I think it will reset irrespective of trip condition persisting or not. Say, after first i/p sets the trip which will make or to 1. This will disable all ands including the first. So you no longer have set bit
Hi Rohan, If any one of the condition fails then that will be captured by SR flip flop which is successor node of AND gate. So even if input changed the output of SR flip flop will not change untill operator gives Reset command from HMI. Please watch the practical demonstration strats from 9 min 20 sec and see that your doubt clears or not. If it doesn't please comment again. Thank you
Your video is great, I'm from Vietnam, I need your help, I am studying about Centum CS3000, I have a problem, I need to track the tank, when the acid level inside the tank is higher to set it up, I want to warn it by use "buzzer stop key" on Centum CS3000's keyboard. Let help me, Please!!!
Sir. if several alarms occur at the same time and IPs are in an abnormal state and a reset is performed, then it seems to me that the next trigger of another IP may work
In case of power failure (To control system or Trip solenoid valves) machine should be safe, it's more dangerous if machine didn't trip. Can cause damage as well as outage. But if it trip due to fail safe scenario, only some power generation loss will happen but machine will be safe.
Thanks
Good work.., appreciate your efforts., try to show an example of PCDI block config. Modbus channels controller etc in EPKS.
In future I will upload a video on procedure of establishing the third party communication by in EPKS.
good logic of first out turbine pump trip
Please make one video on flip flop block and turbine governor logics
Sir plz make more videos on logic control...
I think it will reset irrespective of trip condition persisting or not. Say, after first i/p sets the trip which will make or to 1. This will disable all ands including the first. So you no longer have set bit
Hi Rohan,
If any one of the condition fails then that will be captured by SR flip flop which is successor node of AND gate. So even if input changed the output of SR flip flop will not change untill operator gives Reset command from HMI. Please watch the practical demonstration strats from 9 min 20 sec and see that your doubt clears or not. If it doesn't please comment again.
Thank you
@@teaminstrumentationcontrol4006 sir, I got it now, as observed in video first out was resetting momentarily.
@@teaminstrumentationcontrol4006 sir can you Give your number
Your video is great, I'm from Vietnam, I need your help, I am studying about Centum CS3000, I have a problem, I need to track the tank, when the acid level inside the tank is higher to set it up, I want to warn it by use "buzzer stop key" on Centum CS3000's keyboard. Let help me, Please!!!
Superb
Thank sir
Team Instrumentation dear sir pls upload video about logic of auto start auto stop permissive using control block in theoretical like this
Ok Yogesh, We will upload one video on ur mentioned request.
Sir please making and uploading DCS logic functions block.
Great..
Dear sir without sr flip flop block pls explain
Sir. if several alarms occur at the same time and IPs are in an abnormal state and a reset is performed, then it seems to me that the next trigger of another IP may work
sir plzz updating dcs logic diagram
is this Set Priority
Why for failsafe condition the trip condition is logically 1 or true??
In case of power failure (To control system or Trip solenoid valves) machine should be safe, it's more dangerous if machine didn't trip. Can cause damage as well as outage. But if it trip due to fail safe scenario, only some power generation loss will happen but machine will be safe.
@@teaminstrumentationcontrol4006 thanks for ur swift response....got ur point mate...u r doing a great job keep it up man😊😊
pleas explain logic and or oxr how to work
It's explained in this video only. Please see it again. Thanks
and there is 'first out' block in epks.
Gg we want more videos
Thanks