As you see, You are Connected the Gate Terminal Directly ( Without any Resistor ) with the T1 ( Terminal One ) which have Heigh Voltage ( 220,V ) . So Why the Gate Terminal Not Damage Due to you say,s Earlier that The Gate Terminal should be operated with 01..01.5-V . So what is the logic with them sir .
MY BT 136 Sparked and blasted with high sound, when one wire of AC input given directly on gate. You are using DC power source and DC bulb but not clear the viewers, your power supply (DC) is hidden, you cannot given AC directly on gate without resistance of 100k or above for limiting the current and volt to the gate.
Spot on , bro! There should be adequate warning upfront in the video, on possible dangerous shock, if not done properly.👽 This is not for beginners. Ideally, the bulb ( type, wattage should be mentioned) should be shown mounted on a holder , and 'wire touching' could be via a push switch .
I used BT 136 600E 1250.followed your instruction
some time it work nicely .
Drawing please details
you just gave 220volt ac at the gate of triac to trigger the triac
my question is how much time the 220 volt ac supply take the gate pin?
using the triac the contacts of the ignition keys of lights, motors, etc are not damaged ... very good video .....
one of the best videos /
Could you explain the same with DC, the behavior is different
Excellent. Thanks a lot.
Excellent. Works with 220V from a wall socket and 40W bulb. Thanks.
A Very Clear explanation,Thank You.
How does the gate only handle few milliamps if you’re touching a 12amp line with it?
Good morning bhayya.
When we connect this triac to a ceiling fan, does it need heat sink.? Please reply.
you always need to use a heatsink with BT136
Will this circuit work for inductive load like ceiling fan ?
yes
Can we use this triac in vu units of heavy load like full chain light will glow with music?
You can run anything with a max current load of 4 amperes.
Thank you for the idea, very useful for me
One of the best explanation provided
why need triac if we can direct light to source .. Is triac AC use only not applicable to DC..please..
Thanks for explain of triac working. I want to know that what will be happen if gat connect with T1.
When there's no voltage at t2 how is it working with gate voltage
Make your videos in hindi...it's good for your channel...groth.
thanks
Which type of power supply and voltage you are using in this video
Bt136 a.c. device which operate on a.c. hight volts it gives high current
thank you
As you see, You are Connected the Gate Terminal Directly ( Without any Resistor ) with the T1 ( Terminal One ) which have Heigh Voltage ( 220,V ) . So Why the Gate Terminal Not Damage Due to you say,s Earlier that The Gate Terminal should be operated with 01..01.5-V . So what is the logic with them sir .
😂😂 Right Observation, TRAC damage ho jayega, You can't connect directly T2 with Gate, you should use Resistor
thank you ... nice video
Hi friend
How to add triac to led driver?
connect LED driver(AC) in place of bulb
MY BT 136 Sparked and blasted with high sound, when one wire of AC input given directly on gate. You are using DC power source and DC bulb but not clear the viewers, your power supply (DC) is hidden, you cannot given AC directly on gate without resistance of 100k or above for limiting the current and volt to the gate.
I m using AC power 220V
You connected to live wire, you should connect to neutral...
how much ac supply did you use in this video
220 volt a.c.
thankss.....
Nice working for ac
very good
Comming and going 😁
यह हिंदुस्तान है यहां हिंदी बोली जाती है हिंदी बोलोगे तो ज्यादा लोगों से जुड़ गए और अंग्रेजी बोलोगे तो सीमित हो जाओगे
be safe while experimenting with AC circuits
Spot on , bro! There should be adequate warning upfront in the video, on possible dangerous shock, if not done properly.👽 This is not for beginners.
Ideally, the bulb ( type, wattage should be mentioned) should be shown mounted on a holder , and 'wire touching' could be via a push switch .
BT136 MRP Kya Parega
Rs.5 to Rs.15 : it depends on the shop
When tested with 10amp ac load the triac fused within seconds
When tried with 10amps ac load by triggering with incoming ac volts as shown by you the triac bt139 failed within seconds
For BT136 : max current is 4A with heatsink ..... and 1A without heatsink
Bt136 is a high current device use in a.c. volt hight volt
Its not working.. i tried it..
Change the power input terminals
How to check traic using multimeter
1:07 small bulb 😁
Good
Sir please hindi me samjate to samajme aata.
Koi hindi video banaye. Please
thanks...........:)
Itna simple nhi ho sakta mien kitna try kia
Khalifa video banate hain
Hindustani Hain ya Engrej Bolte bhi nahi aati Hindi bolna sikho
Bhai Hindi mein bol le English tere muh mein fas rahi hai
vi banglai bolan
Pagal Kahi ka
आप की सदस्यता मैंने ली और वापस छोड़ दी क्योंकि आपको हिंदी नहीं आती
english bekar video
Bakbas
very bad
is the AC input to the TRIAC is 230V. CAN IT HANDLE 220V-230V. does it require HEAT sINK.???
Refer to datasheet
www.mouser.com/ds/2/302/BT136-600E-352978.pdf
Yes because this is high power device and high current
Wow, thats a good video. Thanks