It is guys like you that will push your country forward and I salute you. A word of advise, both WELDING and heating “spring” steel will weaken the metal, that’s what caused your “snap”.
Something I learned to do starting when I would brake springs on my Caterpillar tractor walking beam, is like your blue part / spring steel when finished cutting and bending on it is to heat the entire part good and hot and stick it in isolation over night . This annealing process takes the tension out of the work and it won't break again nearly as easy or often. Good Video Thank you
You should re-heat that entire part, then temper it properly. After bending it and working it, you likely caused the metal to have internal stresses and flaws, possibly small cracks. Something to remember for future? This is, however a very good idea.
That correct, not everyone wants to go buy a toe jack just to do your own projects Especially when U have the ability and knowhow to make your own, "Ingenuity", when that bend snapped off, it just needed annealing, U did that when U welded the piece back on. I guess 7018 ? Good Choice. Great Video.
Такими донкратоми, оригинального исполнения Я пользоволся при монтоже оборудования в 1988г немецкого производства. Идея очени нужная,это есть нулевой подьём.лайк.
This is a great idea . I am retired as master Mechanic / master welder. . It is sad to See this man lighting his oxy- acetaline Torch with no o2: in the torch . The Flame from only acetaline will carbon Up the torch . The proper way to light Is with all fuel and some oxygen . And proper way to stop torch is turn off Acetaline first giving no flame to carbon Up the torch .
Make sure you remove the hydraulic oil from the vessel before welding, if the oil is left in and excessive heat is applied from the welding it could cause the oil inside the cylinder / vessel to explode.
Сначала антилайк хотел поставить: за несоблюдение мер безопасносности, незнание технологии процесса, за сварку к домкрату, за использование рессоры. Но вот за честность-когда лопнула эта красивая рессора-лайк и поставил... Правда потом всё опять пошло не по правильному... Ты там себя береги, брат-америкашка! 😁
Nice to read a positive comment about a worker's ingenuity and hard work. He solved problems and succeeded with the tools and skills he had to work with. I found it interesting, but that's just my opinion. But, I also learned a lot from all the experts' critiques..
You guys are all wrong. The best part was when he gave a “thumbs up” at the very end! He was proud of his accomplishment. I was happy that he didn’t end up in the ER and/or he is still alive!
Do not, ever, put your hand nor anything belonging to your body, under a heavy load. He just didn't realized the same container that went down in front of him can go down again and he put his right hand under that mass chopping bulk of steel. Don't do it again. Or you'll use the left one, until Jehovah regrow your smashed under a 4.8 Ton container right hand just to save few bucks. Don't play with your body pieces. Protect yourself, and keep inventing! Take care! And thank you! Also, whenever you're placing a pad under your container. Use 2 minimum. Bricks whatever you use, use 2 +. If one decides to break, it'll hit the ground or loose level. 2 +, will back up one.
As was mentioned, the jack seals are probably ruined, but on top of that....NEVER put that kind of weight on bricks. I have personally seen them crack, on much less weight. This whole thing was very, very dangerous.
Should have reduced the load on one corner by jacking with two jacks. Then the original would have worked and you wouldn’t have wasted all your time. So you would need two? So what, I’m sure it cost less than all the time, effort, welding materials etc.
Có sáng tạo nhưng cẩu thả trong kỹ thuật rẩy dễ xa nghề. Rất nhiều cẩu thả, trong đó cách cầm viên gạch thứ nhất đưa vào chêm chịu tải, đưa vậy, cup ben đội bể hay thanh sắt câu bị gãy thì bàn tay cầm viên gạch sao nhỉ. Hihi
Well I say well done to him for persevering with it and he must be a good welder after fixing it on the bend like that, you all need to stop saying negative shit and go troll something that actually deserves it
Why am I watching this??? Have no jack, no container, no burner, no welder, no need to lift a 40ft container. Need to watch the vid again, to find out......
@@tubergenmotorsports4193 perfect response. I learned several things from what is being done. Also, learn even more by reading comments. Most are knowledgeable and well intended by experts. I don't agree with calling someone stupid because we disagree with how they do things. To me, ignorance us not necessarily stupidity. He may just lack training and is doing the job as he was taught. Hopefully he can learn to do a better job and be safer before he or someone else gets hurt. I wish him well.
i .worked with a friend at hights that used to tack weld without a helmet always said he shut his eyes in time . he was blind 1 year latter with burns to the back of his eyes DONT DO IT
Try adding stiffeners on the edges and sides. Think like a c section piece of steel bent into your s shape. It will make the piece much stronger and safer and still allow the clearance you need. Be safe friend.
I see that someone also noticed the faulty Procedure that destroyed the jack seals and Left the metal in quenched . Good idea But wrong procedure. Some one please Educate this man .. help him !!
,,,CON UNA GATA DE TIJERETA DE SOLO TRES TONELADAS Y QUE SON BIEN BAJITAS , ,,,, LA PONES POR EL OTRO LADO QUE SE VE QUE TIENE ALTURA Y NO TE HUBIERA COSTADO TANTO ......
Love this. My wife is Korean, and when we take trips to see the family I think I get an ulcer every time. They are the most care free thinkers around. All they tell me is ....Ahh it's ok don't worry.
@@АндрейНазаров-п4й, домкрат должен оставаться таким, как им он был "таким он и остался". Когда тяжёлая единица поднимается, точка опоры перемещается - ещё больше нагрузка на шток, чем сам вес и, если не ошибаюсь, в конце ролика, шток возвращался с трудом.
It is guys like you that will push your country forward and I salute you. A word of advise, both WELDING and heating “spring” steel will weaken the metal, that’s what caused your “snap”.
You are right. It is tricky but it can be tempered to retain much of its strength
Very good bro।
Most of the comments below critique his work...but if you look close....he still has a job....
You did OK buddy...problem solved...innovate, improve, implement...
Têm gente que não gostou mais é nota 10
Nice design and nice work !!
عاشت الأيادي ،، احسنت عملاً يا بطل
탄소강이라서 불 먹으면 쉽게 부러지니까 템퍼링 해야 되죠.
산소로 살짝 달궜다가 천천히 식혀주면 좋습니다.
워낙에 재주가 좋으셔서 뚝딱 만드시네요.
발톱 자키가 가격도 싸고 좋은데요.
LOVE all the commercials! more! please!!!!!!!!!!!!!!!
Canal seu estilo cars deixando aquele like
Muito criativo gostei ..genio
Nice colours
Something I learned to do starting when I would brake springs on my Caterpillar tractor walking beam, is like your blue part / spring steel when finished cutting and bending on it is to heat the entire part good and hot and stick it in isolation over night .
This annealing process takes the tension out of the work and it won't break again nearly as easy or often. Good Video Thank you
You should re-heat that entire part, then temper it properly. After bending it and working it, you likely caused the metal to have internal stresses and flaws, possibly small cracks. Something to remember for future? This is, however a very good idea.
Excellent solution and great tool.
Anyone who has worked construction like I did can see much more uses for this jack than just to lift this metal storage unit great idea
Nicho Sena cum sa demontez electromotoru la citroen sara 1, 9 dizel
Ótima ferramenta parabéns
This is a real guys life that shows ingenuity is still is around and WORKS.
‘And add in hard work.
That correct, not everyone wants to go buy a toe jack just to do your own projects Especially when U have the ability and knowhow to make your own, "Ingenuity", when that bend snapped off, it just needed annealing, U did that when U welded the piece back on. I guess 7018 ? Good Choice.
Great Video.
@@billarroo1 That's the problem he thinks he has the ability and the know how which he doesn't have thats why he nearly got killed!!!
Kreatif banget gaes
Такими донкратоми, оригинального исполнения Я пользоволся при монтоже оборудования в 1988г немецкого производства. Идея очени нужная,это есть нулевой подьём.лайк.
Good like....👍👍
Never gave up! Don't ya just love a project like this... Bravo!
Nice job
This guy is just using what resources are available. No money. Just lots of time. No words about safety.
Este hombre es un cacahuatero profesional
YOU did nice job. 👍👍👍👍👍👍 I realy like it.
Хорошо.но самку можно резко сократить тогда ролики будут интереснее!
достойно..Зачет!
This is a great idea . I am retired as master
Mechanic / master welder. . It is sad to
See this man lighting his oxy- acetaline
Torch with no o2: in the torch . The
Flame from only acetaline will carbon
Up the torch . The proper way to light
Is with all fuel and some oxygen .
And proper way to stop torch is turn off
Acetaline first giving no flame to carbon
Up the torch .
That lift hook certainly needs a proper heat treatment. I wonder, why the bricks didn't crush - always put some wood between bricks and iron.
Like the safety boots
really enjoy that the builder is so persistent on making that tool work great build !..
WOW my friend you are really GOOD...Thanks for share!
Make sure you remove the hydraulic oil from the vessel before welding, if the oil is left in and excessive heat is applied from the welding it could cause the oil inside the cylinder / vessel to explode.
Сначала антилайк хотел поставить: за несоблюдение мер безопасносности, незнание технологии процесса, за сварку к домкрату, за использование рессоры. Но вот за честность-когда лопнула эта красивая рессора-лайк и поставил... Правда потом всё опять пошло не по правильному... Ты там себя береги, брат-америкашка! 😁
Great Job
Be careful, cinder blocks have a tendency to shatter and crumble too. I'd used wood or steel blocks.
You have some of the best blow torching skills ive ever seen. Excellent job on jack. Engineering mind. Great skills
Nice to read a positive comment about a worker's ingenuity and hard work. He solved problems and succeeded with the tools and skills he had to work with. I found it interesting, but that's just my opinion. But, I also learned a lot from all the experts' critiques..
Apparently you haven't been around welders/fabricators that actually know what they're doing.
무릎 나가겠습니다.ㅠㅠ앉아서 작업하시는데...무릎관절 건강 잘 챙기세요
Very good
You guys are all wrong. The best part was when he gave a “thumbs up” at the very end! He was proud of his accomplishment. I was happy that he didn’t end up in the ER and/or he is still alive!
La idea está buena, pero el material debe ser más resistente
In fairness to him he got his job done so he is a winner
Good job nice video .
Do not, ever, put your hand nor anything belonging to your body, under a heavy load. He just didn't realized the same container that went down in front of him can go down again and he put his right hand under that mass chopping bulk of steel.
Don't do it again. Or you'll use the left one, until Jehovah regrow your smashed under a 4.8 Ton container right hand just to save few bucks. Don't play with your body pieces. Protect yourself, and keep inventing!
Take care! And thank you!
Also, whenever you're placing a pad under your container. Use 2 minimum. Bricks whatever you use, use 2 +. If one decides to break, it'll hit the ground or loose level. 2 +, will back up one.
Buen trabajo
great idea! i have never seen stick welding done like that before. GOOD LUCK
Megusto la persistencias bendiciones
Muito bom sua ideia valeu irmão
ñ Mm mm:
FINALLY! Someone who uses a cutting torch. Thumbs-up!!
Almost the right idea. Needs the base plate to be twice as big atleast and go well under the container. The load is almost on the edge of the base.
Super
기성품 지레작키쓰시는게 안전할듯 하네요.
As was mentioned, the jack seals are probably ruined, but on top of that....NEVER put that kind of weight on bricks. I have personally seen them crack, on much less weight. This whole thing was very, very dangerous.
그리고, 아시겠지만 지렛대도 그런식으로 굴곡을 준 좀 더 긴 걸로 하시면
더 좋을 듯 합니다.
Should have reduced the load on one corner by jacking with two jacks. Then the original would have worked and you wouldn’t have wasted all your time. So you would need two? So what, I’m sure it cost less than all the time, effort, welding materials etc.
Skilled metal working and impressive results! Champion of a low cost build
Seals in that Jack are done. Finished.
Có sáng tạo nhưng cẩu thả trong kỹ thuật rẩy dễ xa nghề. Rất nhiều cẩu thả, trong đó cách cầm viên gạch thứ nhất đưa vào chêm chịu tải, đưa vậy, cup ben đội bể hay thanh sắt câu bị gãy thì bàn tay cầm viên gạch sao nhỉ. Hihi
Interesante....saludos desde Venezuela
I could hardly contain myself
Why not just use a floor jack and position it in the opening near the leg, that should work.
Great video. I love how you showed the progression as you improved your jack setup. Thanks.
Ooh safety....ya man... just like in China... just thinking about welding an oil-filled cylinder
Well I say well done to him for persevering with it and he must be a good welder after fixing it on the bend like that, you all need to stop saying negative shit and go troll something that actually deserves it
Those jacks have been around for 70 yrs or more, designed by Tangye of England , Would lift a damn site more than a Poxy 4 ton container may I add.
I appreciate his effort and ingenuity but thus is as exciting as watching grass grow.
Floor jack like you use in a shop would be much easier to use.
Why am I watching this??? Have no jack, no container, no burner, no welder, no need to lift a 40ft container. Need to watch the vid again, to find out......
That's funny! Welcome to the Internet. I like to try to pickup bits and pieces of knowledge of whatever people are making or doing.
@@tubergenmotorsports4193 perfect response. I learned several things from what is being done. Also, learn even more by reading comments. Most are knowledgeable and well intended by experts. I don't agree with calling someone stupid because we disagree with how they do things. To me, ignorance us not necessarily stupidity. He may just lack training and is doing the job as he was taught. Hopefully he can learn to do a better job and be safer before he or someone else gets hurt. I wish him well.
Bien dicen que mas vale maña que fuerza, aquí fue maña y poca inversión!!!!!!. Saludos
Arc welding directly onto a hydraulic cylinder .... OMG
MUCHO POR ESO CAMARADA. FELICIDADES.✔✔✔✔✔✔✔
CAUTION, PRECAUCION ,WARNING
Handy for everyone who needs to lift a container this way....we use forklift....
Que capo!! Pero porque se rompió la plancha?? Y porque aguantó después de ser soldada???
i .worked with a friend at hights that used to tack weld without a helmet always said he shut his eyes in time . he was blind 1 year latter with burns to the back of his eyes DONT DO IT
good video ...unfortunately the comments below tell me they do not understand the physics of welding....or just professional whingers
Try adding stiffeners on the edges and sides. Think like a c section piece of steel bent into your s shape. It will make the piece much stronger and safer and still allow the clearance you need. Be safe friend.
another thing I love about this video is the absence of background music..
Amigo con la viga doble t tienes la solución no trabajas tanto y no gastas material
Useful tool...truck springs have a very high carbon content....the spring broke where the heated area was embrittled.
That's right
Just needed annealing, that happened when he welded that piece back, 7018 ? I guess?
@@billarroo1 7016
Yup I seen that coming when he never dipped it
@@timwegman5776vfñhmmnnh
همه مطالب عالی، متنوع، آموزنده و درحد سپاسگذاریست، پرسی از همه دوستان
for the top piece, you could have unscrewed the top extender and made a hole to fit the shaft then replace the extender. that is most secure.
Sucesso
It sucks when it breaks after you have it painted up nice.
I see that someone also noticed the faulty
Procedure that destroyed the jack seals and
Left the metal in quenched . Good idea
But wrong procedure. Some one please
Educate this man .. help him !!
Jack from center of container,or make sure you have a level pad,before ever setting container,those containers dont have much flex.
Вот кусок швеллера от реж уже готово всё по деаганали лишнее от реж и всё гнуть ничего не нужно
that paint made all the difference
Great video. No annoying music, no superfluous voiceover "explanation." Just a guy who knows what he's doing. Also, oxy-acetylene rocks.
,,,CON UNA GATA DE TIJERETA DE SOLO TRES TONELADAS Y QUE SON BIEN BAJITAS , ,,,, LA PONES POR EL OTRO LADO QUE SE VE QUE TIENE ALTURA Y NO TE HUBIERA COSTADO TANTO ......
Love this. My wife is Korean, and when we take trips to see the family I think I get an ulcer every time. They are the most care free thinkers around. All they tell me is ....Ahh it's ok don't worry.
Worrying about what? Seems like you're the wife. :D
@@alphaforce6998 Ah look it's another guy on the internet lonely because he has no friends. Trolling to make a funny. Did you Nut?
@@Helmet_Tester Are you so insecure that you require the perceived validation of other people to feel adequate?
Отлично приспособление. Желаю вам удачи и терпения.
@@choigotv001 друг я с Казахстана,если когда не будь будешь здесь, напиши встречу.
At 13:26 😂😂😂
Удачи любви и терпения все пока ваш нагиев
nice video!👌
The best thing I have seen is the straight edge guide for the cutting torch.
Doesn’t give up easily does he 👍👍👍👍
아주 좋은 아이디어네여...
해외에서는 컨테이너 개작 창고나 집을 많이 하니까..인기가 있군요.
How to make work unsafely? Don't put your hand under the container when lift. Or whatever, you can put your head next time.
변형 아이디어에 특출나신 분이십니다. 그동안 각고의 노력으로 해박한 지식과 역량을 갖추느라 얼마나 고생을 하셨을지 눈에 선합니다.
@@choigotv001 기술이나 인격에도 품질과 수준이 있게 마련이지요. 앞으로도 놀라운 실력 발휘해주시기 바랍니다.
На шток цилиндра происходит односторонняя нагрузка - или шток будет согнут, или направляющая станет овальной и масло будет течь.
Красавчик! Для решения конкретной задачи пойдёт. Тем более поднимает не все 5 тонн, а только угол и кратковременно ;)
@@АндрейНазаров-п4й, домкрат должен оставаться таким, как им он был "таким он и остался". Когда тяжёлая единица поднимается, точка опоры перемещается - ещё больше нагрузка на шток, чем сам вес и, если не ошибаюсь, в конце ролика, шток возвращался с трудом.
Nice