Never in my life would I have thought a video of someone disassembling and reassembling a Trabant gearbox would be entertaining. Well you proved me wrong, good job!
IRC the white cat version was 15bhp less, the ginger cat equivalent was much more economical and reliable, no ones ever dared making the black cat version, I'm hoping AMG will consider it :D
As a German I can only congratulate you on your efforts with these cars. Sadly now they have gotten quite expensive (at least for being basically a shoebox on wheels) but 15 years ago you could still get these vehicles in perfect condition for a couple of hundred euros and non running ones basically for a case of beer and "get it off my lawn by saturday evening"
Some tips/education: - The cover with the spiral metal thingy you first took off the gearbox is basically an oil pump. It goes inside the shaft and as the shaft turns, the spiral metal thingy helps the oil flow to the gears. - The red cover should be made of metal and a concave shape. It's fixed in place by putting it in its hole with the concave side inside, then hitting it with a hammer, so its concave shape "flips" to the other side, making the cover to stuck in the hole. Some sealant/glue is also needed.
A few months ago I did the same thing to my Trabant´s transmission, because the freewheel clutch had died. As far as I understand it however, it is the surface of the inner race that is wearing down and the rollers can´t wedge themselves onto it anymore. As I wasn´t sure whether my transmission was the old or the new version, I had ordered both versions of the freewheel inner race. After measuring the ID of both parts, I can assure you that both of them are exactly the same ID(down to 0.01mm/ roughly .0005"), so both versions will press on the same shaft with a hydraulic press, as you demonstrated. Heating/torching is not required on either install or removal. Why the key was omitted later is beyond my knowledge, one might suspect cost savings thou. But I´m still surprised that your key was sheared off. Make sure that the speedometer drive has some up/down movement, as this can happen when the unit slips during assembly. If the shaft is not moving, you can add a shim washer underneath the bushing. And the weird oil feed screw is, as you suspected, forcing oil into the hollow shaft and out through ports to lubricate the gears. When I disassembled my transmission, I was equally puzzled by the manual, which is sometimes difficult to understand even as a native German. Anyway, the cover containing the oil feed thingy had been RTV´d generously by the previous owner of my Trabant, so I tried to carefully pry off the cover, slipped, and bent the hell out of the oil feed device. Bent it roughly back straight, transmission is fine. Reminds me of doing an oil change, though... Been daily-driving my 1969 Trabant for almost six years now, btw.
Well, your right! RIP the earth though. You know, I'm 16 and live in Belgium (so trabis are not that far away). And I hope I can own one one day! Enjoy yours!@@marbella91
@@vini1277 There's a catalytic converter available for Trabis. I've been driving with one for about 5000 kilometers and it has no negative effect on power output of the engine.
Wow I didn't know that! Does that mean it could pass emission tests for regular cars? Because if I'm not mistaken it has to pass that to be able to be a daily driver?@@purplesparc
Lassi Kinnunen In german you could also compound forever... (Rindfleischetikettierungsaufgabenübertragungsgesetz (i think) was the longest german word once)
It's oddball to you, friend. I'm from Bulgaria (eastern Europe, Balkans). Here, as we were under communist regime from 1944 to 1989 - the Trabi is quite common. It was old even when i was 12 years old. And it was the first car, that got me interested in mechanical stuff. Then there was the Lada 2101, and other classic russian clankers... All of those primitive commie machines have a place deep in my heart. Ridiculously simple, and almost idiot-proof! There are a lot of them running around here, even in 2019. Yet i still drool, when i think how americans built their cars back then. Still simple, rugged and reliable as hell, but much more powerful and comfortable, and there is no need to even mention how much more beautiful and cool they were (and are, to this day)!
As a veteran of classic VW Beetle engine rebuilding, this is about as entertaining as a German transmission rebuild video can get. Keep up the stellar work sir!
How could 6 people give this video a thumbs down? Is there Trabant gearbox rebuild videos on UA-cam that are superior to this one? Or equal to this video? Or another video to compete with this one at all? Well if there is one I refuse to believe it's better than this glorious video. UA-cam was invented for quirky, homemade videos just like this.
Holy crap this is entertaining! I can't say I have ever split a gearbox while half standing on a workbench and half standing on a stepladder and ending up with the countershaft and gearbox stuck and wondering how I would get down. This is awesome, 10/10
Interesting stuff! Those graphite release bearings were also used in some British cars, although my late MG Midget has the roller type as used by Triumph in the Spitfire. A definite rule of thumb with those bearings is to avoid disengaging the clutch except for gear changing. For example, no holding the clutch down at stoplights, etc. Enjoyed this one, thanks!
You may not think your a mechanic, but you are. And by working on this you are showing us how to do it. Even if you don't do some things right, you are showing us what to expect and can learn from the few mistakes your making. I just need one of these cars now!
I got to give it to you for having the balls to do this. Disassembling a gear box and "not being a mechanic" is not something for the faint-hearted to tackle.
in 2004 I felt blessed to witness an actual living, breathing Trabant in real life on a trip to Cuba. Never in my wildest dreams did I ever expect to experience the thrill of witnessing the insides of a Trabant's transmission. Mein gott youtube is truly amazing! ;-)
Robert, your approach to gearbox (did)assembly and life in general is so refreshing. I have become an avid follower of both of your channels. Thank you for the content.
Fun fact: Do you know that back in 1997 when Mercedes-Benz introduced "the baby Benz" - Mercedes A classe, a huge problem emerged.The W168 became infamous in 1997 after flipping over during the traditional "elk test" performed by the Swedish automobile publication Teknikens Värld. According to the report, the W168 overturned when manoeuvring to avoid the "elk". The experts said that Trabant was actually much more stable car in rapid turns!
you sir are brilliant ! you need your own TV show ! I love the way that you freely admit you don't know what you are doing and don't try to bullshit anyone that watches this and try to prove you know everything about everything !
Order oil from Europe for Trabant gearbox. lol!!! just put any greasy liquid in it. Should be fine. Also about that lock pin for 4th gear. It's not part which you should order from 10 000 km away place. Just make one from reasonable quality material. Takes 5 minutes
@0.11 My Trabant exhaust is equipped with one of those... (a ceramic one, not an organic one) It's a 1.1 from 1991. Sometimes they got one (almost always on a later date)
Ohh man, lookin at you Trabant videos, it's joyful, i remember when my dad always fixing our Trabant, it wasn't like yours, it was bearing all over around...swearing i mean... Believe it or not, when someone decided to have one these they had order it and wait about 6 months before they got it, at least in Hungary
The one-way (Free-wheeling) clutch is also known as a sprag, and there is one in almost every electric starter motor. It keeps the starter from being spun up after the engine starts
The first part you took off (the one called "screw conveyor" in the manual) is used to circulate the oil inside the (partially hollow) intermediate shaft. The intermediate shaft has multiple holes in it that help with lubricating the moving parts on it.
Rebuilding a Trabant, so you don't have to. Seriously though, this is inspiring me to take a wrench to my 1969 2000CS which needs a lot of love. Goals for 2020...
Well, at the start I was determined to object to this, but he is really right up there with, if not ahead of the legendary Mr Hubnut's self-deprecating comentary documenting his battles with some of the world's most sub-standard and decayed automotive icons. More skill here than he admits to ! Thanks!
Ive got a Trabant myself and its my fist car bevor that i had no idea how even a sparkplug works but .. this car is like a schoolbook u can learn so much by just tearing it apart big respekt tho for the transmission
I feel a bit ashamed when my Trabbi started for the uncounted time again to play up I drove it - as it still drove to the tip and pushed it down into the ditch. So good on you to put so much work into this former East German design to keep it going. I was never happy with what I did to the inviroment. Looking into my rear vision mirror and seeing the blue two stroke smoke lingering mid air as far as I could see back I desided: no more - it has to go.
I haven’t seen any of your vids on my feed in 4 months. Tbh, I totally forgot about this channel in that time. Too bad. This channel is fantastic. Didnt even realize how much I missed it til it came up on my feed again today.
Those bearings that allows the gear assembly to turn one way but won't allowe it to spin the other way, that assembly is normally called a "one way sprag clutch"
I think that the SAAB 96 had a freewheel function on every gear. Even in reverse. You could also dissconnect/connect the thing with a small leaver down under the dashboard. Was some 28 years since I fiddled with one, so my memory might be slightly off.
Many thanks for a highly entertaining video. And yes, the graphite release bushing does seem (in ways I can't yet explain) far cooler than its mere ball bearing equipped equivalent. Well done! Keep it comin'.
Aahh yeeeees... These parts of YT.. 2am in the morning. I need to be up at 8:30am for work but I am watching how to rebuild Trabant gearbox. Sounds good.
LOL The Mr Bean of car repair! Great entertainment... and also informative, kinda... as I don't own a Trabant, nor do I ever intend on owning one. But none the less, here I sit enjoying this tear-down. Edit: The wife is also sitting here laughing at your antics, and your unrehearsed, unedited successes and misfortunes.
There are a couple of simple rules that applies to all DIY projects. #1, "If things don't go flying across the room, then you aren't doing it right!" and rule #2, if you don't make a huge mess, then you aren't trying hard enough!"
In today's episode we discover what really grinds Robert's gears.
In today's episode Robert switches gears and gets wood off his mind.
Steve G your comment says it was put up 3 days ago XD
@@emolgatheelectricsquirrel6734 patreon
Steve G oh, well thanks for supporting him
@@steveg5122 In today's episode, Robert gets exterminated by one of his commenters
Never in my life would I have thought a video of someone disassembling and reassembling a Trabant gearbox would be entertaining. Well you proved me wrong, good job!
Me neither , hey Joe get another bottle of fireball found part 2....Happy new year Ben /Alberta
"Every good marriage needs a good beating" Best line ever
Keep up the great work, Rob!
And in modern UA-cam way it had to be followed with "That was a joke"
You think his wife has stopped beating him?
And screwing followed after that.
In a video containing "grinding" and "screwing"???
Eksamen 007 im reporting your comment.
"Draw out the Speedometer drive from the bush" Hahaha! That got me dying hahaa!
I had to watch that like 10 times.. for some reason, it had me rolling on the floor.... I'm laughing now thinking about it......
I believe the engine might be more powerful if replaced with a white cat. Possibly more reliable.
Pussibly?
Do that and starting the engine will simply be a matter of petting the Trabant's doors.
Dude, I think a hamster in a wheel would provide more power and torque than the engine of a Trabant. :)
Would also sound more powerful if the cat is purring.
IRC the white cat version was 15bhp less, the ginger cat equivalent was much more economical and reliable, no ones ever dared making the black cat version, I'm hoping AMG will consider it :D
East-german born guy learning about Trabant gear box by an American ... modern times ;-)
Ich auch 😂
no shit...same here :D
AchgottAchgott! ^^'
|/\|/\|3|3/\|_/\(|
and a hungarian guy sells trabant to an American. Imagine that line in the years of 60'-70'.
As a German I can only congratulate you on your efforts with these cars.
Sadly now they have gotten quite expensive (at least for being basically a shoebox on wheels) but 15 years ago you could still get these vehicles in perfect condition for a couple of hundred euros and non running ones basically for a case of beer and "get it off my lawn by saturday evening"
I approve of adding cats to videos.
Random Cattage. LOL.
I second this
With laser pointer of course XD
9:14 The most satisfying noise ever
Except of course the Trabi's engine revving.
thebetatester800 That’s the main purpose of that cover: to make an oddly satisfying noise when it pops out
"I'm not a mechanic!"
* mechanics *
Some tips/education:
- The cover with the spiral metal thingy you first took off the gearbox is basically an oil pump. It goes inside the shaft and as the shaft turns, the spiral metal thingy helps the oil flow to the gears.
- The red cover should be made of metal and a concave shape. It's fixed in place by putting it in its hole with the concave side inside, then hitting it with a hammer, so its concave shape "flips" to the other side, making the cover to stuck in the hole. Some sealant/glue is also needed.
The metal spiral thing straight up looks like a metal burr that gets created from cutting aluminum at my work.
A few months ago I did the same thing to my Trabant´s transmission, because the freewheel clutch had died. As far as I understand it however, it is the surface of the inner race that is wearing down and the rollers can´t wedge themselves onto it anymore. As I wasn´t sure whether my transmission was the old or the new version, I had ordered both versions of the freewheel inner race. After measuring the ID of both parts, I can assure you that both of them are exactly the same ID(down to 0.01mm/ roughly .0005"), so both versions will press on the same shaft with a hydraulic press, as you demonstrated. Heating/torching is not required on either install or removal. Why the key was omitted later is beyond my knowledge, one might suspect cost savings thou. But I´m still surprised that your key was sheared off.
Make sure that the speedometer drive has some up/down movement, as this can happen when the unit slips during assembly. If the shaft is not moving, you can add a shim washer underneath the bushing.
And the weird oil feed screw is, as you suspected, forcing oil into the hollow shaft and out through ports to lubricate the gears. When I disassembled my transmission, I was equally puzzled by the manual, which is sometimes difficult to understand even as a native German. Anyway, the cover containing the oil feed thingy had been RTV´d generously by the previous owner of my Trabant, so I tried to carefully pry off the cover, slipped, and bent the hell out of the oil feed device. Bent it roughly back straight, transmission is fine. Reminds me of doing an oil change, though...
Been daily-driving my 1969 Trabant for almost six years now, btw.
Wow you daily drive your trabi? What an absolute madlad.
@@vini1277 why not? These cars were made for daily driving.
Well, your right! RIP the earth though. You know, I'm 16 and live in Belgium (so trabis are not that far away). And I hope I can own one one day! Enjoy yours!@@marbella91
@@vini1277 There's a catalytic converter available for Trabis. I've been driving with one for about 5000 kilometers and it has no negative effect on power output of the engine.
Wow I didn't know that! Does that mean it could pass emission tests for regular cars? Because if I'm not mistaken it has to pass that to be able to be a daily driver?@@purplesparc
3:35 I love the way German compound words get literally translated to English haha. Great video overall! Can't wait for part 3.
Lassi Kinnunen
In german you could also compound forever...
(Rindfleischetikettierungsaufgabenübertragungsgesetz (i think) was the longest german word once)
It's so refreshing to watch a fellow plank/total rube struggle with projects like I do. Thanks Aging Wheels!
Pfffft! This guy is a piker. I struggle way more than he does....... wait, that didn't come out right?!
Using a pencil as a clutch sounds like it would break often. That would be pointless.
That's a sharp observation.
Now i wonder if the clutch disc material is made of eraser... Lol. 😅
H a h
Yes, since lead of a pencil is made of a brittle combination of clay and graphite particles, not solid graphite
@@JohnSmith-eo5sp Depends on the pencil. A 9B is just graphite, no clay.
Just came here in the comments session to say that I love this channel. That's it. Keep entertaining us!
My neighbour has Trabant to this day and I first time in my life watch Trabant's drivetrain internals on video filmed 5000 miles away.
4:50 this moment is amazing.
This is gonna be so good when the car finally runs. I can't wait!
Well this just made a crappy Tuesday morning in a hell of a lot better.
The Trabant is the only car in which removing the engine is considered a performance upgrade
😂
"The Trabant's clutch is disengaged with a pencil" - man, I almost choked on my morning coffee!
And it can also be used for a BMW R35. At least the pads fit exactly.
The way he said it made me LOL
Everything on that car is so cute and adorable!
No it is not. It is a pile of junk and should be treated as such, IMO.
@@ghydda Don't say that, you will hurt Trabbi's feelings!
ghydda how dare you, poor Trabbi, always bullied
@@ghydda i love Trabants your a piece of junk go drive your boring ass 4cyl automatic camry filled with starbucks and cigarette butts
@@ghydda so are you saying he should LS swap it
Aging wheels releases a new Trabant video! "And there was much rejoicing."
Yayyyyyyy
Now, imagine how many other things we all have done wrong just cause there wasn't another random thing that made us look closer into it :D
Mystical antiwear oil. That sounds like a treat. What else did they have? Horse liniments and snake oil?
Its called ZINC and MOLY. Your engine loves it, Converters hate it.
@@zuestoots5176 Ravers with colds?
I'm so fascinated by these oddball cars. Thank you, Robert!
It's oddball to you, friend. I'm from Bulgaria (eastern Europe, Balkans). Here, as we were under communist regime from 1944 to 1989 - the Trabi is quite common. It was old even when i was 12 years old. And it was the first car, that got me interested in mechanical stuff. Then there was the Lada 2101, and other classic russian clankers... All of those primitive commie machines have a place deep in my heart. Ridiculously simple, and almost idiot-proof! There are a lot of them running around here, even in 2019.
Yet i still drool, when i think how americans built their cars back then. Still simple, rugged and reliable as hell, but much more powerful and comfortable, and there is no need to even mention how much more beautiful and cool they were (and are, to this day)!
Parker, you should have a look at the Citroen 2cv, 625cc engine, up from 400 odd cc, so simple to work on as well, all just unbolts.
As a veteran of classic VW Beetle engine rebuilding, this is about as entertaining as a German transmission rebuild video can get. Keep up the stellar work sir!
How could 6 people give this video a thumbs down? Is there Trabant gearbox rebuild videos on UA-cam that are superior to this one? Or equal to this video? Or another video to compete with this one at all? Well if there is one I refuse to believe it's better than this glorious video. UA-cam was invented for quirky, homemade videos just like this.
Your Trabant graphite throwout bearing is just like the old VW Beetle throwout bearings.
I'm guessing many cars used these since my MG Midget did also.
Mk I AH Sprites (948 cc) also, like the one I raced back when. (They're first cousins.)
I thought he said the Trabant had a "throw-out bushing"
@@JohnSmith-eo5sp A bushing is another name for a plain bearing, i.e. a bearing with no rolling elements.
@@yt45204 probably
You've successfully turned the Trabant gearbox into a bobblehead
I think this is my favorite car channel at the moment. Great writing, great content, great humor. 👍👍
20:19 "And like any good marriage, a beating is required." 🤣
I appreciate the simplicity of things like this and vintage VWs.
I just figured out that the cat at the beginning is supposed to be a catylic converter
Holy crap this is entertaining! I can't say I have ever split a gearbox while half standing on a workbench and half standing on a stepladder and ending up with the countershaft and gearbox stuck and wondering how I would get down. This is awesome, 10/10
Interesting stuff! Those graphite release bearings were also used in some British cars, although my late MG Midget has the roller type as used by Triumph in the Spitfire. A definite rule of thumb with those bearings is to avoid disengaging the clutch except for gear changing. For example, no holding the clutch down at stoplights, etc. Enjoyed this one, thanks!
You may not think your a mechanic, but you are. And by working on this you are showing us how to do it. Even if you don't do some things right, you are showing us what to expect and can learn from the few mistakes your making.
I just need one of these cars now!
I got to give it to you for having the balls to do this. Disassembling a gear box and "not being a mechanic" is not something for the faint-hearted to tackle.
You are the very antithesis of Bad Obsession Motorsports.... I salute you and BOM!!!
in 2004 I felt blessed to witness an actual living, breathing Trabant in real life on a trip to Cuba. Never in my wildest dreams did I ever expect to experience the thrill of witnessing the insides of a Trabant's transmission. Mein gott youtube is truly amazing! ;-)
Robert, your approach to gearbox (did)assembly and life in general is so refreshing. I have become an avid follower of both of your channels. Thank you for the content.
Fun fact: Do you know that back in 1997 when Mercedes-Benz introduced "the baby Benz" - Mercedes A classe, a huge problem emerged.The W168 became infamous in 1997 after flipping over during the traditional "elk test" performed by the Swedish automobile publication Teknikens Värld. According to the report, the W168 overturned when manoeuvring to avoid the "elk".
The experts said that Trabant was actually much more stable car in rapid turns!
You need your own tv show. Love this guy!
Why on earth this is SO entertaining is beyond me. but i cant stop watching this videos.
you sir are brilliant ! you need your own TV show ! I love the way that you freely admit you don't know what you are doing and don't try to bullshit anyone that watches this and try to prove you know everything about everything !
Order oil from Europe for Trabant gearbox. lol!!! just put any greasy liquid in it. Should be fine.
Also about that lock pin for 4th gear. It's not part which you should order from 10 000 km away place. Just make one from reasonable quality material. Takes 5 minutes
There a many of these still running around Bulgaria today!
Тъкмо това обяснявах на Marc по-горе!
@0.11 My Trabant exhaust is equipped with one of those... (a ceramic one, not an organic one) It's a 1.1 from 1991. Sometimes they got one (almost always on a later date)
9:41 smell of my childhood, always takes me back
Ohh man, lookin at you Trabant videos, it's joyful, i remember when my dad always fixing our Trabant, it wasn't like yours, it was bearing all over around...swearing i mean...
Believe it or not, when someone decided to have one these they had order it and wait about 6 months before they got it, at least in Hungary
Refreshing to enjoy your humility, humor and intelegence. Thanks
The one-way (Free-wheeling) clutch is also known as a sprag, and there is one in almost every electric starter motor. It keeps the starter from being spun up after the engine starts
The first part you took off (the one called "screw conveyor" in the manual) is used to circulate the oil inside the (partially hollow) intermediate shaft. The intermediate shaft has multiple holes in it that help with lubricating the moving parts on it.
@ 15:34 who else thought when he said focus he was talking to us 😂😂
Rebuilding a Trabant, so you don't have to. Seriously though, this is inspiring me to take a wrench to my 1969 2000CS which needs a lot of love. Goals for 2020...
Well, at the start I was determined to object to this, but he is really right up there with, if not ahead of the legendary Mr Hubnut's self-deprecating comentary documenting his battles with some of the world's most sub-standard and decayed automotive icons. More skill here than he admits to ! Thanks!
I laughed so hard when you got stuck on top of your step stool with the differential.
thats for waking up my addiction to trabants again;. I had to rewatch Trabant Trek just to get my fix till you upload next trabant video
this is incredibly entertaining. even as a guy who usually isn't intrested in cars or engines.
At points this is almost like watching a Druaga1 video except its not old PCs it's old cars. I love it
Surprisingly satisfying to watch
I love this series, and your channel in general. Keep up the good work!
Ive got a Trabant myself and its my fist car bevor that i had no idea how even a sparkplug works but .. this car is like a schoolbook u can learn so much by just tearing it apart big respekt tho for the transmission
You got a thumbs up because of that AMAZING animation for the one-way-bearing.
I'm loving this project, great work!
Love your work. Nice refreshing style.
Great video as always, keep it up!
Can't wait to see the Trabant in action again
Loved the video and your editing magic in the beginning! Keep up the good work.
I am LOVING these! Keep'em comin'!..... with a beating.....
I feel a bit ashamed when my Trabbi started for the uncounted time again to play up I drove it - as it still drove to the tip and pushed it down into the ditch. So good on you to put so much work into this former East German design to keep it going. I was never happy with what I did to the inviroment. Looking into my rear vision mirror and seeing the blue two stroke smoke lingering mid air as far as I could see back I desided: no more - it has to go.
Absolutely love your editing!
I haven’t seen any of your vids on my feed in 4 months. Tbh, I totally forgot about this channel in that time. Too bad. This channel is fantastic. Didnt even realize how much I missed it til it came up on my feed again today.
Whow a ton of work...Well Done...Will be looking forward to the next segment..!!!
Brilliant thank you for some great entertainment, and also some knowledge, keep up the great entertainment.
Love the video, keep up the good work! Look forward to part 3.
I can't wait for the next episode. That little car is lovely!
I love your sense of humor. Can't wait for the next vid!
I've been waiting for this from when you posted the first part!
You crack me up! Thanks for an entertaining 24 minutes and change.
Those bearings that allows the gear assembly to turn one way but won't allowe it to spin the other way, that assembly is normally called a "one way sprag clutch"
Robert has uploaded content, I put everything aside to enjoy it.
Great work like always.
This was the best explanation of a transmission rebuild I've seen. Really interesting. Thanks. Great content.
I haven't watched the video yet, but I've been waiting for this! Keep going my friend! Love your content!
Long Wednesday made short thanks to this, honestly looking forward to part 3!
Loving the series, keep it up!
I've been waiting 4 months for this! It was the first of your vids I saw. Can't wait for the rest!
Hands down the most entertaining channel on UA-cam. So epic!
I think that the SAAB 96 had a freewheel function on every gear. Even in reverse. You could also dissconnect/connect the thing with a small leaver down under the dashboard. Was some 28 years since I fiddled with one, so my memory might be slightly off.
Anyone else think the Trabi looks shocked in the thumbnail, like the surprised pikachu meme?
It certainly looks distraught.
I really can appreciate the humor you have, it's very similar to the humor of many technicians at the dealership I worked at remarkably. Keep it up!
For someone who says he's not a mechanic, your great!
"Ooppp! Yep. They went everywhere." Hilarious video. Made my evening.
Many thanks for a highly entertaining video. And yes, the graphite release bushing does seem (in ways I can't yet explain) far cooler than its mere ball bearing equipped equivalent. Well done! Keep it comin'.
Awesome video! much love from South Africa !
Aahh yeeeees... These parts of YT.. 2am in the morning. I need to be up at 8:30am for work but I am watching how to rebuild Trabant gearbox. Sounds good.
I think this was the best episode you did. Did not yet see all but I'm working on it...
Greetings from Dresden. Very nice job, can't wait to see the engine reassemble Video.
LOL The Mr Bean of car repair! Great entertainment... and also informative, kinda... as I don't own a Trabant, nor do I ever intend on owning one. But none the less, here I sit enjoying this tear-down. Edit: The wife is also sitting here laughing at your antics, and your unrehearsed, unedited successes and misfortunes.
There are a couple of simple rules that applies to all DIY projects. #1, "If things don't go flying across the room, then you aren't doing it right!" and rule #2, if you don't make a huge mess, then you aren't trying hard enough!"