there are some flaps that back the coil over decoiler, the position of those flaps changes anytime from 1 roll to other...then the alignment between coil & die changes often. another reason we have to keep it far is that it is hard to synchronize the speed of decoiler and the feed in press. longer distance makes a buffer for this. linear speed of unrolled material slows down as roll is spent but press keeps a constant rhythm.
Three years ago I purchased it from Ebay for $250. It was a rare opportunity. I did not see similar offer since then. However, you might build an Arduino controlled system yourself doing similar job.
@pontian16 No it is 1mm thick Iron. There is no particular reason for setting it apart from punch machine. We could have kept it closer. Next time I will try it closer.
Than you for your visit and your nice comment. Actually, when we Operate it, I stand there and watched it an hour. It was combination of, I wanted to make sure it did not malfunction and enjoyment.
This is very old machine and it was in working condition, I purchased it from eBay for $250 (USA). I paid extra $100 for a valve that is attached to the press. I was lucky to find one. If you look up to eBay for "pneumatic feeder" you may find something to buy in there. I do not now the cost of new ones, but I am seure that they are above $3000 or more. My friend still use the one you see in the video.
Hy at the end of the video... You should roll the rest parts it can be useful for other applications, ventilation systems, on planes to solidify the separations between bigger parts
A re-coiler or even scrap cutter at the end would be useful. Wouldn't want to pick that scrap up off the floor. Also the clamps used to hold die-set down although working are not appropriate.
The tonnage of the press is 30, which is considered a small press; the maximum thickness to be punched hole would be dependent on panch circumference. The Air pressure used in this system was six-bar, and it was a very old compressor. The punched hole diameter seen in the video is 12 cm. The plate's thickness is 1 millimeter.
ohh..i thought you want to cool it or something, but the rolls don't seem to have heaters though..btw, i like your videos, it kinda help me in my studies, hope you can post lot more vid in the future.
We use in my factory different kinds of feeder but decoiler/straightener is kept far from press.I don't know the "science" behind that but: it is hard to align rolls with dies, then longer distance minimizes the potential angle between coil & die.We keep the guides in the die as tight as possible.If material comes with a deviation, it gets stuck.Our dies/coils are hard to align due to different dimensions/location over press & decoilers usually have a screw to fit inner diameter of rolls. TBCont
This is a pneumatic punch press feeder. 10 years ago, I paid $250 and purchased it from eBay as a gift for my friend. You can cut up to 1.5mm thick metal strips.
That I don't know. My friend has big compressor in his factory and they use so many pneumatic equipment and pressurized air was coming from a central compressor which was very large.
Hi~ my name is HJ. I'm a technical sales man for used press machine and NC levelling feeder in Korea. Press machine, feeding machine, milling, lathe, grinding machine, forklift. I handle all press related machines. If you want to import these machines from South Korea, please contact me. I hope to have a good relationship with you someday. Thank you!
I don't know who made this product and I don't have it somewhere near to me to check it. I purchased it from eBay for a gift to a friend of mine. It was $250 and I consider it as rare opportunity.
Finally one where the work isn't thrown in a heap on the floor after every step.
there are some flaps that back the coil over decoiler, the position of those flaps changes anytime from 1 roll to other...then the alignment between coil & die changes often. another reason we have to keep it far is that it is hard to synchronize the speed of decoiler and the feed in press. longer distance makes a buffer for this. linear speed of unrolled material slows down as roll is spent but press keeps a constant rhythm.
Three years ago I purchased it from Ebay for $250. It was a rare opportunity. I did not see similar offer since then. However, you might build an Arduino controlled system yourself doing similar job.
@pontian16 No it is 1mm thick Iron. There is no particular reason for setting it apart from punch machine. We could have kept it closer. Next time I will try it closer.
Thank you for the vid I can watch it all day, in a strange way it is relaxing.
Than you for your visit and your nice comment. Actually, when we Operate it, I stand there and watched it an hour. It was combination of, I wanted to make sure it did not malfunction and enjoyment.
This is very old machine and it was in working condition, I purchased it from eBay for $250 (USA). I paid extra $100 for a valve that is attached to the press. I was lucky to find one. If you look up to eBay for "pneumatic feeder" you may find something to buy in there. I do not now the cost of new ones, but I am seure that they are above $3000 or more. My friend still use the one you see in the video.
Bonecos
Hey awsome demonstration but how did you set the pitch
Hy at the end of the video...
You should roll the rest parts it can be useful for other applications, ventilation systems, on planes to solidify the separations between bigger parts
como le hace para que las.piezas queden arriba y no caigan hacia abajo al momento de troquelar
No, I meant metal sheet rolls.
A re-coiler or even scrap cutter at the end would be useful. Wouldn't want to pick that scrap up off the floor. Also the clamps used to hold die-set down although working are not appropriate.
Yes, scrap cutter would help a lot. Now they use servo driver which includes also scrap cutter.
A mecânica é muito bonita fui preparador de prensas muito tempo
Hi Niket, Go to Ebay and search for "Punch Press". You may find what you are looking for.
What is the punch force tonnage?what maximun rhickness of steel plate can be punched?what size or type of compressor needed?thanks
The tonnage of the press is 30, which is considered a small press; the maximum thickness to be punched hole would be dependent on panch circumference. The Air pressure used in this system was six-bar, and it was a very old compressor. The punched hole diameter seen in the video is 12 cm. The plate's thickness is 1 millimeter.
Onde compro estampa de pregos telheiros para prensa excentrica ?
This machine is available along with small die also
Operation name
ohh..i thought you want to cool it or something, but the rolls don't seem to have heaters though..btw, i like your videos, it kinda help me in my studies, hope you can post lot more vid in the future.
We use in my factory different kinds of feeder but decoiler/straightener is kept far from press.I don't know the "science" behind that but: it is hard to align rolls with dies, then longer distance minimizes the potential angle between coil & die.We keep the guides in the die as tight as possible.If material comes with a deviation, it gets stuck.Our dies/coils are hard to align due to different dimensions/location over press & decoilers usually have a screw to fit inner diameter of rolls. TBCont
Thank you.
I need your WhatsApp number
Which please
sorry, i view in mobile....is that aluminum?..why the distance so long from the rolls to the punch machine?
Sorry, You refer to recycle sheet by casting ??
Schéma électrique d'une presse mecanique a commande pneumatiques
What's price many,
10 years ago I paid $250, I am sure that it may be more expensive now.
Is it possible to make two pieces in one stroke by the help of die???
yes
What is The Price Of Machine? N How Much Thick Metal We Can Cut in It !
This is a pneumatic punch press feeder. 10 years ago, I paid $250 and purchased it from eBay as a gift for my friend. You can cut up to 1.5mm thick metal strips.
Cost kitni h feder ki
hi may i know the cost of this machine
Beautiful
Thank you.
Başarılı bir çalışma olmuş, tebrikler..
Machine name?
Pneumatic punch video and details
Hai I want this type of machine for belt conveyors, rollers bearing housings, what is the cost
contact us no
guru nanakautocom@gmail.com
+919646549568
9597708197
Has anyone previously or currently ran an ST 1225?
did you use pneumatic cylinder for this? wats the bore and short size used?
I purchased pneumatic feeder from eBay. I don't know exact bore size but I guess it is 50mm. Stroke goes up to 200mm adjustable with stoppers.
Thanks and how much capacity of air compressor used for this? 2 HP?
That I don't know. My friend has big compressor in his factory and they use so many pneumatic equipment and pressurized air was coming from a central compressor which was very large.
I want to contact you to order the product
Good feeder and press
Τρόμος ξύλου
go for auto servo fidder
Very nice👍🎤
Thank you for the lovely comment.
مرحبا كم سعر خاذي المكينه
I want this machine how do you got
I purchased it from eBay a long time ago.
Please send me your zig zag servo Roll feadar stainless steel coil circle cutting machine video and details
Can you Suggest the company that can manufacturer this for just circle cutting
yesss i can help you...
lots of that can make high speed for your requirements
Cetakan nya full speed boz
Please tell me your location, i need such type machine
Máy này giá bằng nào tiền và mua ở đâu ai biết chỉ cho mình nhé
0985790381
Its bottle middle bottom
KO I now dai dekhu
sir i need this machine
do u need feeder?, contact us no
guru nanakautocom@gmail.com
+919646549568
Global Nature Agro hey where are you from.
I need this machine
프레스영상 잘보고 유튜브 친구맺고 갑니다 허니비코리아 놀러오세요
잘보고 갑니다 ~ ^^
you can save your westage
Yeh ban Kiya Raha hai
poszukaj czegoś z podajnikiem na paski ;)
Hi
How are you
Good, Thank you for asking.
@@mekanizmalar where are you from
@@raheelahmad8460, I live in the USA, originally from Turkey.
@@mekanizmalar ok thanks
@@mekanizmalar friends with me
Me Kam kar sakta hu
Praveen Agarwal ambica matal works moradabad INDIA
Rise of the Machines
Hi~ my name is HJ.
I'm a technical sales man for used press machine and NC levelling feeder in Korea.
Press machine, feeding machine, milling, lathe, grinding machine, forklift. I handle all press related machines.
If you want to import these machines from South Korea, please contact me.
I hope to have a good relationship with you someday.
Thank you!
From iraq greeting
Greetings from USA
Cho hỏi giá với
Hello
Luar biasa
Thank you.
Hello. Write me contact for this production machine plz
I don't know who made this product and I don't have it somewhere near to me to check it. I purchased it from eBay for a gift to a friend of mine. It was $250 and I consider it as rare opportunity.
Bhai die Banwani ha apna mob. No sand kar da
Veuillez me contacter
مرحبا
As-salamu alaykum.
I can design better
For detail specifications the machine & PRICE Machine PNEUMATIC PUNCH PRESS TESTER
Please Contact
VALTEKINDO
Thank you
Please send me your zig zag servo feeder stainless steel coil circle cutting machine video and details