We've got a 5gal bucket pump that we're using. Takes 4 chains just to get everything up tower to pack a main bearing (two technically). This would be a lifesaver.
Pretty menial task here, the most important thing is cleanliness. It should take maybe an hour between un-packing, setting up, doing full greasing, with cleanup and flushing, then repacking. No reason to be "bullshitting" in between, either. Lots of things can be done in the meantime.
there is a story about the Tennessee Valley Authority trying to figure out why they were losing motors in nuclear power plants . Turns out the main cause was Over-greasing ! Simple Fact - bearings should be greased (Perfectly) when the machine is manufactured . Everything done after is a mistake . Where does 36 tubes of grease go ? If you watch videos of wind turbines burning up - it’s because of bearing failure
Yes, it is possible to overgrease bearings, and doing so can lead to several issues. Bearings require lubrication to reduce friction, dissipate heat, and protect against corrosion and wear. However, the correct amount of grease is crucial for optimal performance. Overgreasing can cause: Increased Friction and Heat: Excess grease in a bearing can lead to increased friction as the bearing elements must move through the excess lubricant. This can generate more heat, potentially leading to overheating, which can degrade the grease and damage the bearing. Pressure Buildup: Overgreasing can cause excessive pressure buildup inside the bearing housing. This pressure can lead to seal failure, allowing grease to escape and contaminants to enter, which compromises the bearing's integrity and lubrication. Grease Deterioration: The excessive heat from overgreasing can accelerate the deterioration or oxidation of the grease, reducing its effectiveness as a lubricant. Energy Loss: Bearings with too much grease require more energy to rotate, which can lead to higher energy consumption in machinery and equipment. Contamination: When seals fail due to overpressurization, it not only allows grease to leak out but also permits dirt, dust, and other contaminants to enter the bearing environment, further reducing the lifespan of the bearing.@@rossmoody7744
Very cool and simple. Thank you for showing this/ 36 tubes sounds like a major hassle.
We've got a 5gal bucket pump that we're using. Takes 4 chains just to get everything up tower to pack a main bearing (two technically). This would be a lifesaver.
Have you tried it in -20°c? It isn't as fast then 😅 after winching up the grease
That's wonderful experience..its easy and clean way for greasing..I have use this ..
Have to love the Castrol grease!!
Is the lube biodegradable or does it just drop down and contaminate the ground?
Great video, is the Hove pump available in Europe?
Must be. We have them in the UK
I’m way more impressed how clean that og 2.3 is. Where is this?
The nacelle looks clean, hub was a mess though.
Muito boa essa bomba!!
Looks good
Mbr Grease 🔥
Hi What company is hiring experienced technicians who can tell me thank you
Did you ever find a job?
Depends on where you live ?
And the type of work .
Guessing a master electrician can find work
Pretty menial task here, the most important thing is cleanliness. It should take maybe an hour between un-packing, setting up, doing full greasing, with cleanup and flushing, then repacking. No reason to be "bullshitting" in between, either. Lots of things can be done in the meantime.
🥱
there is a story about the Tennessee Valley Authority trying to figure out why they were losing motors in nuclear power plants .
Turns out the main cause was Over-greasing !
Simple Fact - bearings should be greased (Perfectly) when the machine is manufactured . Everything done after is a mistake .
Where does 36 tubes of grease go ?
If you watch videos of wind turbines burning up - it’s because of bearing failure
That is never the reason. You don’t know what you’re talking about.
Complete nonsense
Yes, it is possible to overgrease bearings, and doing so can lead to several issues. Bearings require lubrication to reduce friction, dissipate heat, and protect against corrosion and wear. However, the correct amount of grease is crucial for optimal performance. Overgreasing can cause:
Increased Friction and Heat: Excess grease in a bearing can lead to increased friction as the bearing elements must move through the excess lubricant. This can generate more heat, potentially leading to overheating, which can degrade the grease and damage the bearing.
Pressure Buildup: Overgreasing can cause excessive pressure buildup inside the bearing housing. This pressure can lead to seal failure, allowing grease to escape and contaminants to enter, which compromises the bearing's integrity and lubrication.
Grease Deterioration: The excessive heat from overgreasing can accelerate the deterioration or oxidation of the grease, reducing its effectiveness as a lubricant.
Energy Loss: Bearings with too much grease require more energy to rotate, which can lead to higher energy consumption in machinery and equipment.
Contamination: When seals fail due to overpressurization, it not only allows grease to leak out but also permits dirt, dust, and other contaminants to enter the bearing environment, further reducing the lifespan of the bearing.@@rossmoody7744
Well good thing that the system the guy is filling is just a hopper for an auto-lube system, so no need to worry.
WAST OF TIME AND MONEY .