Check to make sure you have bled the fuel to hp pump, crack union nut and make sure there is an atomized spray from hp pump. Check governor is set correctly. Check mag pick up at fly wheel is installed correctly and not faulty Check avr terminals are all secure Check voltage pot on avr is set correctly.
Alhamdolillah my genset same fault solved the main reason of changing of new fuel filter which was little bit wromg and therefore same fault was occurred,, You want to check the final fuel inlet line on FI pum for smooth flow of fuel in the pump
I encountered such problem like that..you need to check your fuel priming pump or another option is you need to supply your generator in a overhead fuel tank so that you will know if you have the problem in your fuel lines or fuel pump system.
Perkins 400D 22T. Multiple units experiencing a 'speed signal lost issue' and one 'over speed issue. New mag pickup did not cure the issue. Less than 1000 hours on the units.
My generator tests weekly without any issues-transfers and engine starts. However, when there is an actual outage, the transfer does transfer, but the engine will not start. I have to manually start the engine, and it does without any issues. Not the battery or fuel because the generator starts manually and quickly. However, I have gone through the troubleshooting steps. Ideas?
Hi good day I have a question I have a Perkins 80kw P883 after sitting for three days, it keep on losing prime I would have to bleed the lines to get it to start up
hi, good information, I have A generator that when it is in running mode it switches back to cool down mode, what is causing that problem, I never seen that happen before
I guarantee you will have wire problems all the time. The whole genset is good except wiring : disaster. Especially important : keep the wires dry, out of water. If you have to wash, isolate all connections previously. Even with this percussion big chance that you'll have problems with starting and running until they dry up completely
hi, the problem of my generator is when start the generator the rpm is normal 18001 and the hz is 60.0 but if i put load the generator rpm will go down 17998 and also the hz go down 50.8 until the generator going to shutdown automatically,can you help me pls.. my generator is catterpillar 700kva
Your problem is diesel problem check the diesel flow from the tank and check the diesel that return to the tank if the diesel stay in the diesel pump the pressure will shut down the generator
Please my generator stops and shutdown when it reaches 12 kilo wat (it is 50 kilo wat normally) Because some programmed that how can I format that programmed
@@abdallaabdi5493 you have to check the fuel pump injector and also the injector nozzle to see if all is well due to the increase in loaf this can effect the speed at which the fuel is coming out if it is not relative to the load it will definitely shut down
Check to make sure you have bled the fuel to hp pump, crack union nut and make sure there is an atomized spray from hp pump.
Check governor is set correctly.
Check mag pick up at fly wheel is installed correctly and not faulty
Check avr terminals are all secure
Check voltage pot on avr is set correctly.
Alhamdolillah my genset same fault solved the main reason of changing of new fuel filter which was little bit wromg and therefore same fault was occurred,,
You want to check the final fuel inlet line on FI pum for smooth flow of fuel in the pump
I encountered such problem like that..you need to check your fuel priming pump or another option is you need to supply your generator in a overhead fuel tank so that you will know if you have the problem in your fuel lines or fuel pump system.
Sir am having problem with wan FG Wilson Perkins, 250kva,,,,,
It ran for about 10 seconds and shut down
@@franciskomba3600 how you fix my friend?
Perkins 400D 22T. Multiple units experiencing a 'speed signal lost issue' and one 'over speed issue. New mag pickup did not cure the issue. Less than 1000 hours on the units.
My generator tests weekly without any issues-transfers and engine starts. However, when there is an actual outage, the transfer does transfer, but the engine will not start. I have to manually start the engine, and it does without any issues. Not the battery or fuel because the generator starts manually and quickly. However, I have gone through the troubleshooting steps. Ideas?
Just noticed the set has ran 32 hours.
So either fuel problem, check restrictions in pipes and check fuel tank level or the governor is possibly loose
If it is only running by around 4 hrs only? Is it still the fuel problem or the gobernor problem
Check the injector pump the rotor head needs to be changed
I am experiencing the same as we speak, if not d fuel line, then it will be the artuator/avr
Hi good day I have a question I have a Perkins 80kw P883 after sitting for three days, it keep on losing prime I would have to bleed the lines to get it to start up
check fuel water sep and Fip & governor setting other wise check AvR
There is Air leaks in the fuel lines or fuel filter is clogged.
hi dear i have the same problem with perkins it is the fuel pump failure you have to rebuild the fuel pump or changed if there is warranty
sounds showing that fuel supply problem,,
either problem in fuel line or fuel pump or filters.
Thank you, it's working
hi, good information, I have A generator that when it is in running mode it switches back to cool down mode, what is causing that problem, I never seen that happen before
i have similar genset,engine crank but can not start, do you have the wiring diagram?
how to check fuel consumption of the same Generator for 1 hour how much it consumed diesel in one hour
Is the coolent supply valve open?....kindly check if the water flow valve is opened or not? Or may be fuel pump problem
100 kVA Perkins Genset. Is either fuel pump is locked up or fuel line is damage or block
it comes up with Gss knock fault present. perkins 750kwa Gas gen. Thanks
How about air damper problem how to solve please
Le mien ne démarre pas, l'electrovanne n'est pas alimentée
Hi ,engine crank Ok and there is fuel in the system with pressure but cannot start, Perkins genset
check injectors
My Perkins 2200 series trip of show me fil sd oil pressure and sd stop fail in Alarm list what is the course?
I had a same problem with my Perkins sir maybe you know about the solutions ?
Can anyone help. 80kva jet generator starting problem.
Hi, Dear.can someone tell me where to find the weight of Perkins Generators?Many thanks
The same 810kw generator trip over speed whats the problem
Hi my generator kicked in but did not hold, I have cleaned the pistons and it is still not holding. Please advice
What could be the reason
Sir,, perkins generator 400kva no start in electrical problem... how to check this problem please.....
O gerador não está a dar arranque tem um ponto de exclamação ❗ que não está a pagar o que posso fazer.
How I check generator fuel letars
Sir 40 kva gen set over speed warning light on and than shout down
Hello sir asalamwaalaikoom where are you located in job. I am now uae this is my whatapp n 00971543895170
help me my generator start and run for while and stop, so what could be the problem?
How can the problem be solved?
Hi friend check the injectors
Mi generador no arranca en el modo automatico
Did you check the generator Frequency? looks like a 50hz setting iddle @1500 rpm
Hector Aponte how to fic fuel sensor fault
@@ramirbasilio7252 You either have to check it or replace if need
ce moteur démarre à une haute température qu'est qui peut cause ça
Change fuel filter, then check again
May be Actuator problem
Can anybody help me, I have a Perkins 50kva shutting down for low voltage. What should I do
Wear u from??? Can I help u
@@perkinsgenerators8372 if you fix generators could you share your number with me
@@omarahmed6175 u welcome sir
I m working in Riyadh KSA
+966551888210
Call+wahtsup
Replace with a new battery but before check the old one if it still working
Program kaise DB me dalte h
i found the problem it was a lose wire on the back of the panel when i open gen up
I guarantee you will have wire problems all the time. The whole genset is good except wiring : disaster. Especially important : keep the wires dry, out of water. If you have to wash, isolate all connections previously. Even with this percussion big chance that you'll have problems with starting and running until they dry up completely
Hello sir my genetior problem is display not conted
Rizwan Haider 00966599369100 py msg kro mujy wathsapp py
Were you able to fix it?
I have also this problem
How to control
hi, the problem of my generator is when start the generator the rpm is normal 18001 and the hz is 60.0 but if i put load the generator rpm will go down 17998 and also the hz go down 50.8 until the generator going to shutdown automatically,can you help me pls.. my generator is catterpillar 700kva
There's a problem on your AVR. Without load the rpm and voltage ok but if theres a load the rpm will go down.AVR problem...
Silahkan check Electrical system (AVR) setting.
Check fuel system
Sir my genrter problem is underspeed
Sounds like a fueling issue
Fuel filter
Your problem is diesel problem check the diesel flow from the tank and check the diesel that return to the tank if the diesel stay in the diesel pump the pressure will shut down the generator
Please my generator stops and shutdown when it reaches 12 kilo wat (it is 50 kilo wat normally)
Because some programmed that how can I format that programmed
H
@@abdallaabdi5493 you have to check the fuel pump injector and also the injector nozzle to see if all is well due to the increase in loaf this can effect the speed at which the fuel is coming out if it is not relative to the load it will definitely shut down
ellow sir .my generator is not working display monitor under speed,,pls help.
Dannyboy Mazo it’s the injector pump the rotor head needs to be changed
Feul pump have adjust rpm
Speed Governors problems
ممكن سؤال
sar,red paiz m.r.p.
O meu gerador no painel sensação pressão óleo