Honda Ruckus performance CVT transmission kit
Вставка
- Опубліковано 28 вер 2024
- BUY IT NOW:
www.rollingwre...
Budget NCY Transmission kit:
www.rollingwre...
Rolling Wrench has put together this bolt on perfomance CVT transmission kit for your Honda Ruckus (this fits all Honda Ruckus's from 2003 to 2011 GET motor). This kit comes pretty well assembled (check out the picture). This kit takes no time at all to install and offers a big power gain for the money. This kit will come with a belt, clutch, spacer, variator, variator slider guides and Varitaor rollers. You will be re-using your variator fan and both Clutch and variator nuts. What makes this kit so special? The clutch has been outfitted with performance clutch springs, performance secondary clutch springs, the clutch has larger clutch pads, a performance secondary slider and is also much lighter. The varitor is teflon-coated to keep debris from building up in return keeps rollers from flattening, not to mention this variator is much lighter. A lighter CVT allows lighter rotating mass, this give you better performance. This is the only performance bolt on CVT we know of for the Ruckus!
we have two different types of clutch bells. the one in the video is with a open face variator. if you run the cover the clutch bell is still performance, just not with the cooling fins do to fitment
Rolling Wrench ATV Scooter & Motorcycle
I know this video is pretty old but will you restock these anytime soon? Been planning to buy it but doesn't seem like it'll come back
Nice video. How reliable would you say CVTS transmissions are. I’ve read that they are unreliable and expensive to repair in cars. I’d assume the same for scooters?
How fast did the ped go after putting the variator kit on it ?
How fast does it go after installation?
Malossi Variator Installing for honda ruckus ? It comes with 2 Black Spacers / Washers ! 1 Large 1 & 1 Smaller 1 ! But my instructions are so small I can Not read them ! can you please tell me were they go ? Thanks you Very Very Much Thanks George
Excelente vídeo, felicitaciones.-
I already have a Polini variator. Can you just buy the clutch without the other stuff?
I have a 2013 eace supper b09 scooter,no top speed on this scooter,what can you do to help?soom say 5 gram fortop speedthank you
for how many kilometre cvtbelt should be changed
What RPMs is this setup tuned for?
no grease on the variator rolls?
"this fits all Honda Ruckus's from 2003 to 2011 GET motor" what about for the 2012 model with stock motor? I'm looking to upgrade
Ty G GET motor is the same as stock. It's just another name for it. Buy happily!
Damn the "Happy" comments
@Rolling Wrench - Can you give some rough #s to us regarding the different in top speed before/after this kit has been installed?
Also, I've already got a Polini variator on the way - still interested in the clutch and weights though - can you sell me the kit minus the variator?
Does this work for the honda ps 125
lol, this is probally more reliable then the Nissan car cvt
is this kit for nsp50 ruckus?
3 years late but yeah
why u take the kickstarter off its useless
We have the 2020 Ruckus, we did exactly as you did, x3, the clutch was extremely hard to open to add the belt (for my grandson, 25) you made it look much easier. Could the clutch be faulty? It does happen on occasion. The issue we are having is lost performance, also the spacer is getting chewed up. We are experienced, what could be the issue? Is the spacer NOT needed on the 2020 Ruckus? I am not finding much information on this issue, I did find some info on battlescooter.proboards.com/thread/3383. Thanks for any help!
He doesn't reply much
will this work with a 2017 Ruckus ? What increase in performance can be expected. i.e. top speed
Nice video. Does the CVT cover fit back over the new clutch bell?
@4:27 Him: the only thing we’re gonna be using is THIS NUT!”
Me: Yo!!! Pause! Put a Pause on that bro!
Excellent video, simple steps looks like a great job. Thanks!!
*_2 Questions:_*
*1.* Will your Clutch Bell work with an Anklebiter CVT Cover?
*and 2.* With Dr. Pulley Sliders now being a part the Transmission Kit, do you have a slider weight setup that will work well for a rider +200lbs?
It will work with all get motors, it will work for you.
purchased n installed with the cvt cover from ruck shop and used the 5g n 6g rollers i love it dude excellent n i love the new all black clutch bell. thanks
I'm *much* larger than the average rider (6'10" 240). Are the supplied slider weights going to be appropriate for my size?
Let us know in the notes when you order we will put slightly lighter sliders in the kit for you.
Did you order this? Did you see any increase in performance?
Matt Heald
Try 8 grams first, then 9 Good luck.
Hi what makes this cvt.kit h.y. PO? Vs stock? What is the cost 2023?
Every time I click on one of these vids, I wait to hear about the new setup... WHAT are you trying to achieve with this setup...not one person mentions what the "Performance" gains are with a different setup. Are you trying to hold a low gear longer? Are you trying to get more top end? WTF is the point of the new setup??? Not one word is said about what the new CVT is going to, or trying to do...I find that extremely Odd.
He says it right after a minute in, faster take off and higher top speed. Did you even watch longer than 8 seconds?
I watched the whole thing unfortunately... must have missed it.
We know, your time to become aware will come..
1 min 10 secs. he states that improves take off and higher top speed. As to other comments about "more than fucking aware" There is no lower gear to hold longer. It's just one gear. It's a CVT... there are no gears. Come on Son!
SquillyMon you should just delete your stupid comment, save everybody wasting time reading your foolishness
The parts in this video are different than the parts shown on your web page on your "Honda Rukus/Metro Allready Assembled CVT Transmission Kit" as Listed in your performance parts. This video is accesable on your page when you cick on the CVT Kit. You show using the stock Drive face but the kit comes with the Gold colored lightened Drive face. The clutch bell is also different. Why? Also I cannot get the splined round ratchet part to go on the shaft far enough to engage the ratchet starter. (wont go on far enough. )The rear wheel is not on so I took the radiator off so I can hold the flywheel secure with a 17 mm socket on the nut. Im going to try tighten the Drive face nut that holds the washer on to the ratchet starter that holds the Drive face against the drive face boss to squish the belt to take up the slack. Dont know if this is going to work but I think it will. Your showing using different parts can cause problems as specific parts, specs, etc. are required.
Is the new belt any longer or shorter than the factory Ruckus belt?
Hey what are the expected gains
DOES ANYONE KNOW HOW TO GET THE FINAL DRIVE SHAFT OUT that the wheel bolts on to there is nothing online for it i mean nothing i think its a c clip ??? but i cant see it anywhere on the short side maybe under the seal on the long side ??
dude. YOU INSTALLED THE OLD VARIATOR COVER. THAT COVER HAD A WELDED IN RESTRICTION SPACER! YOU WILL NEVER ACHIEVE THAT NEW CLUTCH POTENTIAL. GRIND DOWN THE VARIATOR COVER (BELT RIDE SURFACE SIDE) TO A SMOOTH PLANE -SHAVING OFF THE SPACER. DRAW A MARKER LINE ON THE BELT SURFACE OF THE VARIATOR TO RECORD BELT TRAVEL ON THE VARIATOR SIDE. ON THE CLUTCH SIDE, ENSURE THE BELT SEATS FULLY DOWN ONTO THE SHAFT. THIS WILL ENSURE FULL BELT SURFACE USE THROUGHOUT THE POWERBAND.
Is there a kit to make the ruckus manual?
so THATS how you put a belt on. Me i would just struggle like crazy trying to get it wrapped on. totally not realizing i could just bring in the clutch -__-
i have a 2003 metro. would this kit work for it? also i am kinda a bigger guy 6,4 230 pounds is ther any where i can get a little heavier springs for a metro?
We have used this on metro scooters as well. It works great, however the belt is not going to fit. We would need to find you another belt.
Hello bro, my motorcycle is a Honda click125i, but every time I start to go ,the engine will feel shakes. May I ask which part has problems? Thank you
I did the polini vareator with the 5.6 rollers bike does a easy 45 mph plus.
There’s too much noise coming from clutch box in my scooter . I already changed clutch shoe and belt but still noise coming .will you tell me what to do?
This roller & bushing please put spacial grease
could you fit a polini variator in a standard gy6 A or B case? I hope this question makes sense. Thank you for your videos #SuperInformative
No need for deep 8mm socket. Regular works too.
True
thank you for the actual how to. not just a skim over. keep it up!
Hey hey! Recently got myself a scoot and looking into making some changes to the CVT! I have myself an electric impact driver but doesn't seem to be strong enough to get the variator nut off from the factory. Any suggestions to get the variator nut off or should I invest in a higher performance impact driver? Thanks for the amazing informative videos!
You could try using a variatior tool to hold the pulley still and then use a socket wrench to remove the nut. It might help to tap on the wrench a bit with a block of wood or rubber mallet.
CVT Mirip punya honda vario ( INDONESIA) GOOD JOB Mr. 😁
i was hoping to order the whole assembly kits to build this in my hometown , how to order?
Please help. Lol i want to mod my ruckus were can i buy this in canada
Do you have a performance clutch for PCX150?
is that the jog reaR PULLEY PLATES?
THANKS CHEERS
Will an open face cvt cover work with this upgrade?
Hey .... What about a kit for the "Big Ruckus" units.
what does it cost? my metro goes about 35 with my 6' 4" body on it. any idea were i can get a heavier rear spring for a 2003 metro?
Topeka Kansas
Amazon
Do they make a kit like that for the Zuma?
the background music is SO annoying.
ROLLING ROCK 🪨 🎶FROM ROLLINGWRENCH..🎶
My Mz moskito special edition top speed 150kmh
is this suitable for honda click 125i sir?
will this work on a 2022?
Yes. All rucks are the same from 2002-2022
Hey man were can i buy this kit in canada?
Any videos on install and tuning the 20mm carb you have. I am interested. I have heard they are a pain but nice once dialed in. How much with weather influences the tune. I am in Oregon. Rain, cold, summer and more rain? Thank you.
I don’t have a video yet. That’s what I was kinda waiting on before I put this video out. They can be tricky to tune. If it’s in your budget I have a Plug & Play EFI system that works on the stock GET motor. It’s a 34mm throttle body. You will get the same performance or better than the 20mm carb, but with flawless running. It auto tunes to the atmospheric pressure. This is great for your area. Price is $630, comes with everything and the hand tuner to fine tune. No computer needed and comes with a nice base tune.
@@RollingWrench Is there a link to this product? I have some more question on the EFI system. I will wait to check it out 1st then Email you instead of here lol. Is this system on your site?
Vernon Hochstetler I haven’t released it. I currently have this system on only 4 other GET rucks. Runs great. I need to wrap up the GY6 system on the site then I’ll move on. But I would be happy to sell you a system
What will the new topspeed be with the new kit? :)
Robin Eriksson
Most likely 5 to 7 mph, get a CDI w/rev limiter,
Missing some of your shenanigans but this was a great instructional video. Thanks!
Thanks josh!
This kit is exactly what I've been trying to find! I am looking at it on your website, and I am not seeing an option to select slider weight size...
Our CVT kit is ready to go. We have spent hours tuning this kit so the buyer can just install it and go! I hope this helps :-)
Our CVT kit is ready to go. We have spent hours tuning this kit so the buyer can just install it and go! I hope this helps :-)
will it fit a metropilitan jazz 2003
Thats the grand axis 100 engine?
what's the size of the spacer?
Will this fit 2005 honda metropolitan?
Yes
Why dont put some grease oil in variator?
Not a good idea, if grease gets on the belts that’s a bad thing
piagio block
?
Nice,
thanks sir
can you still use kit with cvt case cover.
Lawrence Co yes you can :-)
Better then the Polini or Daytona Drag?
Still use with the NCY CDI?
perfect work ;)
Does the kit work for the 2017 ruckus?
Yes 👍🏻
What about the 2019-20 ruckus
@@mindrunner18 it works on all ruckus’s 03-22 and probably future models not yet released.
@@mindrunner18 2022 too?
Today, the belt of my Zoomer/Ruckus exploded. I took it apart and I couldn't believe my eyes. The belt had almost no "teeth", they were all gone. The belt was just a bunch of wires and some teeth.
Luckily, I was "just" 5 kms from home and the temperature was just 33 degrees celsius. :)
Pedro Gordinho the kind of belt with which i am aquainted is good for 15,000 miles and mine was 11 years old and gave up the ghost at 15,500 miles.
you should of mentioned that it depends on how much you weigh.. pretty important ..
Isn't that like fuckin obvious? It's a scooter. Don't ride it if you weigh more than 200lb. They are meant for active people in shape not blimps
+James Jacobs. what? hahaha 200 lbs guy can ride, theres jets that goes up to 100 and bigger weights/slidders 😂 i ride with others and there was a 200+ guy riding one and hitting 60. nice troll though... 😂
+Joshua Moss Let me reiterate. Yes you can ride a ruckus and weigh 200+lbs. The ruckus just wasn't designed to hold that kind of weight for its speed output. It was designed for skinny Asian drivers not overweight Americans. Do you see my point?
+Joshua Moss Btw, I hate how your average American needs to stretch the ruckus out to drive comfortable. Just consider yourself blessed if your short & lightweight. It's no wonder the ruckus is popular with females
Do you have a kit like this that will fit a 2016 49cc TaoTao?
witout cover this is not good the engine can breake in half
no it wont brake just chace of stuff going inside cvt case.