Hello, Thank you for all your work on these boards. I have a board that has a GD32F130 chip but it doesnt quiet match any of the layouts on your site. I was hoping you could point me in the right direction? I cout send you a picture of the master board if I knew where to send it. Thanks in advance
Nice work!!! Question - If I use ready binaries "hoverboard 2.2 single Dummy.bin" on my PCB 2.2 on SLAVE board - is this should work OK on slave board? What should was behave motor ? -
I think the motor should spin forward and backward. The on off button will not work and the slave board might need the master-slave serial cable to turn on. I do not have my 2.2 test setup nearby for the next 2-3 months. But you might ask for help in the GitHub 2.2 issue.
@robodurden :-) solved - i checked again and error was on mybside :-) I have 2.0 version acording to "photo guide" - but i found on pcb 2.2 number and by my fault Inloaded 2.2 firmware :-) stupid error. Now working OK pcb both słave and master. Comparing to oryginal program motor work louder ua-cam.com/users/shorts1i7h1ylVZNc?feature=share
can i keep hoverboard features if this is flashed, so can i make it self balance after flash or do i need to use outside imput from arduino? and is this foc control or? the 1 board ones are foc, but i do not understand if this is foc, now the new boards on aliexpress say they have foc control from stock...
This Gen2.x is not FOC and needs Arduino/Esp. And no hoverboard mode any more. Some Gen1 firmwares try to offer a hoverboard mode. But I do not like stupid fun projects. Bye !
how to define HANDLE remote,,. what start about 0,8V and end in 2,49V... to keep ToRQUE seting in freewheel mod.. cause there is no proper scale f compensation i figt that part like 7days and still not set.. and ON and OFF cause shift of aproximation..
Search AliExpress for 'dcdc cc'. If you have a 24V source or a 16-19V notebook power supply, you can choose a cheap step up or LCD boost/buck converter.. Most cheap step down are not suitable for 10s battery :-/
Thank you so much. Your dedication to this project is truly admirable. In challenging times like these, your work not only offers a glimmer of hope but also inspires us to focus on positive things and overcome the hurdles we face. Your effort is a reminder that there's always something good to look forward to. Please keep up the fantastic work! @@robodurden
Hello, Thank you for all your work on these boards. I have a board that has a GD32F130 chip but it doesnt quiet match any of the layouts on your site. I was hoping you could point me in the right direction? I cout send you a picture of the master board if I knew where to send it. Thanks in advance
Start a new issue on my GitHub repo. There you can add high resolution photos.
Nice work!!! Question - If I use ready binaries "hoverboard 2.2 single Dummy.bin" on my PCB 2.2 on SLAVE board - is this should work OK on slave board? What should was behave motor ? -
I think the motor should spin forward and backward. The on off button will not work and the slave board might need the master-slave serial cable to turn on. I do not have my 2.2 test setup nearby for the next 2-3 months. But you might ask for help in the GitHub 2.2 issue.
@robodurden :-) solved - i checked again and error was on mybside :-)
I have 2.0 version acording to "photo guide" - but i found on pcb 2.2 number and by my fault Inloaded 2.2 firmware :-) stupid error. Now working OK pcb both słave and master. Comparing to oryginal program motor work louder
ua-cam.com/users/shorts1i7h1ylVZNc?feature=share
can i keep hoverboard features if this is flashed, so can i make it self balance after flash or do i need to use outside imput from arduino? and is this foc control or? the 1 board ones are foc, but i do not understand if this is foc, now the new boards on aliexpress say they have foc control from stock...
This Gen2.x is not FOC and needs Arduino/Esp. And no hoverboard mode any more.
Some Gen1 firmwares try to offer a hoverboard mode.
But I do not like stupid fun projects.
Bye !
how to define HANDLE remote,,. what start about 0,8V and end in 2,49V... to keep ToRQUE seting in freewheel mod.. cause there is no proper scale f compensation i figt that part like 7days and still not set.. and ON and OFF cause shift of aproximation..
Maybe better speak your native language and i let Google do the translation :-/
Any recommendations on current limiters.
Search AliExpress for 'dcdc cc'.
If you have a 24V source or a 16-19V notebook power supply, you can choose a cheap step up or LCD boost/buck converter..
Most cheap step down are not suitable for 10s battery :-/
hello there, i have two motherboard layout with gd32f130 do you have any github link for this? thank you!
github.com/RoboDurden/Hoverboard-Firmware-Hack-Gen2.x/ if yours is not one of the currently 16 layouts, start a new issue and upload photos .
Thank you so much. Your dedication to this project is truly admirable. In challenging times like these, your work not only offers a glimmer of hope but also inspires us to focus on positive things and overcome the hurdles we face. Your effort is a reminder that there's always something good to look forward to. Please keep up the fantastic work! @@robodurden