Wonderful explanation. Reading all the dimensions in ASME B16.20 was very difficult to visualize. You have made it much simpler. Moreover, thank you for dismantling the SPW gasket. Helped to better understand it's construction.
Amazing.You have explained this video very well with clear explanations which I have never seen before in any site. please make more videos about gasket. Some time purchased spiral wound gasket without inner ring. But the connect line is requirements of FBE inner coatings In cases if we are using gasket without inner ring . The fluid service exposed to flange. I hope there are two solution either flange surface should be FBE or should be purchased spiral gasket with inner ring. However we need your advice about this issue.
As per ASME B16.20, Inner rings are required for the below conditions: i) When PTFE is used as a filler material ii) Based on size and rating combinations (in general above 600#) iii) Recommended for Vacuum service
No, we should not use, because while tightening flange bolts, moment will be generated in flat face flange and it may crack because in most of the cases flat face flanges are of cast iron which is brittle.
@@gourisankarsamanta7670 thanks for your reply!! My flange is gun metal flat face Which is not brittle. I believe crack will not occur in gun metal flange however off course bending moment will be there. So I am in confusion whether should I use this gasket or not in flat face. I read somewhere on internet that we can use it in both flat face as well as in raised faces flanges. Please suggest your opinion.
Thank you, sir, for educating us. A word of appreciation from Nigeria
Beautiful presentation.
All your videos are of immense use to any piping engineer.
Very informative. Your intent for sharing knowledge is really praiseworthy.
Wonderful explanation. Reading all the dimensions in ASME B16.20 was very difficult to visualize. You have made it much simpler.
Moreover, thank you for dismantling the SPW gasket. Helped to better understand it's construction.
Very precise explanation ....Thank you very much sir
Videos are very good ,more informative about ping thank you
Amazing.You have explained this video very well with clear explanations which I have never seen before in any site. please make more videos about gasket. Some time purchased spiral wound gasket without inner ring. But the connect line is requirements of FBE inner coatings In cases if we are using gasket without inner ring . The fluid service exposed to flange. I hope there are two solution either flange surface should be FBE or should be purchased spiral gasket with inner ring. However we need your advice about this issue.
Thanks for this nice video please provide videos about flat and RTJ gaskets.
Very Informative. Many thanks.
Thank you sir..!!
Wonderful explanation.
Good
it was the best education. thank you
Very informative...thanks
Sir for 30" shall we use graphite filler 3.2 mm thick for spiral wound gasket? Sir Please clarify me about graphite filler thick with respect to size.
Sir....synthetic Fibre with inner ring gasket as per 16.21 ...can you please explain
I request you on behalf of all your subscribers to please post more videos.
Amazing
fusion bonded epoxy coating for piping( FBE)
Sir please make the video on non metallic gasket
Please mention in your next video that no inner ring is required up to what sizes. Thanks for your information.
As per ASME B16.20, Inner rings are required for the below conditions:
i) When PTFE is used as a filler material
ii) Based on size and rating combinations (in general above 600#)
iii) Recommended for Vacuum service
hello Sir
can we use spiral would gasket in flat face flanges as well?
No, we should not use, because while tightening flange bolts, moment will be generated in flat face flange and it may crack because in most of the cases flat face flanges are of cast iron which is brittle.
@@gourisankarsamanta7670 thanks for your reply!! My flange is gun metal flat face Which is not brittle. I believe crack will not occur in gun metal flange however off course bending moment will be there.
So I am in confusion whether should I use this gasket or not in flat face.
I read somewhere on internet that we can use it in both flat face as well as in raised faces flanges.
Please suggest your opinion.
@@vikrambar Gun metal is soft and malleable having mainly Copper and Tin.
Spiral wound gasket can be used for gun metal flat face flange.
@@gourisankarsamanta7670 appreciating your prompt reply, thanks!!
Please explain flange isolation kit in next video if possible. Thanks sir
Thank you.
👍
এর দাম কত
Red Bull