I've never commented before but Wish to express my gratitude to the UA-camr. The 4S store quoted for $1400 and I followed this protocol to change the touchscreen, spending only $15. I wish you be awarded Nobel prize for this discovery.
Thanks, saved me hundreds of dollars, almost $2k if I wanted to go through VW. A few notes: You will need T6, T7, and T20 Torx screwdrivers, the T20s take the stereo out of the car, the T7 removes the casing, and the T6 is for the circuit board. He also skips a few steps, presumably because it's hard to do them while holding a phone to record. Only one thing really stumped me for a few minutes until I figured it out: When you get the part where you are removing the circuit board/screen from the outer casing, there are clips next to the SD card readers that you have to press in order to release the board. You CAN remove the SD cards as he says, but you do not need to. Still, I found it easier to just take them out as this made accessing the clips easier for both removal and replacement. I spent in total about $25 dollars on this repair, and that cost included a $10 Torx screwdriver set. Be sure not to overtighten the screws affixing the board to the screen as this will apply pressure to the screen and give you white spots on the screen while you're using it. It's annoying, because by the time you realize you tightened them too much, you've already plugged everything back in.
What a find, thought it would cost me hundreds of pounds , but just like in the video it cost less than 30 with a bit of elbow grease and a couple of hours to do the job. I can't recommend this guy enough. Thank you Thank you.
Thanks so much; I've just spent a good portion of a Bank Holiday Monday successfully repairing the screen on my partners 2016 Yeti with the help of your video. Not only does the head unit now work perfectly, the level of smug satisfaction I've got from fixing a thing properly is through the roof - she's already fed up with me prancing around the house like I'm the god of car audio repairs.
Brilliant cheap and straightforward fix. Been living with stations jumping about and the odd random calls for over 2 years now, but wasn't parting with £800 for new unit. Part came from Aliexpress in less than 2 weeks, 2 hours work this morning and working as new. Thank you....
Thanks for taking the time to post this. Really easy to follow. I have a Discovery nav (2017 California Beach ) with an ALPS chip set next to the SD Card reader. To remove the screen from the PCB I had to remove both the vertical SD card readers as there’s a small pressure clip on each that needed to be pushed to release the touchscreen. One other build - reset the head unit after reinstalling (on mine it was just pressing the power button and holding for 10+ seconds until the unit restarts. The new digitiser didn’t work until I did this.
Great job Duncan! I was offered a replacement unit by VW for $1700. That included 60% goodwill from them. In other words a new unit with instalation would cost about $4k. I decided for $1700 I'd be better off buying a 3rd party replacement unit -- until I saw your solution. Now after spending less than $20, I have a fully working unit again. Thanks for the clear instructions and the link to the touch screen vendor. WELL DONE MATE!
Duncan thank you so much for this, many little tips you gave helped massively . Just a couple of things that may improve. 1. Remove the metal shroud totally which gives you almost the extra gap you need to double layer the digitiser. 2.If you follow no.1 then clean both pieces and use the sticky to glue then together. When reassembled i did the screw up fully bit very minor torque and screen has no white spots or anything else and buttons do not rattle. the only way you'd know it had been carried out was a slightly dimmer screen. Once again many thanks , i ordered the same as you from aliexpress for my 6.5 and it came in 10 days and cost £8.50.😍
Thank you so much from Australia.. I learned from your video that the problem could be fixed cheaply and I immediately followed link to order the part from Aliexpress. Local VW dealer quoted me AUS $3919 ( $3519 for parts and $400 service fee) to replace it for my 6 years old Caddy. Touch screen stopped working a year ago. The touch screen arrived today from China after 2 weeks. I also used another video from "neuromangler" for a lot more details in the repairing process. I ended up spending AUS $20 plus 2 hours of my time. It is now working like a new one. Huge thanks!!! Duncan!
AWESOME!!!! I got it resolved thanks to your video. It was easy and within 20 minutes I had my VW Passat 2016 stereo functioning as intended. The dealership wanted $800 for a new radio. Thanks again!!!!
Success! The right half of the screen failed to respond to touch and this fix worked a treat! Struggling to get the trim fitted on again, around the AC controls though. Thanks so much for this!!!!!
Thanks for the vid. As others have said, worked perfectly and saved a fortune. The only bit that’s missing and that caught me out slightly were the little clips next to the SD card readers. They needed unclipping before the board came away from the screen. Other than that, all fairly straight forward.
Just started experiencing issues with my screen and so glad I found your vid. Replacement screen ordered and looking forward to a fully functioning screen again! Thanks for the vid!
This is exactly what I had to do for my 2017 VW Jetta. Your instructions were 100% accurate. Thanks so much. It cost me $25 for the part which was mostly shipping.
Thank you!! This worked perfectly for my 2017 Jetta. Screen only took a week to get here. Mine head unit is a little different as the release tabs are on the inside and I had to remove that small daughter board as well. I had to run to Home Depot to get a Torx key set, I needed T6 & T8. I advise anyone doing this to make sure to have all smaller Torx sizes before beginning.
Thank you so much for sharing that fantastic solution. A 15$ job instead of 350$ to replace the screen or 2400$ + labor to replace the radio at the dealer. The most difficult part is to remove the plastic frame around the radio. It helps to have good plastic tools for that.
Thank you very much Duncan, this has saved me a lot of money as I was contemplating a replacement unit altogether, I bought the screen as per your recommendation and bought some precision torx screwdrivers at a total cost of about £20 for the two items and have just finished the job and put the unit back in my CC and hey presto.....it all works again. Thanks again 💯👌👍
Thank you! I just fixed my broken Jetta radio with this video. Putting the new screen on over the old screen worked perfectly. I'm so grateful. Good job!!!
Strange how everyone’s digitiser goes on the right hand side, isn’t it? Mine too! Wouldn’t have dared to try tackling this without this video. Shame that at the critical bits the video stops and then restarts when the dismantling has been done. However, really useful to show you what you need to do and I understand that when you are trying to video what you are doing you can’t do both at once! Once you’re in there it’s quite self explanatory. A lot of little torque screws to remove but just take a photo at each stage and you’ll know which hole they need to go back in. A bit nerve wracking and of course you don’t know if it’s worked until you’ve put it all back together, but it did so well pleased. Thanks a lot Duncan. Keep up the good work!
Hey there - thank you very much for the guide. I ordered a new screen 9 days ago from your link below ($14 delivered to Sydney), it arrived today and took me 25mins to fit. Its fantastic to have control of my radio after 10 months since the touch screen failed. I've placed this one over the top without breaking into the screen unit like you (@ 5:35). The new screen comes with a glued edge and attaches to the alloy border on the old unit - I needed to remove the glue protection (paper) and place it accurately first time, no second chance. I can now use Android Auto again as was not possible to add a new android auto device without touching the screen (android auto/screen mirror selection) - that's been a major headache for a long time. I'd been quoted $3000+ for a new unit, or $800 for a stolen one with no security codes..... Duncan you're a legend sir.
Thanks for taking the time to let me know! Saving someone else fro the pain i went through trying to work out how to fix this makes taking the time to document it worth while. Thanks!
Thank you for taking the time to do this video. You’ve saved me so much time, effort and money! I did this fix on a 2017 Seat Alhambra with a touchscreen that was partially non responsive and driving me mad. Your fix worked a treat. Thank you again for this!
You were the first video I seen that suggested leaving the old screen on. Worked perfect. Thanks. Only thing to add is make sure anyone doing this orders a small precision torex screw driver set along with the replacement screen. Torex head sizes for the internal radio screws were very small T 5 I think. I chanced a small flathead and got away with it luckily.
Thank you very much, Duncan! Very good solution for an otherwise really expensive problem. It took some time for me to find out how to separate the circuit board from the display assembly. There are some plastic clips at the SD-cardreaders.
Holey moley! Duncan, I can't thank you enough! The ghost touches / not at all responsive faulty original screen were driving me crazy for about two years, skipping tracks back and forth and dialing extra numbers while talking on the phone. My local dealer said all they could do was to replace the whole unit and quoted me €1100 just for a new unit, with additional labor cost etc. Then I stumbled upon some mail-in online offers, which still were ranging from €300-€450... I was almost willing to save up that money just to get a working touch screen again. I recently got a new mobile phone - while my old phone always connected automatically via bluetooth the new phone hasn't been paired yet. Even though it's possible to use the physical buttons to navigate to the bluetooth pairing mode and select a phone, the very last step to confirm a pairing code can only be done via touch screen - and the old one just wouldn't react at all (except for two spots in the very bottom left and right corner - but far away from the confirmation box). Then, just by chance, this video popped up in my recommendations. I watched it, was very intrigued and mailed the same vendor that you linked to with photos of my unit and he pointed me towards the proper touch screen I needed. I also ordered some tools to remove the faceplate surrounding the radio unit. About 11 days later the new touch screen finally arrived - thanks to this video it was quite easy to follow the steps shown and just put the new touch screen on top - just as @pikey6258 described, I put the screen on the frame of the whole screen unit (not directly on top of the other touch screen inside the screen unit). Half an hour later I was back sitting in my car, really really excited and nervous if this will finally end the suffering of not having a fully functioning radio unit - but then it registered every touch right away and I could access all the menus I couldn't anymore before. It was such a relief! I could also finally connect my new mobile phone, so listening to podcasts while commuting while be very convenient again! So thank you again so so much! Without this video I might have spent 12-15 times more money to get this fixed! You sir are awesome! THANK YOU! ❤
Wow, thanks for the video! I'm definitely going to give this a try. My 2016 VW CC's screen started randomly beeping and clicking as if it were being used about two months ago. Completely unable to use navigation or even stay on a single radio station for long periods of time. I didn't even know this was a possible repair option until I found your video. Looks like it'll be around $10 to the US for me, much more affordable than the $1,100 my local dealer quoted me for replacing the entire unit!
Top man, worked a treat! Little tip - I put some foam tape on the backs of the rubber button covers, which removed any rattles. Also left the metal shroud off. Thanks again! Good to have a working radio back. Done in 1hr :)
Hey Duncan, I just had the same problem with my tiguan. Found your posting and followed the link for Ali express. Took 2 weeks, not bad from China! Thanks for the instructions, it really is a straightforward procedure and is now working perfectly. Volkswagon are infuriating! Will not accept the unit is substandard but is repairable and just want to sell you another unit for an unbelievable price. Seems this is happening world over on a regular basis but same old response from VW. Again, many thanks for your research.
My Tiguan is the same, VW said prob be over £2000 for them to replace. It went crazy, first started dialling my contacts randomly, then deleted all radio stations along with icons, then satnav went crazy putting me in middle of Europe! A guy in a repair shop who VW sales rep told me to contact still wanted £400 just to send it off to see what was wrong with it. I'm ordering this, if it works, this guy is a genius! 😁
One of the best youtuber of the world 👍 Je viens d'effectuer la réparation, sauf que je n'ai pas remis le cadre métallique ni le scotch, par choix perso, et ça fonctionne au top, réparation rapide et invisible. J'ai pris le tactile finition brillante, et c'est parfait à mon goût Thanks thanks thanks a lot man, i love toi 🥰😁
Thank-you so much for posting this video and the link to Ali Express.I have a 2017 Seat Alhambra fitted with the same head unit and I was quoted over £3,500 (!) to repair or replace the touch screen (probably would have replaced the entire unit). So your tutorial allowed me to fix the faulty touch screen for £12.......RESULT !!
Duncan, I have been searching for a solution for nearly a year - standard "you need to replace it" nonsense. Now it's fixed and fully functional for £11 thanks to you taking the time to explain and share! THANK YOU
Thanks very much for posting this video really useful. I found that once the screws were removed that secure the circuit board, I had to release plastic clip retaining each sd card readers in order to withdraw the circuit.
Hi Duncan, thank you fo posting this video. I have replaced the digitizer on my unit and it's now working perfectly again. Used the the exact one you had refrenced for my 2018 Amarok - MIB STD2 PQ +/NAV
This saved me a fortune! I bought my Cali aware of this issue from the seller, who took £1500 off the purchase price. VW wanted £2400 saying I needed a new head unit and I was quoted £1250 for a new alpine unit from a car radio specialist. So I followed Duncan’s video, thinking this can’t work… paid £10.98 for screen, £10 on some torx screwdrivers as you need T10 to remove unit, T8 & T6 to unscrew the unit and it works as it should again, thanks to Duncan.
Okay Briit Girl 55 yrs old. I did it myself - and IT WORKED!! had screws left over tho ! hahaha.. Thank you so much Duncan - Dealer quoted £650 to fix of money I just have not got. . Now tho'....am very happy! Thank you TONS! VW Skoda = Feck'em.
Just performed the install and it works perfectly! Just make sure to keep your screws organized. Thank you for the clear and concise instructions. I also bought the same screen off of AliExpress but selected the matte version to keep the same finish as the original screen.
This video helped me out tremendously. A few notes for people that are doing this or about to: 1. You do have to remove the SD card readers. 2. When you are putting things back together, you do not need to put the metal shield back on the front of the display, this just adds extra girth with no benefit. 3. DO NOT tighten screws all the way. Tighten them as lightly as you can. Tightening them too much will make the screen go white/light on the sides where the buttons are. That last point can be an exercise in patience. Tighten, reassemble radio, test. Disassemble, loosen, reassemble and test again until you get it good enough for your liking. The buttons can be a little rattle-y if you leave the screws a little loose, but that I think is a good price to pay. Good luck guys!
Дополню, сорри, что на русском. Имел сегодня секс с этим процессом. Выводы: - Если ставить сенсор поверх старого - будьте готовы к тому что на прямом солнечном свете экран заметно бледнеет, но в общем не критично. Видно нормально, да и прямое солнце светит редко. - экран начинает не сильно, но отражать. Тоже, чем больше солнца, тем больше бликов. Но тоже не критично. - причина - воздух между слоями. Почему нельзя сделать «полный-клей» на подобии защитных стекол, как на телефонах - не понятно. Уверен, это сняло бы обозначенные вопросы. - снимать металлическую рамку экрана - нет никакого смысла, так как экран упирается в лицевую панель именно сенсором, а не рамкой. Высоту «пирога» это не уменьшает совершенно, но рамка, если она есть - хорошо центрует экран в лицевой панели. - новый сенсор добавляет этой сборке лишних 1,5-2 мм и это действительно проблема. Можно конечно недожать болты, но если плата не станет на свое место, а она не станет, это выльется в следующие проблемы. Кнопки будут болтаться, карт-ридеры уйдут вглубь облицовки, плата будет перетянутая и перекошенная и может даже сломаться, особенно в зоне «крутилок», и вы не поставите не перетянув плату на место верхний металлический щиток этого экранного модуля. А следовательно - не соберете нормально устройство. - решение есть! Нормально встать плате на место мешает не экран! Плате мешают крепления рамы экрана, которые из-за дополнительной толщины сенсора поднимаются на 2 мм. Сам экран плате не мешает. Он ниже. Нужно эти крепления немного модифицировать, так, чтобы они стали на старое место. Нужно разогнуть эти крепления вверх, расточить отверстия к низу, и согнуть обратно, чуть ниже чем было. Лишнее отрезать. Рама алюминиевая и все это делается аккуратно, но не сложно. В итоге - всё становится на место как положено, «бутерброд» собирается, винты затягиваются, всё на месте, всё готово. В общем, схема рабочая, но надо иметь в виду первые два пункта. Если вас это не смущает - все это делается за час. Китайцам - отдельное пожелание, сделать всё тоже самое на липучке «полный клей». Цены не будет этому изобретению. Удачи! 👍🇺🇦
THanks for the tip, found that if the screws aren't tight enough then the buttons are mushy . Unfortunately reassembled the radio to find (as you say) I've got white spots on the screen. So reassembling it all again now.
@@carlosrafael7904 unfortunately, exactly to David's point, you'll get used to taking the front off the radio and plugging it in several times before you get it right. My 'Radio' button is still mushy and I think two of the plastic standoffs are probably not doing much holding anymore. But my screen works at least.
Like others, I found this video to be incredibly helpful! Thank you so much for posting it. And shame on Volkswagen for making it necessary. You made it much easier with this video
Thanks Duncan - a definite wallet saver. Just changed the screen on my 2017 Alhambra. Took a couple of hours and now works perfectly. Your video helped greatly.
Hallo Duncan, herzlichen Dank aus Deutschland für Dein sehr hilfreiches Video und den Link zum Ersatzteil. Die Reparatur ist mit Deinem Video einfach. 😊
Das funktioniert. Danke. Der Platz ist knapp aber wenn man die kleinen Torx Schrauben vorsichtig anzieht gehts. Am Ende von aussen nicht sichtbar. This works. Thank you. The space is bit tight but if you are careful when you fix it back (dont overscrew the small torx screws) then it goes. From outside your see nothing.
Nice video, thankyou. Quite an easy repair, having seen the video, to give me confidence. My ocd would have liked me to remove old screen.... I did attempt it, 5 mins in oven on 80 degrees, but chickened out, too tight/afraid of having to buy new lcd. This repair cost me about £15 👍👍
Yea, before i realised we don't need to remove the old touch sensor i was going to take the screen into a mobile phone repair shop; They will have the tools and experience for working with glued on sensors.
Thank-you so much for this! After years of putting up with the screen ghosting and not willing to pay £690 for someone to fix it, I found your video through the forum. 30 minutes later and it's all sorted! Thanks again
I never make comments on UA-cam videos. But this one is awesome. Shame on VW for asking for a lot of money for something that I managed to repair for 15€. Many thanks for the tutorial
Daniel in Nashville. 2017 VW Beetle vert. Took about 2.5 hours. Ordered the same screen off of ali Baba. Toughest part was getting the whole unit back in as there is little slack in the wiring harness. Note: Cleaned the original screen very well as there was a combination of grime and finger oil all around the edge once the metal frame was off. Wondered if this was cause of issue (right side of screen did not work, left- hit or miss) and if I could just clean it good and NOT put new screen over. Did put new screen over. All who do this need to also have a very clean environment. Clean the screens with sterile water and a microfiber, let dry, and try not to get anything between the two glass screens. I wore disposable plastic gloves and used a antistatic mat to keep things from sticking to the glass. Still, I found a tiny dust fiber in one corner after install and looking at it under a magnifier. Unit works though and wife is happy. This video NEEDS to be relabeled as "VW Discovery Media MIB2 faulty touch screen repair" and you will get a lot of hits. Thank you. Thank you Thank you! Also, separate issue, when I put the V 10 SD card in for navigation update, the screen says" This card has the navigation database. " Then: loading Navigation Database. Then there is a blue circle that spins round and does not stop. Have left for hours. Still just a spinning circle. Any clue as to how long it takes to update the navigation database? I saw a video of someone loading ad there is a progress bar displayed . I don't get that, just the stupid blue spinning circle. Anyone?
Красава…я не додумался даже что тупо положить новый сенсорный экран на старый сработает. Сомневался до конца. Тема реально работает, по сути всё просто. Только что сам заменил и радуюсь. Респект автору!
@@daruksdioma7205 да…я думал тоже что ерунда. А оказалось что без проблем. Я думал будет виден старый экран и т.д. Но абсолютно всё как и раньше. Ставите второй сверху и всё. Удачи
@@andrej7964при сборке дополнительная толщина не сильно парит мозги? Ну в смысле, что винты надо недотягивать и типа кнопки болтаются? На сколько это на самом деле проблема, если ставить новый поверх старого? Спасибо
@@user-zh7cr9yq3v Кнопки не болтаются, при затягивании болтов никаких перекосов или еще чего нибудь...Внешне, да и внутренне разницы не видно...Если б сам не ставил, не написал бы...Я тоже сомневался, пока не поставил...Делайте смело
Super video. A little care and dexterity called for. Hardest bit was replacing plastic in car. £9.59 off ebay; skoda, vw etc are all the same. You pay more than double for the one labelled VW......obviously driving a VW means you're flush. Only worry is it is glued round the edge; how long will this cheap Chinese touch matrix last; compared to the shite OEM VW (chinese) matrix. I have visions of a great stack of touch screens...... Many thanks for great instructions.
Just bought new screen from the link you suggest..£10. Arrived in just 5 days from China to me, that is seriously fast for this time of year! Whole job took 1hr, very simple, works perfectly again! Thank you Duncan and Merry Christmas to you 🙂
I saw one video where they heat it up on a bed then use like string, cotton or dental floss from side to side in a sawing motion starting at 1 corner. Looked very easy once heated.
It really worked for my 2017 VW california. Amazing Duncan! just remember to disconnect the memory reader and not to close the clip the frame with the two displays. You rock!
Great helpful video thanks! Did you have any issues to refit the stereo? I read it may require a code? Also did you need to disconnect the battery at all before removing the radio? Thanks
The cables are a bit fiddly to reattach when putting the unit back in the dashboard. There was no enable code to type. I did not remove the vehicle battery.
I currently have a fully functioning screen besides the top left corner (where the previous station arrow is), any tips for potentially fixing a deadzone? Little gimmicks that might work? Ive noticed some responsiveness when i hard press for a long duration but its inconsistent
Duncan-Thanks for this-Did you stick the new digitizer to the old screen using the attached adhesive strip around the new digitzer screen or just use this as a spacer and leave the new screen loose behind the frame?
So i didn't even bother sticking it down. I thought i'd put it back together unstuck first to see if it worked on and never bothered taking it apart again to stick it down.
Hi, Thanks …so far so good but how did you get the black facia off. Your vid goes from a view of circuit board resting within the facia (while you flick up two hinged connectors)… to looking at the isolated screen. Grateful for the in between step. Do I need to remove the 8 screws in the circuit board?
Sorted… found clip next to SD slot and removed 8 screws. Unfortunately, then had a moment of stupidity resulting in slight tear of gold strip thinking it was redundant! Probably stuffed. We’ll see when screen arrives. Thanks anyway!!
Hi Duncan, firstly this a superb informative video that is easy to digest! Secondly, do you know if the link you provided for this screen would fit a Skoda Yeti from late 2015 unit? I believe my unit in mine is a Armudsen 2?? And yes, it has just started "ghosting"!! I would be able to put this repair on myself. Cheers in advance. Kyle from Scotland.
So if it looks like the same head unit as mine, it probably is. Even if it's not, try taking it apart and see if there's a part number written on the display. Once you have a part number it will be available somewhere online.
Hi Duncan. Thank you for the speedy reply! Yes, it does look exactly the same minus the CD insert at the top. I will check the part numbers. Also let you know the outcome incase you buy a Yeti in the future😊 Cheers.
Hi Duncan, thank you for putting this up, it really is brilliant. I have same issue with a skoda yeti. Could I ask you whether you cut off the ribbon cable from the non functioning screen or does it just 'hang about'? I will be ordering the new screen shortly and was just concerned as to whether the old screen cable would still fit, even though it won't be connected. Many thanks.
Hi John, for the touch sensor on the VW head unit the cable is very thin. I just stuck it down with a bit of tape to stop it flapping about. If it got in the way though, it would have been trivial to cut with a pair of scissors. Note that i'm not replacing the actual screen here but the transparent touch sensor that goes over the top of the screen. If it's actually the screen you are replacing, maybe you can take the old one out entirely? If it's the touch sensor the same as me, i think you'll probably get away with doing the same as i did. If it works on the Yeti, make a UA-cam video about it. Seeing how helpful this one has been has been very satisfying. Good luck!
@@DuncanLaw it is the touch sensor that I'm intent on replacing, just like yours. Its a very similar unit, mine only having one sd slot and no navigation capability. I suspect I need to pull it out to find the model to get the correct touch sensor. Thank you so much for replying.
@@johnbamford203 So mine was labeled with a part number for the whole display. Not just the touch sensor. That did allow me to find a compatible touch sensor though. You can actually see it at time 6:44 of the video. Hopefully yours is the same. You can also see at that time where i've taped the cable of the old touch senor to the back of the screen with a bit of double sided tape and the new one is still free.
great job Duncan. I have the same issue on my Seat Alhambra 2016. May I ask you how to remove the unit (i.e. going from 1:35 to 1:40) ? Thank you very much
So dashboards are held together with stiff clips. It looks like it's all one piece but it isn't. In my van I was able to get my fingers under a bit of trim and popped the first clip. Try anywhere that looks like a groove or 2 different types of plastic meet. I think the proper tool is made out of stiff plastic so it doesn't scratch. Once the first clip is open the rest are easier, partly because you know you are on the right track. Try looking online for information on your model of car. Every model is going to be different.
I've never commented before but Wish to express my gratitude to the UA-camr. The 4S store quoted for $1400 and I followed this protocol to change the touchscreen, spending only $15. I wish you be awarded Nobel prize for this discovery.
I just ordered the part. Any advice on taking out the stereo and putting it back in?
Thanks, saved me hundreds of dollars, almost $2k if I wanted to go through VW.
A few notes:
You will need T6, T7, and T20 Torx screwdrivers, the T20s take the stereo out of the car, the T7 removes the casing, and the T6 is for the circuit board.
He also skips a few steps, presumably because it's hard to do them while holding a phone to record. Only one thing really stumped me for a few minutes until I figured it out:
When you get the part where you are removing the circuit board/screen from the outer casing, there are clips next to the SD card readers that you have to press in order to release the board. You CAN remove the SD cards as he says, but you do not need to. Still, I found it easier to just take them out as this made accessing the clips easier for both removal and replacement.
I spent in total about $25 dollars on this repair, and that cost included a $10 Torx screwdriver set.
Be sure not to overtighten the screws affixing the board to the screen as this will apply pressure to the screen and give you white spots on the screen while you're using it. It's annoying, because by the time you realize you tightened them too much, you've already plugged everything back in.
What a find, thought it would cost me hundreds of pounds , but just like in the video it cost less than 30 with a bit of elbow grease and a couple of hours to do the job. I can't recommend this guy enough. Thank you Thank you.
Thanks so much; I've just spent a good portion of a Bank Holiday Monday successfully repairing the screen on my partners 2016 Yeti with the help of your video. Not only does the head unit now work perfectly, the level of smug satisfaction I've got from fixing a thing properly is through the roof - she's already fed up with me prancing around the house like I'm the god of car audio repairs.
Brilliant cheap and straightforward fix. Been living with stations jumping about and the odd random calls for over 2 years now, but wasn't parting with £800 for new unit. Part came from Aliexpress in less than 2 weeks, 2 hours work this morning and working as new.
Thank you....
Thanks for taking the time to post this. Really easy to follow. I have a Discovery nav (2017 California Beach ) with an ALPS chip set next to the SD Card reader. To remove the screen from the PCB I had to remove both the vertical SD card readers as there’s a small pressure clip on each that needed to be pushed to release the touchscreen. One other build - reset the head unit after reinstalling (on mine it was just pressing the power button and holding for 10+ seconds until the unit restarts. The new digitiser didn’t work until I did this.
Great job Duncan! I was offered a replacement unit by VW for $1700. That included 60% goodwill from them. In other words a new unit with instalation would cost about $4k. I decided for $1700 I'd be better off buying a 3rd party replacement unit -- until I saw your solution. Now after spending less than $20, I have a fully working unit again. Thanks for the clear instructions and the link to the touch screen vendor. WELL DONE MATE!
Same as others on here, I was quoted 1500 plus to replace the unit by the dealership. This cost me about £25, very satisfying repair, many thanks!
Duncan thank you so much for this, many little tips you gave helped massively . Just a couple of things that may improve.
1. Remove the metal shroud totally which gives you almost the extra gap you need to double layer the digitiser.
2.If you follow no.1 then clean both pieces and use the sticky to glue then together.
When reassembled i did the screw up fully bit very minor torque and screen has no white spots or anything else and buttons do not rattle.
the only way you'd know it had been carried out was a slightly dimmer screen.
Once again many thanks , i ordered the same as you from aliexpress for my 6.5 and it came in 10 days and cost £8.50.😍
Thank you so much from Australia..
I learned from your video that the problem could be fixed cheaply and I immediately followed link to order the part from Aliexpress.
Local VW dealer quoted me AUS $3919 ( $3519 for parts and $400 service fee) to replace it for my 6 years old Caddy. Touch screen stopped working a year ago.
The touch screen arrived today from China after 2 weeks.
I also used another video from "neuromangler" for a lot more details in the repairing process.
I ended up spending AUS $20 plus 2 hours of my time. It is now working like a new one.
Huge thanks!!! Duncan!
AWESOME!!!! I got it resolved thanks to your video. It was easy and within 20 minutes I had my VW Passat 2016 stereo functioning as intended. The dealership wanted $800 for a new radio. Thanks again!!!!
Success!
The right half of the screen failed to respond to touch and this fix worked a treat! Struggling to get the trim fitted on again, around the AC controls though. Thanks so much for this!!!!!
Thanks for the vid. As others have said, worked perfectly and saved a fortune.
The only bit that’s missing and that caught me out slightly were the little clips next to the SD card readers. They needed unclipping before the board came away from the screen. Other than that, all fairly straight forward.
Just started experiencing issues with my screen and so glad I found your vid. Replacement screen ordered and looking forward to a fully functioning screen again! Thanks for the vid!
VW told me I needed a new head unit which would cost €2,700! Fixed it myself with the part suggested by Duncan. Thanks Duncan!
This is exactly what I had to do for my 2017 VW Jetta. Your instructions were 100% accurate. Thanks so much. It cost me $25 for the part which was mostly shipping.
Thank you!! This worked perfectly for my 2017 Jetta. Screen only took a week to get here. Mine head unit is a little different as the release tabs are on the inside and I had to remove that small daughter board as well.
I had to run to Home Depot to get a Torx key set, I needed T6 & T8.
I advise anyone doing this to make sure to have all smaller Torx sizes before beginning.
Thank you so much for sharing that fantastic solution. A 15$ job instead of 350$ to replace the screen or 2400$ + labor to replace the radio at the dealer. The most difficult part is to remove the plastic frame around the radio. It helps to have good plastic tools for that.
A great father and son opportunity to repair the unit for £25. Thanks for the awesome post!
Thank you very much Duncan, this has saved me a lot of money as I was contemplating a replacement unit altogether, I bought the screen as per your recommendation and bought some precision torx screwdrivers at a total cost of about £20 for the two items and have just finished the job and put the unit back in my CC and hey presto.....it all works again. Thanks again 💯👌👍
Thank you! I just fixed my broken Jetta radio with this video. Putting the new screen on over the old screen worked perfectly. I'm so grateful. Good job!!!
Strange how everyone’s digitiser goes on the right hand side, isn’t it? Mine too! Wouldn’t have dared to try tackling this without this video. Shame that at the critical bits the video stops and then restarts when the dismantling has been done. However, really useful to show you what you need to do and I understand that when you are trying to video what you are doing you can’t do both at once! Once you’re in there it’s quite self explanatory. A lot of little torque screws to remove but just take a photo at each stage and you’ll know which hole they need to go back in. A bit nerve wracking and of course you don’t know if it’s worked until you’ve put it all back together, but it did so well pleased. Thanks a lot Duncan. Keep up the good work!
Hey there - thank you very much for the guide. I ordered a new screen 9 days ago from your link below ($14 delivered to Sydney), it arrived today and took me 25mins to fit. Its fantastic to have control of my radio after 10 months since the touch screen failed. I've placed this one over the top without breaking into the screen unit like you (@ 5:35). The new screen comes with a glued edge and attaches to the alloy border on the old unit - I needed to remove the glue protection (paper) and place it accurately first time, no second chance. I can now use Android Auto again as was not possible to add a new android auto device without touching the screen (android auto/screen mirror selection) - that's been a major headache for a long time. I'd been quoted $3000+ for a new unit, or $800 for a stolen one with no security codes..... Duncan you're a legend sir.
Thanks for taking the time to let me know! Saving someone else fro the pain i went through trying to work out how to fix this makes taking the time to document it worth while. Thanks!
Thank you for taking the time to do this video. You’ve saved me so much time, effort and money! I did this fix on a 2017 Seat Alhambra with a touchscreen that was partially non responsive and driving me mad. Your fix worked a treat. Thank you again for this!
Hello, i have the same probem in my alhambra.
could you tell me, witch model did you buy ?
thanks
You were the first video I seen that suggested leaving the old screen on. Worked perfect. Thanks. Only thing to add is make sure anyone doing this orders a small precision torex screw driver set along with the replacement screen. Torex head sizes for the internal radio screws were very small T 5 I think. I chanced a small flathead and got away with it luckily.
Thank you very much, Duncan! Very good solution for an otherwise really expensive problem. It took some time for me to find out how to separate the circuit board from the display assembly. There are some plastic clips at the SD-cardreaders.
Thank you very very very much.
they ask 400€ to repair it. I watched your video and I did it myself.
Holey moley! Duncan, I can't thank you enough! The ghost touches / not at all responsive faulty original screen were driving me crazy for about two years, skipping tracks back and forth and dialing extra numbers while talking on the phone. My local dealer said all they could do was to replace the whole unit and quoted me €1100 just for a new unit, with additional labor cost etc. Then I stumbled upon some mail-in online offers, which still were ranging from €300-€450... I was almost willing to save up that money just to get a working touch screen again.
I recently got a new mobile phone - while my old phone always connected automatically via bluetooth the new phone hasn't been paired yet.
Even though it's possible to use the physical buttons to navigate to the bluetooth pairing mode and select a phone, the very last step to confirm a pairing code can only be done via touch screen - and the old one just wouldn't react at all (except for two spots in the very bottom left and right corner - but far away from the confirmation box).
Then, just by chance, this video popped up in my recommendations. I watched it, was very intrigued and mailed the same vendor that you linked to with photos of my unit and he pointed me towards the proper touch screen I needed. I also ordered some tools to remove the faceplate surrounding the radio unit. About 11 days later the new touch screen finally arrived - thanks to this video it was quite easy to follow the steps shown and just put the new touch screen on top - just as @pikey6258 described, I put the screen on the frame of the whole screen unit (not directly on top of the other touch screen inside the screen unit). Half an hour later I was back sitting in my car, really really excited and nervous if this will finally end the suffering of not having a fully functioning radio unit - but then it registered every touch right away and I could access all the menus I couldn't anymore before. It was such a relief!
I could also finally connect my new mobile phone, so listening to podcasts while commuting while be very convenient again!
So thank you again so so much!
Without this video I might have spent 12-15 times more money to get this fixed!
You sir are awesome!
THANK YOU!
❤
Thanks for this video. Followed it with my son and it works! And saved a small fortune. You’re a genius 😁
Fantastic. That saved my 5 year old head unit from going in the trash.
Awesome fix, my Tiguan unit has just started having random fits, bought new sensor panel. Thanks for the video.
Wow, thanks for the video! I'm definitely going to give this a try. My 2016 VW CC's screen started randomly beeping and clicking as if it were being used about two months ago. Completely unable to use navigation or even stay on a single radio station for long periods of time. I didn't even know this was a possible repair option until I found your video. Looks like it'll be around $10 to the US for me, much more affordable than the $1,100 my local dealer quoted me for replacing the entire unit!
Ha! Same story here, bud. Except, they wanted €2000 from us.
Top man, worked a treat! Little tip - I put some foam tape on the backs of the rubber button covers, which removed any rattles. Also left the metal shroud off. Thanks again! Good to have a working radio back. Done in 1hr :)
Hey Duncan, I just had the same problem with my tiguan. Found your posting and followed the link for Ali express. Took 2 weeks, not bad from China! Thanks for the instructions, it really is a straightforward procedure and is now working perfectly. Volkswagon are infuriating! Will not accept the unit is substandard but is repairable and just want to sell you another unit for an unbelievable price. Seems this is happening world over on a regular basis but same old response from VW. Again, many thanks for your research.
My Tiguan is the same, VW said prob be over £2000 for them to replace. It went crazy, first started dialling my contacts randomly, then deleted all radio stations along with icons, then satnav went crazy putting me in middle of Europe! A guy in a repair shop who VW sales rep told me to contact still wanted £400 just to send it off to see what was wrong with it. I'm ordering this, if it works, this guy is a genius! 😁
One of the best youtuber of the world 👍
Je viens d'effectuer la réparation, sauf que je n'ai pas remis le cadre métallique ni le scotch, par choix perso, et ça fonctionne au top, réparation rapide et invisible.
J'ai pris le tactile finition brillante, et c'est parfait à mon goût
Thanks thanks thanks a lot man, i love toi 🥰😁
Thank-you so much for posting this video and the link to Ali Express.I have a 2017 Seat Alhambra fitted with the same head unit and I was quoted over £3,500 (!) to repair or replace the touch screen (probably would have replaced the entire unit). So your tutorial allowed me to fix the faulty touch screen for £12.......RESULT !!
Duncan, I have been searching for a solution for nearly a year - standard "you need to replace it" nonsense. Now it's fixed and fully functional for £11 thanks to you taking the time to explain and share! THANK YOU
Just want to add I've been having the same issue for ages, going to give this a go. Thanks to OP for posting Part Numbers and even a direct link!
Hi there. Would you be kind to let me know where did you get the part? Thanks
@@josevieira422 AliExpress, it's in the video description
Thanks very much for posting this video really useful. I found that once the screws were removed that secure the circuit board, I had to release plastic clip retaining each sd card readers in order to withdraw the circuit.
Hi Duncan, thank you fo posting this video. I have replaced the digitizer on my unit and it's now working perfectly again. Used the the exact one you had refrenced for my 2018 Amarok - MIB STD2 PQ +/NAV
This saved me a fortune!
I bought my Cali aware of this issue from the seller, who took £1500 off the purchase price. VW wanted £2400 saying I needed a new head unit and I was quoted £1250 for a new alpine unit from a car radio specialist.
So I followed Duncan’s video, thinking this can’t work… paid £10.98 for screen, £10 on some torx screwdrivers as you need T10 to remove unit, T8 & T6 to unscrew the unit and it works as it should again, thanks to Duncan.
Hello
Can you advise me please, who to purchase the screen from ?
Okay Briit Girl 55 yrs old. I did it myself - and IT WORKED!! had screws left over tho ! hahaha..
Thank you so much Duncan - Dealer quoted £650 to fix of money I just have not got. .
Now tho'....am very happy! Thank you TONS!
VW Skoda = Feck'em.
Just performed the install and it works perfectly! Just make sure to keep your screws organized. Thank you for the clear and concise instructions. I also bought the same screen off of AliExpress but selected the matte version to keep the same finish as the original screen.
You mean you choose the frosted versión o what? Thank you in advance
@@carlosrafael7904yes I bought the frosted version. It matches the original finish of the screen
This video helped me out tremendously. A few notes for people that are doing this or about to:
1. You do have to remove the SD card readers.
2. When you are putting things back together, you do not need to put the metal shield back on the front of the display, this just adds extra girth with no benefit.
3. DO NOT tighten screws all the way. Tighten them as lightly as you can. Tightening them too much will make the screen go white/light on the sides where the buttons are.
That last point can be an exercise in patience. Tighten, reassemble radio, test. Disassemble, loosen, reassemble and test again until you get it good enough for your liking. The buttons can be a little rattle-y if you leave the screws a little loose, but that I think is a good price to pay.
Good luck guys!
Also, to add to your list, you need three sizes of Torx screws: T20, T8 and T6. The deeper you get into the radio unit the smaller the Torx gets.
Дополню, сорри, что на русском.
Имел сегодня секс с этим процессом.
Выводы:
- Если ставить сенсор поверх старого - будьте готовы к тому что на прямом солнечном свете экран заметно бледнеет, но в общем не критично. Видно нормально, да и прямое солнце светит редко.
- экран начинает не сильно, но отражать. Тоже, чем больше солнца, тем больше бликов. Но тоже не критично.
- причина - воздух между слоями. Почему нельзя сделать «полный-клей» на подобии защитных стекол, как на телефонах - не понятно. Уверен, это сняло бы обозначенные вопросы.
- снимать металлическую рамку экрана - нет никакого смысла, так как экран упирается в лицевую панель именно сенсором, а не рамкой. Высоту «пирога» это не уменьшает совершенно, но рамка, если она есть - хорошо центрует экран в лицевой панели.
- новый сенсор добавляет этой сборке лишних 1,5-2 мм и это действительно проблема. Можно конечно недожать болты, но если плата не станет на свое место, а она не станет, это выльется в следующие проблемы. Кнопки будут болтаться, карт-ридеры уйдут вглубь облицовки, плата будет перетянутая и перекошенная и может даже сломаться, особенно в зоне «крутилок», и вы не поставите не перетянув плату на место верхний металлический щиток этого экранного модуля. А следовательно - не соберете нормально устройство.
- решение есть! Нормально встать плате на место мешает не экран! Плате мешают крепления рамы экрана, которые из-за дополнительной толщины сенсора поднимаются на 2 мм. Сам экран плате не мешает. Он ниже. Нужно эти крепления немного модифицировать, так, чтобы они стали на старое место. Нужно разогнуть эти крепления вверх, расточить отверстия к низу, и согнуть обратно, чуть ниже чем было. Лишнее отрезать. Рама алюминиевая и все это делается аккуратно, но не сложно. В итоге - всё становится на место как положено, «бутерброд» собирается, винты затягиваются, всё на месте, всё готово.
В общем, схема рабочая, но надо иметь в виду первые два пункта. Если вас это не смущает - все это делается за час. Китайцам - отдельное пожелание, сделать всё тоже самое на липучке «полный клей». Цены не будет этому изобретению.
Удачи! 👍🇺🇦
THanks for the tip, found that if the screws aren't tight enough then the buttons are mushy .
Unfortunately reassembled the radio to find (as you say) I've got white spots on the screen. So reassembling it all again now.
Hola, so what is your advice about the correct tight of screws? Thank you in advance!
@@carlosrafael7904 unfortunately, exactly to David's point, you'll get used to taking the front off the radio and plugging it in several times before you get it right.
My 'Radio' button is still mushy and I think two of the plastic standoffs are probably not doing much holding anymore. But my screen works at least.
Just followed this great instruction and fixed my Discover Media Radio! Thank you so much!
Like others, I found this video to be incredibly helpful! Thank you so much for posting it. And shame on Volkswagen for making it necessary. You made it much easier with this video
Perfect guide thanks, just followed! Including removal just under 1hr
Followed your instructions to the letter and it worked. Thank you so much.
Thanks Duncan - a definite wallet saver. Just changed the screen on my 2017 Alhambra. Took a couple of hours and now works perfectly. Your video helped greatly.
Thank you very much, saved me money by watching your video had to watch a couple more to see how to remove the player
Thanks
Thanks Duncan, great video fixed in under 2 hours taking my time with a few cups of tea.
This is so good! Fantastic, just fixed mine and it works perfectly thanks to your video and the links for product! Thanks!
Fantastic video. I
I now have a fully working head unit once again.
Just did this today, thanks buddy I was doubting myself but she worked great!
The video is perfect - I just repaired my T6 touchscreen with a alibaba part from China - works perfect for 13 € - thanks a billion for the video! 👍
It worked for me too in my VW T6 transporter! Easy to do. Great solution….thanks!
Hallo Duncan, herzlichen Dank aus Deutschland für Dein sehr hilfreiches Video und den Link zum Ersatzteil. Die Reparatur ist mit Deinem Video einfach. 😊
Just saved a grand doing this - thank you so much for the guide and the link! Amazing!
What a awesome Job Duncan! Thanks for the help! Worked like a charm!
Das funktioniert. Danke. Der Platz ist knapp aber wenn man die kleinen Torx Schrauben vorsichtig anzieht gehts. Am Ende von aussen nicht sichtbar.
This works. Thank you. The space is bit tight but if you are careful when you fix it back (dont overscrew the small torx screws) then it goes. From outside your see nothing.
Nice video, thankyou. Quite an easy repair, having seen the video, to give me confidence. My ocd would have liked me to remove old screen....
I did attempt it, 5 mins in oven on 80 degrees, but chickened out, too tight/afraid of having to buy new lcd.
This repair cost me about £15 👍👍
Yea, before i realised we don't need to remove the old touch sensor i was going to take the screen into a mobile phone repair shop; They will have the tools and experience for working with glued on sensors.
Thank-you so much for this! After years of putting up with the screen ghosting and not willing to pay £690 for someone to fix it, I found your video through the forum. 30 minutes later and it's all sorted! Thanks again
Dear please tell me is it working good for you. I have also touch problem.
Yes it's working perfectly. Back to normal after the new digitiser was fitted
@@fob3664 No need to remove old touch just by putting new over old ?
Exactly.
There is just enough space for the new one without removing the old one.
Pls where can I buy new one? Thx for answer
Thank you for this video. My screen wouldn’t respond to any commands on one side, weird. Now works perfectly.
Fair play Duncan, and thanks for the video, everything back working as it should and most of all at a fraction of the cost to any alternative
Thank you so much Duncan.......absolutely amazing. Now works perfectly.
THANK YOU SO MUCH. Your video was so helpful to me. I also manage to remove the old touch screen with a hairdryer. 🙏
Oh cool. I presumed it would take more heat than that.
Thanks Duncan, have been dealing with this nonsense for a while.
Me funcionó perfecto para mi estereo de beetle 2017. Gracias. Saludos desde México
Hero, thank you Sir! It was driving me crazy. Hope it lasts fingers crossed.
Can't believe I've just bought the touch screen from Ali express for £1.29, first order 70% off + free shipping! 😮
I never make comments on UA-cam videos. But this one is awesome. Shame on VW for asking for a lot of money for something that I managed to repair for 15€. Many thanks for the tutorial
Same case for me. Thank you very much 🙏🙏
Thank you very much.
I saved 1800 Euros.
It cost me 16 Euros to repair it.
Works perfect on my T6 california ! Thanks a lot !
dude your video works thanks for taking the time to share this did mine in well under an hour
Daniel in Nashville. 2017 VW Beetle vert. Took about 2.5 hours. Ordered the same screen off of ali Baba. Toughest part was getting the whole unit back in as there is little slack in the wiring harness. Note: Cleaned the original screen very well as there was a combination of grime and finger oil all around the edge once the metal frame was off. Wondered if this was cause of issue (right side of screen did not work, left- hit or miss) and if I could just clean it good and NOT put new screen over. Did put new screen over. All who do this need to also have a very clean environment. Clean the screens with sterile water and a microfiber, let dry, and try not to get anything between the two glass screens. I wore disposable plastic gloves and used a antistatic mat to keep things from sticking to the glass. Still, I found a tiny dust fiber in one corner after install and looking at it under a magnifier. Unit works though and wife is happy. This video NEEDS to be relabeled as "VW Discovery Media MIB2 faulty touch screen repair" and you will get a lot of hits. Thank you. Thank you Thank you! Also, separate issue, when I put the V 10 SD card in for navigation update, the screen says" This card has the navigation database. " Then: loading Navigation Database. Then there is a blue circle that spins round and does not stop. Have left for hours. Still just a spinning circle. Any clue as to how long it takes to update the navigation database? I saw a video of someone loading ad there is a progress bar displayed . I don't get that, just the stupid blue spinning circle. Anyone?
I love you. Saved me quite a bit of time and money.
I appreciate you posting this!! It totally works
You have saved me a lot of time and money!!! Thank you so much.
Красава…я не додумался даже что тупо положить новый сенсорный экран на старый сработает. Сомневался до конца. Тема реально работает, по сути всё просто. Только что сам заменил и радуюсь. Респект автору!
это действительно работает?
@@daruksdioma7205 да…я думал тоже что ерунда. А оказалось что без проблем. Я думал будет виден старый экран и т.д. Но абсолютно всё как и раньше. Ставите второй сверху и всё. Удачи
@@andrej7964при сборке дополнительная толщина не сильно парит мозги? Ну в смысле, что винты надо недотягивать и типа кнопки болтаются? На сколько это на самом деле проблема, если ставить новый поверх старого? Спасибо
@@user-zh7cr9yq3v Кнопки не болтаются, при затягивании болтов никаких перекосов или еще чего нибудь...Внешне, да и внутренне разницы не видно...Если б сам не ставил, не написал бы...Я тоже сомневался, пока не поставил...Делайте смело
@@andrej7964 понял, спасибо.
Уже заказал, вот только теперь думаю, трогать ли старый тач.
Super video. A little care and dexterity called for. Hardest bit was replacing plastic in car. £9.59 off ebay; skoda, vw etc are all the same. You pay more than double for the one labelled VW......obviously driving a VW means you're flush.
Only worry is it is glued round the edge; how long will this cheap Chinese touch matrix last; compared to the shite OEM VW (chinese) matrix. I have visions of a great stack of touch screens......
Many thanks for great instructions.
Worked perfectly - thank you very much indeed!
Just bought new screen from the link you suggest..£10. Arrived in just 5 days from China to me, that is seriously fast for this time of year! Whole job took 1hr, very simple, works perfectly again! Thank you Duncan and Merry Christmas to you 🙂
Thanks! Great idea, worked well for me too. 😊
Works perfectly, you can remove the old touch screen just has alot of glue that needs to be removed
Did you remove the old one? If so, how long did you warm it up for and at what heat level?
I saw one video where they heat it up on a bed then use like string, cotton or dental floss from side to side in a sawing motion starting at 1 corner. Looked very easy once heated.
Thank you worked a treat.
It really worked for my 2017 VW california. Amazing Duncan! just remember to disconnect the memory reader and not to close the clip the frame with the two displays. You rock!
Thank you!!! I hope your invested time will be returned to you someday.
Mine just stated ding the phantom touch today. I'll have to give this a go.
Worked perfectly and didn't cost the earth. £13
Great helpful video thanks! Did you have any issues to refit the stereo? I read it may require a code? Also did you need to disconnect the battery at all before removing the radio? Thanks
The cables are a bit fiddly to reattach when putting the unit back in the dashboard. There was no enable code to type. I did not remove the vehicle battery.
I currently have a fully functioning screen besides the top left corner (where the previous station arrow is), any tips for potentially fixing a deadzone? Little gimmicks that might work? Ive noticed some responsiveness when i hard press for a long duration but its inconsistent
Duncan-Thanks for this-Did you stick the new digitizer to the old screen using the attached adhesive strip around the new digitzer screen or just use this as a spacer and leave the new screen loose behind the frame?
So i didn't even bother sticking it down. I thought i'd put it back together unstuck first to see if it worked on and never bothered taking it apart again to stick it down.
Worked for me thx for vid!!!
Hi, Thanks …so far so good but how did you get the black facia off. Your vid goes from a view of circuit board resting within the facia (while you flick up two hinged connectors)… to looking at the isolated screen. Grateful for the in between step. Do I need to remove the 8 screws in the circuit board?
Sorted… found clip next to SD slot and removed 8 screws. Unfortunately, then had a moment of stupidity resulting in slight tear of gold strip thinking it was redundant! Probably stuffed. We’ll see when screen arrives. Thanks anyway!!
Do you know of a way to power on on the bench, or does it require being connected to the vehicle computer to turn on? Thanks.
Might try this on my 2017 Passat 🤔
Hi Duncan, firstly this a superb informative video that is easy to digest! Secondly, do you know if the link you provided for this screen would fit a Skoda Yeti from late 2015 unit? I believe my unit in mine is a Armudsen 2?? And yes, it has just started "ghosting"!! I would be able to put this repair on myself. Cheers in advance.
Kyle from Scotland.
So if it looks like the same head unit as mine, it probably is.
Even if it's not, try taking it apart and see if there's a part number written on the display. Once you have a part number it will be available somewhere online.
Hi Duncan. Thank you for the speedy reply! Yes, it does look exactly the same minus the CD insert at the top. I will check the part numbers. Also let you know the outcome incase you buy a Yeti in the future😊 Cheers.
Hi Duncan, thank you for putting this up, it really is brilliant. I have same issue with a skoda yeti. Could I ask you whether you cut off the ribbon cable from the non functioning screen or does it just 'hang about'?
I will be ordering the new screen shortly and was just concerned as to whether the old screen cable would still fit, even though it won't be connected.
Many thanks.
Hi John, for the touch sensor on the VW head unit the cable is very thin. I just stuck it down with a bit of tape to stop it flapping about. If it got in the way though, it would have been trivial to cut with a pair of scissors.
Note that i'm not replacing the actual screen here but the transparent touch sensor that goes over the top of the screen. If it's actually the screen you are replacing, maybe you can take the old one out entirely? If it's the touch sensor the same as me, i think you'll probably get away with doing the same as i did.
If it works on the Yeti, make a UA-cam video about it. Seeing how helpful this one has been has been very satisfying.
Good luck!
Actually, maybe your Yeti uses the same model of head unit?
@@DuncanLaw it is the touch sensor that I'm intent on replacing, just like yours. Its a very similar unit, mine only having one sd slot and no navigation capability. I suspect I need to pull it out to find the model to get the correct touch sensor. Thank you so much for replying.
@@johnbamford203 So mine was labeled with a part number for the whole display. Not just the touch sensor. That did allow me to find a compatible touch sensor though. You can actually see it at time 6:44 of the video. Hopefully yours is the same.
You can also see at that time where i've taped the cable of the old touch senor to the back of the screen with a bit of double sided tape and the new one is still free.
gracias !!! buen video
good job!!
great job Duncan. I have the same issue on my Seat Alhambra 2016. May I ask you how to remove the unit (i.e. going from 1:35 to 1:40) ? Thank you very much
So dashboards are held together with stiff clips. It looks like it's all one piece but it isn't. In my van I was able to get my fingers under a bit of trim and popped the first clip. Try anywhere that looks like a groove or 2 different types of plastic meet. I think the proper tool is made out of stiff plastic so it doesn't scratch. Once the first clip is open the rest are easier, partly because you know you are on the right track.
Try looking online for information on your model of car. Every model is going to be different.