Yikes! I'm now afraid to take mine apart knowing what might be lurking inside! I have two channels with no effects send and don't know if it's just the pots or if there's damage on the board. Guess I'll have to brave the dust bunnies and find out.
Hi, thank you for watching ☺️ This powered mixer have a cracking sound on the channel volume, some are loose. I replaced them all to be able used it feels like brandnew ☺️
Hi bro, the problem with the shutdown after 2 seconds of turning on is just a ground defect in the console, or it could be another problem, thanks for your time brother, thank you so much.
@@giovannimercado3704 Hi, thank you for watching ☺️ Yes, one of the reasons for shutting down is the grounding between the panel and the power supply. Another reason is fault on the amp board or on the power supply board.
@@ARTaudio440 hi bro, I exchanged it with a other operatonal power supply and the problem continúes (it turns off after a second), where You recommends that i check the amplificación stage.
@@giovannimercado3704 Hi, make sure you have a ground wire connected to the panel and power supply. Once you confirm the ground connection and the issue is still the same then I suggest letting the qualified technician check the amp.
tengo un aigual y enciende pero se apaga a los pocos segundos, cambie dos trasnistoes de salida que estabn en corto y sigue igual, ya medi y no tiene DC en salidas, tampoco marca ningun corto, podria orientarme? gracias amigo
Hi, thank you for watching ☺️ Try this. Disconnect the power supply to the amp board and put a ground wire connected to the panel board and power supply board then turn on. If the unit works, re-connect the power supply connector to the amp board and check it again. If it still shuts off, possibly the amp board still has a problem.
@@ARTaudio440 There is a flat tape and the black, blue, red, orange cables, to do the test that you mention, which cables do I disconnect, thank you for your support
Mil gracias ....algo más podría i dicarme en q color de los cables están los voltaje se lo agradecería mucho esq mi equipo se le daño la fuente y no conozco los voltajes ....podría ayudarme
@@auroramoreno9549 Hola, si la salida es buena, lo más posible es que el fallo sea el interruptor de pad o el IC OP-AMP para el preamplificador de canales. Puede aplicar WD40 en el interruptor de la almohadilla. Requiere una solución de problemas profunda. Si se hace lo anterior y aún no hay sonido, verifique los 15 voltios negativos y los 15 voltios positivos. Verifique también que las conexiones a tierra del panel a la fuente de alimentación estén conectadas correctamente.
Yikes! I'm now afraid to take mine apart knowing what might be lurking inside! I have two channels with no effects send and don't know if it's just the pots or if there's damage on the board. Guess I'll have to brave the dust bunnies and find out.
@@glennray1901 Hi, thank you for watching ☺️ Possible reason might be the control, op amp IC or corrotion on the board.
Interesting video!
Q1 What was the problem with this powered mixer?
Q2 Why did you replace some potentiometers?
Kind regards from Mexico!
Hi, thank you for watching ☺️
This powered mixer have a cracking sound on the channel volume, some are loose. I replaced them all to be able used it feels like brandnew ☺️
Hi bro, the problem with the shutdown after 2 seconds of turning on is just a ground defect in the console, or it could be another problem, thanks for your time brother, thank you so much.
@@giovannimercado3704 Hi, thank you for watching ☺️
Yes, one of the reasons for shutting down is the grounding between the panel and the power supply. Another reason is fault on the amp board or on the power supply board.
@@ARTaudio440 hi bro, I exchanged it with a other operatonal power supply and the problem continúes (it turns off after a second), where You recommends that i check the amplificación stage.
@@giovannimercado3704 Hi, make sure you have a ground wire connected to the panel and power supply.
Once you confirm the ground connection and the issue is still the same then I suggest letting the qualified technician check the amp.
Me gustaría saber cuál es el voltaje de salida hacia la amplificación
Hi, thank you for watching ☺️ 66 volts possitive and negative
Ok exelente video.ocupo el diagama😊ke ago
Hola, genial! Gracias por ver☺️
tengo un aigual y enciende pero se apaga a los pocos segundos, cambie dos trasnistoes de salida que estabn en corto y sigue igual, ya medi y no tiene DC en salidas, tampoco marca ningun corto, podria orientarme? gracias amigo
Hi, thank you for watching ☺️
Try this.
Disconnect the power supply to the amp board and put a ground wire connected to the panel board and power supply board then turn on. If the unit works, re-connect the power supply connector to the amp board and check it again. If it still shuts off, possibly the amp board still has a problem.
@@ARTaudio440 There is a flat tape and the black, blue, red, orange cables, to do the test that you mention, which cables do I disconnect, thank you for your support
Me puedes ayudar con el número de este relay azul please?
Hola, déjame comprobarlo y comunicarme contigo. ¡Gracias por ver!
Estou com esta mesa com a fonte queimada
Hi, thanks for watching.
Qual parte foi exatamente queimada?
Se quemaron los componentes.Q406 y407.r423 está r.se kemo x completo.ke valor es.?
👍👍
Thank you
Mil gracias ....algo más podría i dicarme en q color de los cables están los voltaje se lo agradecería mucho esq mi equipo se le daño la fuente y no conozco los voltajes ....podría ayudarme
Hola, gracias por mirar.
El azul es para V-66.00 El naranja es para V+66.00 El negro es tierra.
Mi consola Yamaha emx312sc prende pero no suena
Hola, gracias por mirar.
El posible problema es el regulador ic., ya sea positivo de 15 voltios o negativo de 15 voltios.
@@ARTaudio440 y amigo la salidas están buenas
@@ARTaudio440 una pregunta cuál es
@@auroramoreno9549 Hola, si la salida es buena, lo más posible es que el fallo sea el interruptor de pad o el IC OP-AMP para el preamplificador de canales.
Puede aplicar WD40 en el interruptor de la almohadilla.
Requiere una solución de problemas profunda. Si se hace lo anterior y aún no hay sonido, verifique los 15 voltios negativos y los 15 voltios positivos. Verifique también que las conexiones a tierra del panel a la fuente de alimentación estén conectadas correctamente.
Amigo ya los recibíce y están buenis