That worked like a dream.... I went in with LOW expectations but following your clear instructions it worked first time.... Possibly for the first time ever..... Thank you very much 👍
Tried 3 different videos - the approach shown here was the one which worked for me. Note that the approach was different from the instructions provided with the remote. Video is really clear and specific on steps needed and how you know the programming is working - i.e. what LEDs flash and when. Really useful - many thanks
Thank you so much! I managed to get an universal remote from Aliexpress (not the one you show here) up and running thanks to your video. But strangely: All four buttons seem to be programmed now, but only one is doing anything - and it is NOT the one I pressed during the cloning process. But the main thing is that I now have a working clone!
Great video mate! I followed the instructions that came with the remote and it didn't work. lots of looking around before I came across your that works cheers 🇬🇧
Thanks mate. You made my life a lot easier. Just read the instructions and they made no sense at all. I got the remote to work as I watched your video 👍🏻
Thanks. Two additional tips: Mine would stil not open the garage door, despite the led blinking confirmation. Turned out there was a tiny piece of bare metal wire broken loose from the solder on one side, on the back of the new remote. I soldered it back and now it works fine! I had to 'tune' to the right frequency by turning the tiny screw on the bottom right first though. :)
Just wondering before I pull my elderly neighbours remote apart can you actually change the frequency on these remotes if that’s what I take ‘tune’ as or you just having a laugh
Thanks so much. Lifesaver ! In my case I only got one to work. The other would not reset . The button solid Flash after reset on every button . Edit : got it to work. Must be something about the timing issue with resetting
Thanks. Yes it took me along time to figure it out myself. Back when I sorted this, there was not one solution. Glad this helps people :) hopes you liked and subbed to push it back up the list :)
Thanks, that got it going. But A would only open the door so programmed C straight after in same way and now A opens and C closes, I'm happy with that.👌
Cheers. Maybe your door master controller memory is full. you can clear it and start from scratch. should work. UA-cam it :) I think I did a video years ago that had how to reset and clear the master controller memory.
Champion, I was following OEM instructions and nothing was working till I saw your video and cleared the remote. Followed OEM instructions again and boom... working remote 👍
Great ... MAybe you should share you one that was not working here and I will add it into my intro speel above, may work for the ones that my method does not work
Lorsque je veux réinitialiser la télécommande en appuyant sur les touches A et B ==> la lumière reste fixe. Y-a-t-il une autre possibilité de réinitialisation?
je ne suis pas sûr. Je n'ai pas eu ce problème. Je pense avoir posté un autre lien dans la description pour une autre méthode que j'ai trouvée. Cela peut vous aider.
Is there any possibility to erase the code from the original remote when programming a new remote? I have only one original, and I don't know how to reprogram again if needed. 🙄
I am glad.... Yep I struggled to find the way to do it ... so figured it out and shared it so you all can get the benefit. hope you liked and subscribed
Got mine to work thanks to your video, but the range on it is crap. I have to be almost on top of the garage door mechanism for it to work? The original one still works from metres away?
Thanks for the great and easy to follow video. Set mine up in minutes after watching your video. Works so well. Thanks for taking the trouble to make this very helpful video. Australia
get a genuine one then as your signal strength sounds like it has reached it range. easiest way to find your range is to slowly walk toward the door and press until the door reacts.
You Tube it. I believe there are or 3 different methods for the same looking device. If you do find it, let me know and I will post it in the title notes. and may even add a little bit of an explanation at the end of this video.
Hi mate..thanks for the video, as my same remotes are crazy.I followed yur reset ode, howeer, theywill no reset. I get th same led light flashes like you do, but they never reset....any more clu?
Please, yes for extra links. I have followed the tutorial exactly. The broblem that keeps reoccurring, is when actually holding down the original remote button and the clone one. When simultaneously pressed, I get the clone led flash a few times, but it will never do the final flash to say it has accepted the code Unfortunately, this same thing happens every time. I do hold the remotes next to each other, and have rotated the original remote to every single side, as well as to the two faces of the remote to try find the signal, all to no avail.The clone resets perfectly, as shown by pressing a/button at same time, and then releasing b 3 times. It will simply not indicate the led flash that the code has been read. Thanks
Well, after months of trying, I cannot get these to work on a Firmamatic remote controlled garage door. I still find, that on some occasions, it appears, like the video, that the buttons do not have anything stored. However, a long press of the buttons, which is needed to get my control unit to recognise the transmitting remote, that all the a b c d buttons all show a red light on a long press, and not on with a quick press. I tried so many times, I got the remote batteries go flat. Tried on three units as per the video, without luck. Does anyone use them on anything else, so I can try to confirm they are simply not compatible with Firmamatic?? Thanks for the help.
Hi, not sure if someone has the same issue. I have the same garage fob, but a few weeks after programming it's not working and I have to do the programming again. I even bought two and they both lost programming at the same time. Does anyone know what could be the reason?
Can someone help please I have pressed both button which did the reset I have clone 1st and 2nd button from the original remote, which worked My first try with the gate was a success, both opening and closing However this was the first and last time it worked, the remote still works, blue light still flashes upon press, but the gate do not respond at all PS:The original remote is still working normally Thank you
The duplicate remote programmed using your video was perfect. However it works only 1 time and then has to be re programmed and process repeated. Any solution for this ?
@@rent2ownnz thanks for this. However it works for the first time I press the cloned remote . Should I try pressing again, it does not work. If it works once it has to keep working. Could it be that it’s not able to store memory
I have same problem. I thought remote was broken so I bought few of them from diffrent producers but still works only once. I tried to code it in motor but still works only once😐
I did all the same. Reset, clone. Lights the same blink, after clone steady on on press, but remote doing nothing. On old remote the same MHZ 433,92. Where can be trick?
Yo!! Like the video but HTF do you get 'em cleared of factory code? I have tried pressing A & B simultaneously but the light just continously lights intermittently.
You press A & B together, then leave A pressed, release B, and press B 3 times. He clearly explains this in the video, however I can't get anything else to work 😔
Same.. I have mine for years. Until now i really need it for my remote car replacement. The instruction to clear the code is different from other videos i've found years ago. Once again, thank you sir westy 👍
Unfortunately, I did not. After following the manufacturers programming method and also every other tutorial on the internet, I ended up getting refunded from ebay. Sorry I couldnt be any help. Good luck. :)
Hi maybe someone know how to solve my problem. I have the same universal remote but after copying the code it works only once and after that one shot it stops working. I tried few other remotes and same story.
Steps: ================================ |Clear existing Memory Settings| ================================ 1. Hold down the A & B Button (the two closest to the LED Light) 2. While Holding down Button A (Left) Press (Slowly) button B -right one, 3 times 3. Then Release Button A. Now no button presses will operate the light (LED) ================================ |How to Set New Learning Code | ================================ This is a 2 Stage Process: ========= |STAGE 1| Programming New REMOTE ========= 1. Get old door opener and the new non-programmed one close to each other 2. One the old Remote that works, hold down the button that works on the door 3. Now Press and hold the button (The LED will Flash a few times and then be raon the new remote you wish to operate your door with. 4. Hold this button down until the LED light goes Solid 5. Stage one Complete ========= |STAGE 2| Syncing to Door Master Controller (If Above does not work) ========= 1. Put Garage Door Master Controller into learning mode and wait till it is in listening mode (Each type is different = refer to your owners manual) and then press the button you have configured.
Thanks for the video. If I don't have the remote, can I buy one on eBay and ask the owner of the garage door the provide me with the frequency and a code? But, then, how could I program myself the remote? Sorry, lots of questions.
Really happy I came accross your video but this still didn't work for me as my garage control unit does not recognize the new remote. Which is the same remote as the one you have. Also my garage opener is a Chamberlain but guess a different model from yours. I got a ML500. Any suggestions or is it perhaps that this remote will simply not work for this model?
Hi There, Try doing to the Door opening controller (On the door itself) and press your buttons on the remote.... can you see the light rapidly flashing on the control unit? if so, it is seeing your remote , but just needs to be #CODED# into your controller. try the last part of my instruction on how to do that. - see how you go
Westy's How To Guides Thank you for your reply. I have noticed that when I use the original remote the LED on the control unit flashes rapidly but it does not flash rapidly when using the new remote. I guess that answers my question then, the control unit does not see the remote. Will have to look into another model.
Hi. I have that exact remote just arrived. I press both A and B buttons together. I get one quick light then a constant flickering light. Not 3 lights then off. Any ideas that I could try? Cheers.
I got the same remote as in the demo. I programmed it up and it works. I had to hold the remote one metre away from the opener, cos the remote batteries were so flat. Off to get some new batteries.
I followed all instructions and it shows that my remote is linked. But still doesnt open garage. Have tried doing it on the actual garage door as last part instructed. Flashes as if synced. But still doesnt work 2 open garage :( please help.
Hey man, just bought a couple but when trying to clear them, the led on both of the clone remotes constantly flashes and I’m unable to clear or sync them up, any idea how to fix this?
mate the last part of your vid is exactly what im looking for. But I didn't quite get what you mean. I seemed to have copied the program onto my universal key but it didn't work on the door. Does the last part of your vid mean that I should do the clone process close to the operation unit? or putting the operation unit under learning mode? really appreciate if you can clarify on that!
"Does the last part of your vid mean that I should do the clone process close to the operation unit? or putting the operation unit under learning mode? really appreciate if you can clarify on that! " Look up your Garage door control unit manual and work out how you put it into learning mode. Once in the mode. Press your new remote that you programmed in my above video and Viola!
Press and hold DOOR CODE button once Select one of the four buttons on key transmitter you wish to use to control the door. Or the button on the end of the manual release cord. Setting the Transmitter to Operate the Door The opener can only operate from transmitters that have been programmed into its receiver. The receiver needs to learn the codes of any transmitter that will be used with the operator. Up to sixty four (64) codes can be stored in the receiver’s memory. a. Ensure the button cover has been removed (see Electrocution caution) and the opener is turned on. b. Press and hold the DOOR CODE button. The DOOR CODE LED will illuminate and beep to indicate the opener is in Code Learn mode (Fig. 8.1). c. Press and hold the transmitter button that you want to control the door for two (2) seconds, pause for two (2) seconds, then press the same button again for two (2) seconds and release. d. Release the DOOR CODE button. e. Press the transmitter button to test.
thanks dude. really appreciate your detailed explanation. it will defs help other people stuck in a similar situation. but i guess im done cuz its a gate for the entire flat's parking area. i just moved in and i thought i could just copy my flatmate's key but if i open that control unit chances are i get taken by the police... but anyway really useful content keep it up fam
That worked like a dream.... I went in with LOW expectations but following your clear instructions it worked first time.... Possibly for the first time ever..... Thank you very much 👍
Tried 3 different videos - the approach shown here was the one which worked for me. Note that the approach was different from the instructions provided with the remote. Video is really clear and specific on steps needed and how you know the programming is working - i.e. what LEDs flash and when. Really useful - many thanks
Appreciate the feed back, am really glad it worked for you. Took me a long time to figure it out by trial and error.
Thank you so much! I managed to get an universal remote from Aliexpress (not the one you show here) up and running thanks to your video. But strangely: All four buttons seem to be programmed now, but only one is doing anything - and it is NOT the one I pressed during the cloning process. But the main thing is that I now have a working clone!
Best video for getting these remotes working, thank you.
Köszönjük!
I watched many videos and this is the one that works. Thanks!
Perfect - worked first time with my NECo key fob. Saved myself £40 😀
Nice one! good stuff :)
Great video mate! I followed the instructions that came with the remote and it didn't work. lots of looking around before I came across your that works cheers 🇬🇧
Thanks mate. You made my life a lot easier. Just read the instructions and they made no sense at all.
I got the remote to work as I watched your video 👍🏻
The best easiest tutorial i ever seen. Thank you very much
Thanks. Two additional tips: Mine would stil not open the garage door, despite the led blinking confirmation. Turned out there was a tiny piece of bare metal wire broken loose from the solder on one side, on the back of the new remote. I soldered it back and now it works fine! I had to 'tune' to the right frequency by turning the tiny screw on the bottom right first though. :)
Just wondering before I pull my elderly neighbours remote apart can you actually change the frequency on these remotes if that’s what I take ‘tune’ as or you just having a laugh
@@simonkirton8521 I believe they support 2 freqencies, 430 and 320 or something like that. So it's likely some kind of binary switch.
Thank you. Mine came without instructions. Works perfectly now.
You're welcome!
Great vid, mine works great. Would you consider a video on how to change the battery on this badboy?
Thanks so much. Lifesaver ! In my case I only got one to work. The other would not reset . The button solid Flash after reset on every button . Edit : got it to work. Must be something about the timing issue with resetting
must be kaput ... probably a broken wire
Thanks man, finally got the bloody thing running 😀
Thank you very much... With your explanation works excellent...You saved a lot of time...
I am very grateful....
Thanks. Yes it took me along time to figure it out myself. Back when I sorted this, there was not one solution. Glad this helps people :) hopes you liked and subbed to push it back up the list :)
Thanks, that got it going. But A would only open the door so programmed C straight after in same way and now A opens and C closes, I'm happy with that.👌
Cheers. Maybe your door master controller memory is full. you can clear it and start from scratch. should work. UA-cam it :) I think I did a video years ago that had how to reset and clear the master controller memory.
I got a couple I had trouble programming them too. After a year still going strong.
Hay any tips I did what you did it didn't work so tried to program of the main unit but that didn't work either maybe duds?
Not sure ... have a look at some of the previous comments there are a few methods to do these units.
Loving the content westy!
Thanks my man
The best and simplest instruction - thank you thank you😊
Cheers. This has saved me twice!
Champion, I was following OEM instructions and nothing was working till I saw your video and cleared the remote.
Followed OEM instructions again and boom... working remote 👍
Great ... MAybe you should share you one that was not working here and I will add it into my intro speel above, may work for the ones that my method does not work
@@rent2ownnz I didn't make a video mate, all good your video was what I needed to do 👍
Only video that worked for me👍🏻 thank you 🙌
Thank you. I never got a manual when I purchased these. This video is very helpful and they work great. Thank you for the 411.
Most welcome
Lorsque je veux réinitialiser la télécommande en appuyant sur les touches A et B ==> la lumière reste fixe. Y-a-t-il une autre possibilité de réinitialisation?
je ne suis pas sûr. Je n'ai pas eu ce problème. Je pense avoir posté un autre lien dans la description pour une autre méthode que j'ai trouvée. Cela peut vous aider.
Yep...this works, just ended 6 months of faffing about with other remotes...(but there again I am a slow learner!)
Lol, life is about learning. pay it forward :) Glad it worked for you
Thank you sir, your method worked great in New Zealand. Jai hind
Is there any possibility to erase the code from the original remote when programming a new remote? I have only one original, and I don't know how to reprogram again if needed. 🙄
Thanks for this, instructions were vague but got the remote to work thanks to your video!
Thank you! I just did it and worked like a charm!
I am glad.... Yep I struggled to find the way to do it ... so figured it out and shared it so you all can get the benefit. hope you liked and subscribed
All well and good if it flashes 3 times but what about when the light just flashes rapidly when pushing A and B
Got mine to work thanks to your video, but the range on it is crap. I have to be almost on top of the garage door mechanism for it to work? The original one still works from metres away?
faulty remote
Worked perfectly, Thankyou
When I hold down A & B buttons the (LED) light stays lit doesn't blink?
Take a look at my Video Notes. There are 2 Links of other methods if mine does not work. Come back to me if you succeed
Cheers
Westy
Great job thank you for your help.😊
Worked with 4003 Rev2.1 🙂. Note to release B and click three times was the main issue I had. Was able to clone from TX3312 B1.0. Thanks 👍
Thanks for posting a video that actually works for these remotes! I really appreciate all of the research that you did to figure this out too.
Thanks for the review. I am happy it worked for you. CHEERS WESTY!
Yep Nar, the clear out bit works but the learning bit was a flop.
Thanks this really helped and it worked perfectly.
Thanks for the great and easy to follow video.
Set mine up in minutes after watching your video.
Works so well.
Thanks for taking the trouble to make this very helpful video.
Australia
More than welcome. Glad it helped.
The problem is when you are in 30meters away to your door the clone remote did not work
get a genuine one then as your signal strength sounds like it has reached it range. easiest way to find your range is to slowly walk toward the door and press until the door reacts.
Cheers mate for your help. Good video, great help👍👍
Mine looks like the same but doesn’t do the three blinks and I wonder how to make it work.😢
You Tube it. I believe there are or 3 different methods for the same looking device. If you do find it, let me know and I will post it in the title notes. and may even add a little bit of an explanation at the end of this video.
@@rent2ownnz Thanks for reply. I did have searched and watched more UA-cams but no luck yet with those not blinking like mine.
what if the LED doesn't flash when I press and hold both A&B?
^^^
How would you know if your remote device is 315mhz, 433mhz or 330 mhz?
written on it. or on the the inside (Normally a sticker) or you can get a frequency scanner and press a button and see what frequency it is emitting.
Hi all, i cant erase function. Press a and b together but dont stop blinking. Is there any solutions?
Hi mate..thanks for the video, as my same remotes are crazy.I followed yur reset ode, howeer, theywill no reset. I get th same led light flashes like you do, but they never reset....any more clu?
Hi, Have you tried following the instructions in the description? I have linked 2 other videos that may help at the top as well you you.
Hi - you could try the description notes and I have also 2 other you tube links that may work to help you out.
Please, yes for extra links. I have followed the tutorial exactly. The broblem that keeps reoccurring, is when actually holding down the original remote button and the clone one. When simultaneously pressed, I get the clone led flash a few times, but it will never do the final flash to say it has accepted the code Unfortunately, this same thing happens every time. I do hold the remotes next to each other, and have rotated the original remote to every single side, as well as to the two faces of the remote to try find the signal, all to no avail.The clone resets perfectly, as shown by pressing a/button at same time, and then releasing b 3 times. It will simply not indicate the led flash that the code has been read. Thanks
Well, after months of trying, I cannot get these to work on a Firmamatic remote controlled garage door. I still find, that on some occasions, it appears, like the video, that the buttons do not have anything stored. However, a long press of the buttons, which is needed to get my control unit to recognise the transmitting remote, that all the a b c d buttons all show a red light on a long press, and not on with a quick press. I tried so many times, I got the remote batteries go flat. Tried on three units as per the video, without luck. Does anyone use them on anything else, so I can try to confirm they are simply not compatible with Firmamatic?? Thanks for the help.
Hi, not sure if someone has the same issue. I have the same garage fob, but a few weeks after programming it's not working and I have to do the programming again. I even bought two and they both lost programming at the same time. Does anyone know what could be the reason?
Can someone help please
I have pressed both button which did the reset
I have clone 1st and 2nd button from the original remote, which worked
My first try with the gate was a success, both opening and closing
However this was the first and last time it worked, the remote still works, blue light still flashes upon press, but the gate do not respond at all
PS:The original remote is still working normally
Thank you
Thanks a lot brother from greece
No problem😉
Super work brother . Saved me a tonne of time. Big ups from Ireland 🇮🇪
Great, glad it helped you out.
Hi. My remote is continuously flashing and no combination of keys can stop this. Do you know what i can do?
I saw another vid that showed how to clear out the program but it didn't work. Yours did! Thank you so much!
glad it helped you out
But how do I program the remote i have but only one buton, I dont wanna lose any other i already have programed ?
The duplicate remote programmed using your video was perfect. However it works only 1 time and then has to be re programmed and process repeated. Any solution for this ?
Hard reboot and then clear off any memory on the garage door controller itself. Then try it.
@@rent2ownnz thanks for this. However it works for the first time I press the cloned remote . Should I try pressing again, it does not work. If it works once it has to keep working. Could it be that it’s not able to store memory
I have same problem. I thought remote was broken so I bought few of them from diffrent producers but still works only once. I tried to code it in motor but still works only once😐
On the larger remote which is the button to close the door?
the biggest button
@@rent2ownnz but that's the button that opens it for me. It doesn't close it
Could you make a tutorial to replace the batteries for this exact model? Thank you
Hi There, Which model? the old one? or the new one?
I did all the same. Reset, clone. Lights the same blink, after clone steady on on press, but remote doing nothing. On old remote the same MHZ 433,92. Where can be trick?
Yo!! Like the video but HTF do you get 'em cleared of factory code? I have tried pressing A & B simultaneously but the light just continously lights intermittently.
Same problem here, still looking for a solution...
You press A & B together, then leave A pressed, release B, and press B 3 times. He clearly explains this in the video, however I can't get anything else to work 😔
Hi Westy i tried everything you have in the video but still not work i have a merlin garage door any other ideas i could try thanks Rod.
Hi Rod, is it the correct frequency remote for the door itself?
Great demo mate, unfortunately my remotes just keeps flashing red rapidly when I press A and B
There are a few ways to do it... See if you can you tube another method.
My problem was not pressing them at exactly the same time.
I’ve tried this Di many times! When I press a & b together the led just flashes fast ..what am I doing wrong? 😩
@@Wen-hz9mb again, press the *exact* same time
thanks . had the same problem . remote has been laying in the car for 6 months . now working thanks to you. cheers
Same.. I have mine for years. Until now i really need it for my remote car replacement. The instruction to clear the code is different from other videos i've found years ago.
Once again, thank you sir westy 👍
I'm getting the light flash for 1 button but it's not connecting to door🤔 Ant thoughts anyone?
If you read the instructions in the description, you will get your answer :)
@@rent2ownnz it's not pairing with the door
Thank you so much.
Much appreciated 😊
Thank you. Very helpful.
When I press and hold a and b I get a continuous red light!
Hey. When I follow the first step to clear codes. I hold A+B, (3x Flash) release B, press B x3 and nothing happens. Any ideas?
Same issue here!
Have you solved this as I'm having the same issue...
Unfortunately, I did not. After following the manufacturers programming method and also every other tutorial on the internet, I ended up getting refunded from ebay. Sorry I couldnt be any help. Good luck. :)
Cheers Westy, I was getting close to the end of my rope! Now working perfectly thanks to your video.
Hi maybe someone know how to solve my problem. I have the same universal remote but after copying the code it works only once and after that one shot it stops working. I tried few other remotes and same story.
i would say you may need to clear you main
controller memory
Thanks, it's work for me
You really helped me out man
You are more than welcome. Glad it worked for ya
It helps me alot 😍😍😍
Thank you for your instruction. My remote finally works now 👍
Is it the same process for a gate remote to.
When I hold down both buttons it stays solid. Nothing I've tried makes it blink.
Steps:
================================
|Clear existing Memory Settings|
================================
1. Hold down the A & B Button (the two closest to the LED Light)
2. While Holding down Button A (Left) Press (Slowly) button B -right one, 3 times
3. Then Release Button A.
Now no button presses will operate the light (LED)
================================
|How to Set New Learning Code |
================================
This is a 2 Stage Process:
=========
|STAGE 1| Programming New REMOTE
=========
1. Get old door opener and the new non-programmed one close to each other
2. One the old Remote that works, hold down the button that works on the door
3. Now Press and hold the button (The LED will Flash a few times and then be raon the new remote you wish to operate your door with.
4. Hold this button down until the LED light goes Solid
5. Stage one Complete
=========
|STAGE 2| Syncing to Door Master Controller (If Above does not work)
=========
1. Put Garage Door Master Controller into learning mode and wait till it is in listening mode (Each type is different = refer to your owners manual) and then press the button you have configured.
Thanks for the video. If I don't have the remote, can I buy one on eBay and ask the owner of the garage door the provide me with the frequency and a code? But, then, how could I program myself the remote? Sorry, lots of questions.
I got a Morton 10 by alpan garage door , will it work for it?
Not sure... Only one way to find out.
Who is Gairedge?
Really happy I came accross your video but this still didn't work for me as my garage control unit does not recognize the new remote. Which is the same remote as the one you have. Also my garage opener is a Chamberlain but guess a different model from yours. I got a ML500. Any suggestions or is it perhaps that this remote will simply not work for this model?
Hi There,
Try doing to the Door opening controller (On the door itself) and press your buttons on the remote.... can you see the light rapidly flashing on the control unit? if so, it is seeing your remote , but just needs to be #CODED# into your controller. try the last part of my instruction on how to do that. - see how you go
Westy's How To Guides Thank you for your reply. I have noticed that when I use the original remote the LED on the control unit flashes rapidly but it does not flash rapidly when using the new remote. I guess that answers my question then, the control unit does not see the remote. Will have to look into another model.
Hi. I have that exact remote just arrived. I press both A and B buttons together. I get one quick light then a constant flickering light. Not 3 lights then off. Any ideas that I could try? Cheers.
you could try this ua-cam.com/video/l-k_XvkZ0jE/v-deo.html
or this
ua-cam.com/video/RM_xgNsP4sQ/v-deo.html
I got the same remote as in the demo.
I programmed it up and it works.
I had to hold the remote one metre away from the opener, cos the remote batteries were so flat.
Off to get some new batteries.
Mine just drains the new battery as soon as I install it works for a Lil bit then the light gets week then goes out
I followed all instructions and it shows that my remote is linked. But still doesnt open garage. Have tried doing it on the actual garage door as last part instructed. Flashes as if synced. But still doesnt work 2 open garage :( please help.
Thank you! Your video brought me further.
This one works for me. The other when you have to pouch a and b together not. Thanks!
Glad it worked for you :}
Hi, thanks a lot for your video and it has been very helpful as I managed to clone it perfectly. Thanks again.
Hey man, just bought a couple but when trying to clear them, the led on both of the clone remotes constantly flashes and I’m unable to clear or sync them up, any idea how to fix this?
Same problem here
Same to me , did you find where’s problem?
Thank you very much ... I've cloned mine
Bloody legend mate❤️
Thanks
No problem
Hi Westy, nice video, really ahndy, can you give the link where did you buy those Garage Door Opener - Universal Remote?
thank you, Australia
Can i program the RC like when i press A to open when i press B to close ?
It helps , but i must see this video for several times , because I can not understand British accent. 😬
It is a New Zealand Accent ... Thank you kindly :)
Great! Thanks a lot!
Thanks 🙏🏼 so much I bought the exact same remote and all buttons flashes and now its all good peace
great! thank you.
mate the last part of your vid is exactly what im looking for. But I didn't quite get what you mean. I seemed to have copied the program onto my universal key but it didn't work on the door. Does the last part of your vid mean that I should do the clone process close to the operation unit? or putting the operation unit under learning mode? really appreciate if you can clarify on that!
"Does the last part of your vid mean that I should do the clone process close to the operation unit? or putting the operation unit under learning mode? really appreciate if you can clarify on that! "
Look up your Garage door control unit manual and work out how you put it into learning mode. Once in the mode. Press your new remote that you programmed in my above video and Viola!
Press and hold DOOR
CODE button once
Select one of the four buttons on
key transmitter you wish to use to
control the door. Or the button on
the end of the manual release cord.
Setting the Transmitter to Operate the Door
The opener can only operate from transmitters that have
been programmed into its receiver. The receiver needs to
learn the codes of any transmitter that will be used with the
operator. Up to sixty four (64) codes can be stored in the
receiver’s memory.
a. Ensure the button cover has been removed (see
Electrocution caution) and the opener is turned on.
b. Press and hold the DOOR CODE button. The DOOR
CODE LED will illuminate and beep to indicate the
opener is in Code Learn mode (Fig. 8.1).
c. Press and hold the transmitter button that you want to
control the door for two (2) seconds, pause for two (2)
seconds, then press the same button again for two (2)
seconds and release.
d. Release the DOOR CODE button.
e. Press the transmitter button to test.
thanks dude. really appreciate your detailed explanation. it will defs help other people stuck in a similar situation. but i guess im done cuz its a gate for the entire flat's parking area. i just moved in and i thought i could just copy my flatmate's key but if i open that control unit chances are i get taken by the police... but anyway really useful content keep it up fam
VERY NICE THANKS
Ta, but mine after a while always stops working