How to make a cheap Cable Finder - DIY Tutorial
Вставка
- Опубліковано 14 жов 2024
- This is a DIY tutorial of how to make a cheap cable finder, that you can easily locate cables and check also the continuity of the wires!
Poseidwn Tech on Social Media:
www.poseidwn.tech
/ poseidwn_tech
/ poseidwn.tech
/ poseidwn.tech
/ poseidwntech
Components :
9 Volt Battery Box : amzn.to/2IItpdR
Set of alligator clips : amzn.to/2G1J0Dj
Buzzer 6-9 Volts : amzn.to/2GgIcxU
9 Volts Battery : amzn.to/2GgJ71k
Cable ties : amzn.to/2GTrAu4
Heat Shrinks : amzn.to/2GfGb51
UHU Mini Super Glue : amzn.to/2GQFi0r
Bic Lighters : amzn.to/2G1XMtU
Tools :
Facom Cable Stripper : sg.rs-online.c...
Knipex Electronics Super Knips Comfort Grip : amzn.to/2EO76Fg
Knipex Cable Stripper : amzn.to/2G1V5IK
Knipex RJ45 Termination Tool : amzn.to/2HuutAC
Dremel Rotary tool : amzn.to/2ub25BF
Connections :
1) Connect the black cable of the buzzer with the black cable of the battery box
2) Connect the red cable of the battery box with the red cable of the alligator clip
3) Connect the red cable of the buzzer with the black cable of the alligator clip
Music :
Morning Sun by Nicolai Heidlas Music / nicolai-heidlas
Creative Commons - Attribution 3.0 Unported- CC BY 3.0
creativecommons....
Music promoted by Audio Library • Video
I have built a few of these over the years and found that adding a red LED into the ckt allows you to see the light in noisy areas and if you use the light only it does not disturb workers in an office environment. You can add an on/off/on three position switch for switching between the light or tone. The video is very well explained. Good job.
This is a continuity tester not a cable finder .
I agree with you! I used this title because i am using it to find cables.
Continuity tester is what I would call your gadget a signal generator and receiver is a true cable tracer
It's not a very good one. You don't want to pump 12V on any voltage sensitive equipment. A better design would use a transistor or FET for turning on the speaker a capacitive sensor.
Very good! I am very curious how you can use this to find cables that are already terminated in patch panel!
Don't worry, you will learn soon!
Serious?
You wand the port on the panel... Duh
I think you meant a cable that's patched into a switch already????
Great trick for a cheap cable finder. Thanks!
Thank you very much for your feedback!
This is perfect for alarm technicians looking for open circuits. Thank you
You are welcome!
When I search for a shorted 12 volt circuit to ground on semi-trailers , I place a 12 volt buzzer inline . A live 12 volt line to one side of the buzzer and the other buzzer wire to the shorted circuited wire . The sounding buzzer will stop after tugging , pulling. , or unwrapping the harnesses , then repair . If the annoying buzzer is too loud place electrical tape over the buzzer sound vent . 6/7/23
Instead of a buzzer a 12 volt an incandescent lamp may be used , this lamp will put more of a current draw on the circuit than an LED lamp . Use alligator clips on these fixtures . A small amount of tape quiets the buzzer significantly .
U use 9 volt battery or 4.5 volt ??
I used for the tutorial a 6 to 9Volts Buzzer so i used a 9Volts Battery.
Verry useful...thanks...
You're welcome! Thank you for your comment!
The knipex tools are nice
Yes i like them a lot.
I like your Dremel. Is this Stylus?
Yes! I forgot to add it in the description.
Does it matter where to connect the red and black alligator clip?
No doesn't matter!
Is this only good for finding short circuits?
I am using it as a cable finder due to it's small size and cost but only for low voltage cables.
This seems the same as using your multimeter!!!
The most reliable way to detect a short circuit.
It is reliable and cheap!
Nothing compares to a professional wire tester.
I agree. But also the price is not compared!
Where do you get a buzzer box?
On Amazon search for 6-9 Volts Buzzer!
How would you use this in coaxial cable setuup
I have used it sometimes with coaxial cable. I connected the cable finder to coper wire and foil shield of the coaxial cable.
Thanks! Looks easy. I will try it!
It is easy! Try it and you will have it always in your tools!
Or buy a multimeter...
You are right with the multimeter you can do the same. The only problem with the multimeter is that the “beeb” is not loud enough. On the other hand this cable finder has a buzzer and it ‘s easy to hear it in a noisy environment. Also it is small and cheap!
It's not a cable finder. It's continuity tester.
Yes and i am using it in order to find cables...
Love it!
Thank you!
I would have soldered wires takes a second lasts forever
That is so true! Thanks for your comment!
This video just only cable tester not Traser
I am using it many years in order to locate cables. It's small, inexpensive and has always a place in my tools!
Excellent! 🙏
Thank you!
How to used 50 meter testing this please tell me bro ?
What do you mean?
This is not a cable finder. It is nothing more than a continuity tester
It is indeed, but i am using it everyday in my projects in oder to locate cables. It is small and inexpensive. Thank you for your comment!
The most VFM tool.
I agree!
The video spends too much time in what is obvious.
In general i am trying to create step by step tutorials that anyone can follow. You are right though that sometimes maybe it's too much...
Ωραίος φίλε...
Σε ευχαριστώ!
Thats not a cable finder. Thats a cheap ass homegrown continuity tester. Something built in to even the cheapest multimeter. Stop wasting everone's time.