Самоделки хают те, кто не хочет заморачиваться. А вы сэкономили, молодец. Я тоже делаю для себя самоделки, на некоторых даже зарабатываю. Тебе за труд респект.
В 1977 году учился в техническом училище . До сих пор помню одно из правил работы на токарных станках . При длине заготовки более семи диаметров применять поддержку задним центром . Длиннющая скалка при почти 3000 оборотов в минуту в мгновение согнет вал если не будет ограждения . Получится нунчак как у японских ниндзя на скачущем по мастерской основании. Написал не для мастера а для тех кто задумает повторить данный агрегат. Для безопасной и надёжной работы надо закрепить торчащий вверх конец вала.
You can tell he’s had that motor apart before, maybe more than once it looks like. It came apart way to easy. Any .I’ve disassembled has been much harder to separate than that, even with a hammer.
Хорошо, что шпилька была не двух метровая а то бы размаха рук бы не хватило кружки стянуть.))) да и шпильки одной бы хватило, просто барабаны со шкурой менять, а то неудобно ключом в такую щель лазить. Сверху удобнее крутить.!!
The idea of the thing is ok, but it ended there as you can see when the project was concluded. It truly is a diy project. It’s nor squared, even close and the moving parts is going to ruin a lot of thing he tries to do with it. Question for you, WHY DO YOU THINK HE CHOSE THE FILLER HE DID. He chose the roller that was the second largest roller, can you imagine how over sized the hole ' would have looked if he had used the second largest filler which was the one he cut for it. I started my upholstery shop in 1963 and one thing I’ve learned over the years is measurements must be precise or you may screw up a piece of furniture real easy and a lot of the time you, as I said, screw up something that might have started out to be expensive but now has to be sold as damaged or seconds or thirds, depending how bad it looks or fits. He is going to ruin a lot of fits with those drum sanders, did you see how wobbly they were moving up and down, it’s going to be hard to sand anything precise with what he made here. There are other faults, with it to, bad ones. For it to be a good project will require a lot of changes actually. If you are going to build it may I suggest that you take the plans or the video and let someone you trust go over it with you.
I had to close my eyes when drilling steel flat bar by hand you’re not going to cut your hands open!! Put steel in a vice 😢 plus use bench drill as hand drill can fly out your hands hurting you!!
Самоделки хают те, кто не хочет заморачиваться. А вы сэкономили, молодец. Я тоже делаю для себя самоделки, на некоторых даже зарабатываю. Тебе за труд респект.
В 1977 году учился в техническом училище . До сих пор помню одно из правил работы на токарных станках . При длине заготовки более семи диаметров применять поддержку задним центром . Длиннющая скалка при почти 3000 оборотов в минуту в мгновение согнет вал если не будет ограждения . Получится нунчак как у японских ниндзя на скачущем по мастерской основании. Написал не для мастера а для тех кто задумает повторить данный агрегат. Для безопасной и надёжной работы надо закрепить торчащий вверх конец вала.
А нафига...!!??😂😂😂
Thanks for your additional tip.I appreciate you.Im learning more and more everyday
Never used a vice like you have. 🎨Art work 💪🏾
Fino maestro,elegante. Saludos desde cucuta Colombia.
Toda esa manufactura artesanal EXCELENTE.
عمل رائع جدا 🎉
Yo tendria gue cer un industrial con todas las máquinas para hacer esta máquina Luis quiroga
O vo je dokaz kad majstori nemaju novaca pa sd bore sa svojom idejom od koje nece i.ati puno koristi
Vídeo muito cumprido . Se já enrolou uma peça igual, pra que fazer com a outra ! Cansativo !
Very Good Job 👏👏👏👏👏👏 Excellent
😮😮 bạn đúng thật là có một tối tạo tuyệt vời 😅
good
Se me va la vida viendo esto!! No lo podés hacer más corto?
👌🏻👍🏻👏🏾👏🏾👏🏾👏🏾👏🏾👏🏾👏🏾🤣😂👏👏👏👏👏👍🏻👍🏻👍🏻
Parabéns pelo belíssimo profissional que você é.
You can tell he’s had that motor apart before, maybe more than once it looks like. It came apart way to easy. Any .I’ve disassembled has been much harder to separate than that, even with a hammer.
Eu tenho um motor desse mas não sei ligar os fios o amigo pode me ensinar como ligar do jeito certo
Muito trabalho, vou comprar um torno 😂😂
At 34:34, sounds like a 'wild pig' in heat.... carry on, good video so far... G
Too much work for something so useless. At least it was content to make this vid.
Инструменты хорошие токарный понравился а мамоделка фуфло.
Wiring plan of electric motir please... capacitor value etc...plans of wiring in general
If you have to ask such tame questions dont try to build anything
Just confirming the point mentioned
Te safety.
I don’t believe you’ve been on this 11 years and don’t have any subscribers.
Muito bom
Coś ci ta maszyna za bardzo podskakuje. Nie wiem czy ta obróbka będzie dokładna
Хорошо, что шпилька была не двух метровая а то бы размаха рук бы не хватило кружки стянуть.))) да и шпильки одной бы хватило, просто барабаны со шкурой менять, а то неудобно ключом в такую щель лазить. Сверху удобнее крутить.!!
The idea of the thing is ok, but it ended there as you can see when the project was concluded. It truly is a diy project. It’s nor squared, even close and the moving parts is going to ruin a lot of thing he tries to do with it. Question for you, WHY DO YOU THINK HE CHOSE THE FILLER HE DID. He chose the roller that was the second largest roller, can you imagine how over sized the hole ' would have looked if he had used the second largest filler which was the one he cut for it. I started my upholstery shop in 1963 and one thing I’ve learned over the years is measurements must be precise or you may screw up a piece of furniture real easy and a lot of the time you, as I said, screw up something that might have started out to be expensive but now has to be sold as damaged or seconds or thirds, depending how bad it looks or fits. He is going to ruin a lot of fits with those drum sanders, did you see how wobbly they were moving up and down, it’s going to be hard to sand anything precise with what he made here. There are other faults, with it to, bad ones. For it to be a good project will require a lot of changes actually. If you are going to build it may I suggest that you take the plans or the video and let someone you trust go over it with you.
This guy never heard of Harbor Freight???
I had to close my eyes when drilling steel flat bar by hand you’re not going to cut your hands open!! Put steel in a vice 😢 plus use bench drill as hand drill can fly out your hands hurting you!!
-33.17 ??
What are. You going To do I don't have any idea
Oi BOA TARDE TUDO BEM EO GOSTARIA DE SABER QUER MOTOR E ESSE POR GENTILEZA
Não acredito que você fez tudo isso pr
А сейчас стало модно немое видео снимать?
Another heath Robinson concoction.
o my goodness
Стержен очень слабая
Придумай что-нибудь надйожный.
Where is the music?
Мастер
Сколько ты испортил материала впустую 😂
je trouve le résultat final plus que moyen
¿Tiene malas manos? envidia que tienes."E pur se mueve"(y lo quemaron)
خيلی طول میدهید
If you showed the =>>electric WIRING process ADD the Plan though. Thanks! √
Сколько ты испортил материала впустую
Has obviously never been trained in basic engineering skills and safety.
What type of glue and spray are you using.?
I would think the same.
Its oil
😮@@bahnxapsw15676gr1😢
2²22
❤❤s
Не нужная поделка!!!😂😂😂
samo nakladanje
West time .
Ваня, тибе кто на английском писал.
А тИбе кто на русском?
МУДОЗВОН!!! Верни время! Займись пением и будет вторая Бузова
Долго делаешь, ток время тратить
😂😂😂😂😂😂
Not good
This is so useless AF with that much work. That AC cord use to be white, it is so old it will blow up soon.
Мозгодолбвтель
your inutile invention,is wast of time
A useless thing, Badly made from a lack of coherant thinking.