Could you please explain which parameter need to change for speed reference selection (Parmeter 22) for this FPBA-01 card control, I think I am missing something because I could start the drive from PLC (rotation sign on drive is on) but speed reference is not going to drive. Drive is sending few voltage when starts but speed ref zero( top right Hz is zero). I am using PPO5 for this.
Sir, It was very informative and good explained by you. I request you please make one video with Siemens PLC and ABB Drive with ABB Drive library. once again thankyou very much for video...
Thank you so much for expounding about the workings of status words and control words of a GSD. I just noticed that there were 2 rows under the ABB module PPO, the 4AX and the 6AX. You only use the IO address under 6AX row. What is the purpose of the 4AX row. Also, in some 3rd party device configuration there's a column that's called diagnostic address. Maybe you can explain to us on what is diagnostic address is for.
The 6AX are the PZDs which i have used in the program for data transfer betw plc and drive. As u can see there are 6 inputs available for reading 6 values from the drive. So if you need to read more values you can use 4AX , which are the PKW, and this can be used to directly read from the drive parameter without any parameter configuration required.Using PKW for reading the values from the drive is a bit tricky though. You need to the write the HEX code of parameter group in first PKW output and Hex code of parameter number in second PKW output. The value of the parameter can be read in fourth PKW input. Confused?
@@averageengineer4266 I got it! I hope you will also make a video for integration of Lenze Servo Drives 9400 HighLine with S7 controllers using PZD PPO. Lenze 9400 does not have a lot of information that can be found in YT. A lot of industries in the U.S. are using this drive. Thank you and hope you will continue sharing your knowledge.
Please help me, in speed refference couldnot be responded if I give value from progam, I'm very gratefull if u can give me a phone number for asking my problem Mr.
Could you please explain which parameter need to change for speed reference selection (Parmeter 22) for this FPBA-01 card control, I think I am missing something because I could start the drive from PLC (rotation sign on drive is on) but speed reference is not going to drive. Drive is sending few voltage when starts but speed ref zero( top right Hz is zero). I am using PPO5 for this.
please. I have a same problem
Sir,
It was very informative and good explained by you.
I request you please make one video with Siemens PLC and ABB Drive with ABB Drive library.
once again thankyou very much for video...
Never used it, but i will try, thank u..
@Average Engineer,is it possible to upgrade modus to profibus on abb drives?
Yes, you will require a profibus adapter on the drive
@@averageengineer4266 thanks
Thank you so much for expounding about the workings of status words and control words of a GSD. I just noticed that there were 2 rows under the ABB module PPO, the 4AX and the 6AX. You only use the IO address under 6AX row. What is the purpose of the 4AX row. Also, in some 3rd party device configuration there's a column that's called diagnostic address. Maybe you can explain to us on what is diagnostic address is for.
The 6AX are the PZDs which i have used in the program for data transfer betw plc and drive. As u can see there are 6 inputs available for reading 6 values from the drive. So if you need to read more values you can use 4AX , which are the PKW, and this can be used to directly read from the drive parameter without any parameter configuration required.Using PKW for reading the values from the drive is a bit tricky though. You need to the write the HEX code of parameter group in first PKW output and Hex code of parameter number in second PKW output. The value of the parameter can be read in fourth PKW input. Confused?
@@averageengineer4266 I got it! I hope you will also make a video for integration of Lenze Servo Drives 9400 HighLine with S7 controllers using PZD PPO. Lenze 9400 does not have a lot of information that can be found in YT. A lot of industries in the U.S. are using this drive. Thank you and hope you will continue sharing your knowledge.
Good and easy explanation. Thanks
How operate the fieldweakning parameter of DCS800
Emf tuning must be done to have field weakening
Thanks
sir i cant dounload abb drive "ACS560-01-062A-4 + ACS-AP-S" gsd
Perfect tutorial~ Btw, could you show the SFC14 for the ACS880 communication
I will definitely try out, thx for watching
Nice vedio.... can you make one vedio on delta ss2 series plc with yaskawa v1000 drive
Thanks for your video
Thanks for video
Nicely explained
Very nice video
Amazing ❤️
Thanks for watching
Great
Please help me, in speed refference couldnot be responded if I give value from progam, I'm very gratefull if u can give me a phone number for asking my problem Mr.