@@DineshChandra Please clear 1 doubt, as per calculation, it comes 0.6mm diameter need to used for 1.41A current, but 0.6mm wire can handle maximum 1 Amps, how to cope with this?
Sir video bahut acchi lagi Majid isko aasan Karen hamare Liye Taki Ham aasani se motor winding kar sake formula nikal sake kyunki hamari itni talim Nahin hai thank u
Accually I have been suffering a problem for few days to wind a 3 phase 3 hp 2 pole 36 slots water pump motor which has wind two times already by other person with swg 23 with 56 turns per slot in full pitch distributed in star connection but It is burned out in load again and again .I was given to solve that problem again from my boss.
@@DineshChandra Here if we calculated pitch factor. Kp=sin(150/2)=0.9659. Then Distributed factor Kd=sin(2*30/2)/2*sin(30/2)=0.9659 So product of this two factor comes=0.933... Am I wrong or right? If I wrong,would you please tell me the correct value of pitch factor and distributed factor?
@@numerical9537 in this video I was considered approximate value for general calculation but theoretically you are right, procedure will be same as you say
Sir in big motor like 10KW to 50 KW there are operates in Y or ∆ . If this motor run in star is takes less of current instead of delta. In this situation consume different amount of current , in this case the motor have same types of SWG in its winding?? Please answer sir
This situation is not permanent because in starting we need more torque to start the motor and after achive 75 percent Speed of motor we connect it in delta. SWG will calculated under Full load or running condition.
Sir, CRI monoset pump hai 3 phase, 3 HP, 24 slot, RPM 2880, effi. 53, voltage 350, L-8.5 cm, D-8.5 cm, connection - Delta, ye motor ka Data nahi hai to find out Turns, SWG galat ho gaya pz nikalke do, I request.... I working this motor, video send pz...
Sir , please tell me,how to use these calculations for a single phase motors. Do the three phases work independently or these have some sharing of flux with each other?
Flux density depends upon magnetic material so it can be veries between 0.4 T to 0.55 T as I say in my previous video , I assume a constant value between these 2.
Sir it's Request please help it's my Question 150w 3phase D-4.8 L=6.8 stot-24 RPM2800 Sir iska turn ,pitch ,wire Gauge?? PlS ANSWER ME PLS IT'S A RQST PLS Pls answer m
hello sir and thank you so much if we have induction motor whitout name plate how how determines specific electrical loading according to length and internal diameter the motor for calculation power this motor and the value specific electrical loading is increase if the power is big or opposite genially
Thanks for prompt reply. The motor is sigle phase, 1.5Hp, core leght 6cm, core diameter 7cm, and 24 slots. Can you calculate for 4 poles, the numbers of turns and the thikness of the wire? FOR SIGLE PHASE MOTOR, and design the wirimg? Thank you very mutch. I m waiting...
Power in terms of Phase voltage and Phase current will be ( 3×Vph ×Iph × cos phi ) but if you take in terms of line power will be (√3 × VL ×IL × cos phi)
May I get ur mail id/msngr id/fb id to verify my calculation and solve this pblm or suggest me here?I calculated all the parametters and equations but number of turns in slot and cross section area of swg didn't match with before.I also checked with other mathod but there is same problem.
![All Motor Winding Formula Calculation With Stator[Washing Machine Motor Winding]](http://i.ytimg.com/vi/gi8nrrHiYw4/mqdefault.jpg)
So versatile knowledge impartation
very nice brother
Thank you sir
@@DineshChandra Please clear 1 doubt, as per calculation, it comes 0.6mm diameter need to used for 1.41A current, but 0.6mm wire can handle maximum 1 Amps, how to cope with this?
Sir video bahut acchi lagi Majid isko aasan Karen hamare Liye Taki Ham aasani se motor winding kar sake formula nikal sake kyunki hamari itni talim Nahin hai thank u
Video bahut acchi hai thoda sa Majid isko aasan Karen Taki aam electrician isko istemal kar sake thank u
Very nice sir
Thanks for the prompt reply.
Accually I have been suffering a problem for few days to wind a 3 phase 3 hp 2 pole 36 slots water pump motor which has wind two times already by other person with swg 23 with 56 turns per slot in full pitch distributed in star connection but It is burned out in load again and again .I was given to solve that problem again from my boss.
I followed the book electro motor which has been written by Neven sbr.which book did you follow?Inform me please.
15.7÷(od ×id(inch)×3.14 pai
Sir,
I'm from Bangladesh. Please give me name of book for motor rewinding issue.
Sir why do you use Kw=0.954 always. Isn't it the product of pitch factor and distribution factor?
Right, and kw always less than 1 because of winding are distributed in machine
@@DineshChandra Here if we calculated pitch factor. Kp=sin(150/2)=0.9659. Then Distributed factor Kd=sin(2*30/2)/2*sin(30/2)=0.9659
So product of this two factor comes=0.933... Am I wrong or right? If I wrong,would you please tell me the correct value of pitch factor and
distributed factor?
@@numerical9537 in this video I was considered approximate value for general calculation but theoretically you are right, procedure will be same as you say
Sir in big motor like 10KW to 50 KW there are operates in Y or ∆ . If this motor run in star is takes less of current instead of delta.
In this situation consume different amount of current , in this case the motor have same types of SWG in its winding??
Please answer sir
This situation is not permanent because in starting we need more torque to start the motor and after achive 75 percent Speed of motor we connect it in delta.
SWG will calculated under Full load or running condition.
सर कृपया मुझे ये बताइये की कुलर किट मोटर का वाइंडिंग डाटा केलकुलेशन आप ने किस पार्ट में बताया है
Single phase motor winding
G bhai jan 1recoest ha ap ko thori si zehmet de raha houn...plz plz zara totel ourdo mein bata dein apki mehrbani ho gi.... shahbaz sagher
Sir .
Table fan 16 slot wali motor ka winding formula per 1 video bane
Sir, CRI monoset pump hai 3 phase, 3 HP, 24 slot, RPM 2880, effi. 53, voltage 350, L-8.5 cm, D-8.5 cm, connection - Delta, ye motor ka Data nahi hai to find out Turns, SWG galat ho gaya pz nikalke do, I request.... I working this motor, video send pz...
Sir , please tell me,how to use these calculations for a single phase motors. Do the three phases work independently or these have some sharing of flux with each other?
sir ek motor hai jo 3 phase mai hai uska plat mai likha hai 2880rpm 415voltej 1.1 amp. frame size 63 hai iska winding data hal kijiye
Sir single phase motor data Ka formula bataiye
Aap playlist me dekh sakte ho aur aaj ke video k description box me link mil jayegi
Sir singel phase ki video banaye
💕💞❤ thank sir
Most welcome dear
Sir next time can you make a same vedio taken by a 10KW motor or 15 kw motor data ??
Sure
Thanks sir
Welcome
Sir, Double layer winding and Single layer winding kon kon se motor me hoti hai pz send video
why did you take (Bab=0.48)this value for determining magnetic flux density?where did you get this value?
Flux density depends upon magnetic material so it can be veries between 0.4 T to 0.55 T as I say in my previous video , I assume a constant value between these 2.
thanks a lot
thanks a lot
Most welcome sir
Sir it's Request please help it's my Question
150w 3phase D-4.8 L=6.8 stot-24 RPM2800 Sir iska turn ,pitch ,wire Gauge?? PlS ANSWER ME PLS IT'S A RQST PLS
Pls answer m
Length ki unit kya hai
150 Watt ye aap ek bar fir check kijiye and diameter and length inches main hai ya koi aur size hai
hello sir and thank you so much if we have induction motor whitout name plate how how determines
specific electrical loading according to length and internal diameter the motor for calculation power this motor and the value specific electrical loading is increase
if the power is big or opposite
genially
Please wait
The swg formula does not working on heavy motors it only working under 7 hp motors
Why you don't make vidio in English language ?
Diameter se SWG kaise nikale sir aapka formula samajh mein nahi aa raha hai example Bata dijiye sir
Area =π×r² R kya hota hai sir pura r² ka matalab sir
Sir please confirm 1000 rpm 1500 rpm and 3000 rpm conductor size same please confirm
Conductor size depend upon rating of machine na ki rpm
Rpm decided by number of poles of machine
5hp motor 1000rpm 1500 rpm and 3000 rpm conductor size same please
Good question i will tell you later👍
Confirm please
sir srator D L size to hp calculation formula?
Please check playlist
Thanks for prompt reply. The motor is sigle phase, 1.5Hp, core leght 6cm, core diameter 7cm, and 24 slots. Can you calculate for 4 poles, the numbers of turns and the thikness of the wire? FOR SIGLE PHASE MOTOR, and design the wirimg? Thank you very mutch. I m waiting...
you have to wait for this ...
Kidly provide video 1,2
Please check playlist for complete part
🙏🙏🙏🙏🙏
Pls do subtitle to English cos of people like me who is interested but don't understand your language
@Taiwo Akin sir thank u so much for your valuable suggestion
Sir cooler motor ka temperature aur watt kaise control karen
Number of turns yadi ek limit se kam honge toh losses badhenge kyoki current jyada flow kregi jiski wajah se winding heat up hogi
@@DineshChandra agar sir number of turns kam karte hain to motor kam powerful ho jayegi
@@DevChauhan-eo7iz bilkul aur Motor current jyada legi load k sath
π ka matalab 3.14 hota hai d² ka matalab kya hota hai sir
Diameter ki power 2
@@DineshChandra 2 ka matalab sir kya hota hai
सर जी आप जो अंतिम मे वायर वाली जो फॉर्मूला समझाया वो मै समझ नहीं पा रहा हूँ कृप्या पुनः समझाय
Jarur bahut jaldi iska ek aur video banaunga 👍
why didn't you take (p=root3 VI cos phi) in terms of (p=3VI cos phi)??
Power in terms of Phase voltage and Phase current will be ( 3×Vph ×Iph × cos phi ) but if you take in terms of line power will be (√3 × VL ×IL × cos phi)
Even I try to explain each and every section but if you have any doubts please ask me anytime I will try to clear it .
thanks a lot
Bhai shab g ac gernoter ka winding data kese niklte hai 1fej or 3fej ka
Jarur generator ke data available hote hi banaunga
मैं आपके साथ काम करना चाहता हूं
Just keep in touch sir
I want to learn work from you. Please call my number
@@nimaidebnath5633 can I get your number please
4.44 Kya hai sir
Aap ye video dekh lo
ua-cam.com/video/pLPKLnuAtBE/v-deo.html
πD²/4 D²=0.359 D=0.6mm sir samajh mein nahin a raha hai
Please
thanks for all
π²=π(D|2)² πD²/4 samajh mein nahi aa raha tha sir example Bata dijiye sir please
3 phesa single lyer winding ,24,slot ,4pole turns
Swg wire ,3 phrase winding ,4 pole ,turns
Bav0.48. Constant taiga. Sir
Where is 0.48 from
Single face motor da number Baroda formula
Swg formula kya hoga ki slot nikal le
Smjha nhi aap kya puchna chahte ho
Hi
Sir mera kuch sabal haa janna catahu app kay number mil jatay to bohat madat hoga please sir help me
Aap kabhi bhi puch sakte ho dear
@@DineshChandra sir sab lik kay nahi bol saktaa app kay contact number miljayega to bohat madat hoga sir mera number haa 8759743745 please sir help
Sir cooler motor ki data kese nikale
Wait kro jaldi lekar aaunga
May I get ur mail id/msngr id/fb id to verify my calculation and solve this pblm or suggest me here?I calculated all the parametters and equations but number of turns in slot and cross section area of swg didn't match with before.I also checked with other mathod but there is same problem.
Wait for all
ok sir
ua-cam.com/video/iXFE3oIhkDo/v-deo.html
Also you can check this video
Sir समझ में नही आया
Upcoming video dekh lena fir kuch nhi smjh aaye to batana
Kuch smj ni aya sari bate hwa maai hai apki
मैं आपके साथ काम करना चाहता हूं