    So tell me, how do you get to bottle jack to operate the lift?

  • @laklabealibarra896
    @laklabealibarra896 Рік тому

    excelente trabajo. Serias tan amable de enviarme los planos?

  • @mihirajgaonkar4411
    @mihirajgaonkar4411 4 роки тому

    Hey , on which software are these mechanisms played ?

    • @emillyudmilov
      @emillyudmilov  4 роки тому

      It was drawn on SolidWorks
      unfortunately these files are lost
      now it is in Parasolid and STEP files
      The 3D model can be downloaded from GrabCad
      grabcad.com/library/motorcycle-lift-5

  • @dignitas1980
    @dignitas1980 7 років тому

    Great job, man! It`s the same priciple like the double scissors lift stand?

  • @tomayrscotland6890
    @tomayrscotland6890 Рік тому

    Hi fella been looking for an easy build myself I could do with some plans am a bit slow with your video i cant seem to catch it with my camera and i would not like to copy it without your consent... Tom in Ayr.

  • @walterarquinego7933
    @walterarquinego7933 7 років тому +1

    excelente trabajo , gracias por tu dedicacion

  • @daniela56dio
    @daniela56dio 6 років тому

    0:27... What do we called it? Hydaulic jet or mini pump? Looks like piston.

    • @emillyudmilov
      @emillyudmilov  6 років тому

      На български е "хидравличен крик"
      In Bulgarian is a "hydraulic jack"

  • @joeheydenrych1240
    @joeheydenrych1240 5 років тому

    Good Day Sir,
    Are you selling these plans? From SA
    Regards

    • @emillyudmilov
      @emillyudmilov  5 років тому

      give me an email to send them to you

    • @emillyudmilov
      @emillyudmilov  4 роки тому

      The 3D model can be downloaded from GrabCad
      grabcad.com/library/motorcycle-lift-5

  • @mirocingel5975
    @mirocingel5975 7 років тому

    Hello Emil, it´s great project. Please, could you send me more info about this lift or solid works file?
    I would like to use in my job. Thanks for answer.

  • @ichaicha5868
    @ichaicha5868 2 роки тому

    Can you please send me a copy of the build?

  • @gtacars3769
    @gtacars3769 9 місяців тому

    Hello Emil, can you send me the solidworks file from this draw?

  • @johanjoubert9881
    @johanjoubert9881 4 роки тому

    Hi sir good job. WouI'd you please share the cutting list with me? Thanks

    • @emillyudmilov
      @emillyudmilov  4 роки тому

      The 3D model can be downloaded from GrabCad
      grabcad.com/library/motorcycle-lift-5

  • @aastik5
    @aastik5 5 років тому

    Which software used in this project

  • @JulianBiedziak
    @JulianBiedziak 2 роки тому +1

    hello, is it possible to send 3D files and material application?

  • @robxclusiv3
    @robxclusiv3 8 років тому

    Hello Emil, ive wanted to ask you if you have measurements for this build. I would love to build this for myself :D

    • @emillyudmilov
      @emillyudmilov  8 років тому

      If you give me an email, I can send you the information by "motorcycle lift" which I stayed, unfortunately it is not much.

  • @davidolivier2775
    @davidolivier2775 5 років тому

    Hello Emil, it's a very awesome build , just what I was looking for.
    Can you please send me a copy of the build.
    I'm working on project bikes and has been looking for ideas on workbenches for some time now, tired of working on the floor :-)
    This is the best I've come across in all my searches, great design.
    I would like to use your idea if possible please.
    Best regards
    David

    • @davidolivier2775
      @davidolivier2775 5 років тому

      Please mail to DavidFoli4@gmail.com .... Thank you in advance for sharing.

    • @emillyudmilov
      @emillyudmilov  5 років тому

      I've sent you an email

    • @ionmunteanu9829
      @ionmunteanu9829 Рік тому

      @@emillyudmilov вадаада

  • @oldtimer-veteran5393
    @oldtimer-veteran5393 3 роки тому

    Hey ho, tolle Umsetzung. Ich habe es mir da etwas einfacher gemacht und einen hydraulischen Hubtisch aus einem Krankenwagen / RTW als Motorradbühne umgebaut. Gruß

  • @alexsafarov3066
    @alexsafarov3066 4 роки тому +3

    Доктор дью показал как выглядит домкрат для мотоцикла

  • @tomthompson7400
    @tomthompson7400 7 років тому

    hi , would it be possible to get a set of plans please
    tom.thompson

  • @phuketbungalowinfo2757
    @phuketbungalowinfo2757 8 років тому +1

    coooool, THANKS for sharing Emil, looks like much work

    • @emillyudmilov
      @emillyudmilov  8 років тому

      Well, it took me four days work, it was designed for applying for a job.Thank you for your attention

  • @popppcattt2
    @popppcattt2 Рік тому

    Hi Emil, I would like to fabricate this. Could you please send me the DWG or DXF drawing ?

  • @Podpolchik
    @Podpolchik 4 роки тому +1

    Хорошая конструкция, для подъёма опускания сварочного стола.

  • @aliomari6246
    @aliomari6246 8 років тому

    can i get the solidworks file if you have please , i want to convert it to my project ? :)

    • @emillyudmilov
      @emillyudmilov  8 років тому

      Unfortunately not keep SolidWorks files, but I have a file in "Parasolid Binary(*.x_b)", which you can open with SolidWorks and look at all the elements separately from the Assembly.
      If you want to send this file, send me email adress.
      Regards

    • @aliomari6246
      @aliomari6246 8 років тому

      mr.ali.pash@gmail.com
      thank you.

    • @emillyudmilov
      @emillyudmilov  8 років тому

      send e-mail

  • @juanantonioespanolbrau9537
    @juanantonioespanolbrau9537 8 років тому

    hola creo que faltan las medidas y los tipos de perfiles es decir un poco más especificado así como distancias diámetro de ruedas ect.

    • @emillyudmilov
      @emillyudmilov  8 років тому

      Сметките са по FEM и се получават такива профили и колела, заданието беше за повдигане на 400 кг.

  • @charlesjose9037
    @charlesjose9037 5 років тому

    Qual tamanho do eixo do cilindro

    • @charlesjose9037
      @charlesjose9037 5 років тому

      Medidas desse projeto

    • @emillyudmilov
      @emillyudmilov  4 роки тому

      The 3D model can be downloaded from GrabCad
      grabcad.com/library/motorcycle-lift-5

  • @funkyoldmedina4232
    @funkyoldmedina4232 7 років тому

    Sweet project !!! I just came across your video, I'm wanting to build one. Do you have the plans and specs. and materials it will take? Just liked and subscribed.

  •  8 років тому

    Nice, it looks great! Can you send me solid works file

    •  8 років тому

      david.luzar@gmail.com
      Thank you!!

  • @janbacher3765
    @janbacher3765 2 роки тому

    If looks very nice. Can you please send me the file.
    You would save me much time. The file format STEP would be the best

  • @gustavoarielsilva1402
    @gustavoarielsilva1402 3 роки тому

    Hola. Cual serían las medidas

  • @titou-nv8gr
    @titou-nv8gr 4 роки тому

    hi I would like to know what is your software that you make your drawings and what little gives the no of the software I thank you

  • @emillyudmilov
    @emillyudmilov  4 роки тому

    The 3D model can be downloaded from GrabCad
    grabcad.com/library/motorcycle-lift-5

  • @IvanNotEasyToFindFreeName
    @IvanNotEasyToFindFreeName 2 роки тому

    Емо здравей! Клипа е доста стар, но все пак се надявам, че коментара може да достигне до теб. Търся си стойка за мотора и попаднах на твоя клип. Исках да те попитам дали изработвате такива стойки или само ги проектирате?
    Поздрави,
    Иван

  • @marcelfillipmattos6285
    @marcelfillipmattos6285 4 роки тому

    Muito bom ,poderia passar as medidas e os materiais

    • @emillyudmilov
      @emillyudmilov  4 роки тому

      The 3D model can be downloaded from GrabCad
      grabcad.com/library/motorcycle-lift-5

  • @giorgiobassi9078
    @giorgiobassi9078 2 роки тому

    Awesome. ✌️👍🇮🇹

  • @dnkandelmundo8328
    @dnkandelmundo8328 4 роки тому

    @Emil Lyudmilov TQVM

  • @juanjaguiarm2510
    @juanjaguiarm2510 6 років тому

    Y AHORA COMO METO LA MANO PARA EL GATO HIDRAULICO,,,, TE FALTO UN MECANISMO,,,

    • @emillyudmilov
      @emillyudmilov  5 років тому

      I did not understand. send an email to send them to you if you want me to send

  • @mazenalfar5953
    @mazenalfar5953 4 роки тому

    رائع يا فنان

  • @kadirseyirci2635
    @kadirseyirci2635 4 місяці тому

    Ölçüler alabilirmiyim 🎉

  • @jee6473
    @jee6473 Рік тому

    Can you give me sldprt? 😂

  • @JKT_bonsai
    @JKT_bonsai 8 місяців тому

    ❤❤❤tanks❤❤

  • @pauloprato
    @pauloprato 5 років тому

    Great.... Could you please send me project/ dimensions? I am from Brazil. Thank´s a lot.

    • @emillyudmilov
      @emillyudmilov  5 років тому

      give me an email to send them to you

  • @pelaez8808
    @pelaez8808 3 роки тому

    Cómo se manipula ... Falta adaptarle sistema de elevación

  • @MarcSpeedvisio
    @MarcSpeedvisio 11 місяців тому

    Exellent work

  • @leoneifert4503
    @leoneifert4503 2 роки тому

    gracias master

  • @mohd.hussain1478
    @mohd.hussain1478 4 роки тому

    Sir can you provide me with the drawing

  • @PatrickCiresi
    @PatrickCiresi 5 років тому

    Any chance you can send me the file?

    • @emillyudmilov
      @emillyudmilov  4 роки тому

      The 3D model can be downloaded from GrabCad
      grabcad.com/library/motorcycle-lift-5

  • @ПошолНахуй-ц8н
    @ПошолНахуй-ц8н 4 роки тому

    Молодец.

  • @recepdurmus7702
    @recepdurmus7702 4 роки тому

    Muhteşem 🙏

  • @gj4057
    @gj4057 5 років тому

    做得不错

  • @SalmanKhan-vh8hk
    @SalmanKhan-vh8hk 3 місяці тому

    Iska parts de do Saman banaa lena

  • @Charlie1993ohio
    @Charlie1993ohio Рік тому

    can i get some blueprints for this?????

  • @juanantonioespanolbrau9537
    @juanantonioespanolbrau9537 8 років тому

    de todas formas lo encuentro muy bien

  • @Vasjanuch
    @Vasjanuch 4 роки тому

    Кто здесь?

  • @socratemartinez9043
    @socratemartinez9043 7 місяців тому

    exelente

  • @tbddiy3258
    @tbddiy3258 3 роки тому

    👍

  • @mohmmadfariyadfariyad2692
    @mohmmadfariyadfariyad2692 3 роки тому

    Hi

  • @khairulsaleh1
    @khairulsaleh1 5 років тому

    😘

  • @calanto55
    @calanto55 3 роки тому

    Ottimo progetto puoi inviarmelo via email a calanto55@hotmail.it

  • @نعمنعم-ث2ث
    @نعمنعم-ث2ث 4 роки тому

    س

  • @pp6pe1
    @pp6pe1 5 років тому

    favor enviar projeto com as dimensões para pp6pe1@gmail.com. agradecido

    • @emillyudmilov
      @emillyudmilov  4 роки тому

      The 3D model can be downloaded from GrabCad
      grabcad.com/library/motorcycle-lift-5