How to Replace O-Rings in the Group of the La Pavoni Europiccola

Поділитися
Вставка
  • Опубліковано 22 гру 2024

КОМЕНТАРІ • 19

  • @rebeccacheney4732
    @rebeccacheney4732 8 років тому

    Thank you so much for this video. My espresso machine was in desperate need of being serviced, and your instruction made it easy.

  • @paulbignell5697
    @paulbignell5697 10 років тому +2

    Thank you for this video Sir!
    I had stripped and de-scaled my own machine but found that the shower screen and seal kept on coming loose, I hadn't realised but as you pointed out the nut on the piston shaft has to be all the way down. It was driving me nuts. Thank you again :-)

  • @sturbek
    @sturbek Рік тому

    Thank you for your service…

  • @GabrielDiaz
    @GabrielDiaz 10 років тому

    Thanks for this infomation. Would you have some advice regarding cleaning inside of the glass. Thanks for the attention.
    Kind Regards,

  • @dwdp1
    @dwdp1 9 років тому +1

    I'm rebuilding my circa 1982 Pavoni and I also am having problems removing the rusted piston insert pin. I don't have access to a hydraulic press. Any suggestions? I'm soaked it WD40 and also applies citric acid to remove the rust. Thanks!

    • @tmst2199
      @tmst2199 5 років тому

      You might try P Blaster. I think penetrates better than WD-40.

  • @alain8747
    @alain8747 6 років тому

    bonjour Hello
    I have a Europiccola / Professional pavoni with manometer but I do not know if it has an old group or a new.(how to make the difference do you have photos to see the difference ). In addition I do not know where to order the kit to change the joints .
    thank you
    Alain

  • @tmst2199
    @tmst2199 5 років тому

    You da man! It would also be nice to see the details of seal and gasket replacement...

  • @Pierssy
    @Pierssy 6 років тому +7

    Can't believe you skip the two parts where you fit the piston seals and the shower screen seal.

    • @RackwitzG
      @RackwitzG 6 років тому +2

      Yeah, that's a bummer.

    • @tmst2199
      @tmst2199 5 років тому

      Wah. I want more for free!

  • @davidflanagan360
    @davidflanagan360 9 років тому +1

    Hi Ice Dr.
    I have a lever type espresso machine (spring piston type) "Cappucino Amore". I removed the piston and found it has 3 rings with a lip. The top one faces up, second one down faces down. The third one at the bottom of the piston I had removed and don't know remember whether it should be facing up or down. Also, the piston fits inside a 3 in long 1.5 in diameter spring. My questions:
    1. In what order should the sea rings be facing (previous owner told me he had them replaced once but not sure he did it right either).
    2. How to I get the piston to slide up so I can attach the lever with the two pins? Do I need some sort of press? if so what kind ?
    Thanks

  • @brozbro
    @brozbro 6 років тому +12

    How to Replace an Engine in a Ferrari:
    1. Remove the old engine
    2. Install the new engine

  • @chilenito3242
    @chilenito3242 10 років тому

    I would like to be good like you. Where / how can I learn this Ice?. Thanks.

  • @anselmud
    @anselmud 7 років тому +2

    You skip the part I neeeded to understand how to do, the piston removal.

    • @slippyg
      @slippyg 6 років тому

      Rubber mallet my friend

    • @katielerchen3016
      @katielerchen3016 6 років тому

      anselmo talotta, delicately use a rubber mallet