My very first job in 1972 involved operating Arburg 150- 200 all-rounders. Early Arburgs only had 5 fill speeds, and one injection pressure setting. Learning on a machine with limited parameter controls really hones your molding and troubleshooting skills to eventually advance to the size and type seen in this video. Arburgs are the best machines to operate.
Äh......bessere Lösung?! Das Drahtgestell? bei 2 K ?! Wenn ich die Einheit nach oben fahre, ich rechne damit die kommt mir von oben entgegen. Das war das Negative. Positiv : Einmal richtig eingestellt läuft die voll durch. Nach fast 30 Jahren Kunststoff mag ich die "Kisten" aus dem Schwarzwald. Aber , verbaut die Maschinen nicht so sehr. Wenn ich einen Kopfstand machen muss,um den Auswerfer zu entriegeln.Das macht ihr nur,um mich zu Ärgern.:-))))))))
I don't understand. The caps go up a machine to be dropped into another machine, that lifts up the caps so that they can be put in a row so that they can drop freely into a box?
+udo krause Which are synonymous only samples. It is with millions of parts always one with errors thereby.Passiert synonymous with Arburg.Trotz Camera! Not a clue what you're saying even with Google Translate.
Would have liked to see more information given in the video. Is there more than one feed of plastic, where are the plate lines, is there any quality control, how are the caps coloured etc?
How does the speed works so fast, is their any boosters was given with this type of machine or something else that i don't know about this because i am also a basically plastic moulding manufacturing.
Wait, why do the caps have to travel through so many belts and machines just to be put into a box in the end....unless there are some quality checks along the way that i didnt see?
+NumberSixteen BusShelter Yes, indeed: Quality control is the keyword here. We kindly ask you to contact your local ARBURG representative (which you can find here) to find out more.
+NumberSixteen BusShelter The caps are being aligned by the mechanisms that you see, and then set up in "single file", oriented so that a camera system can examine each individual piece. Defective parts are automatically kicked off the conveyor.
Thanks for your comment +Martijn Janssen ! We appreciate your interest in our products and Services. For individual Support kindly contact your local ARBURG application specialist. The contact and address details can be accessed here: www.arburg.com/en/company/locations/
You may have noticed the caps drop down into a hopper. There is conveyer taking them up and to the rear single file and oriented in the same direction, then dropped into collection hopper. While this is all going on they are cooling down. In the past, they were dropped into a hopper where the operator would pick parts up, clip the parts off of the runner and throw in big box. On this machine, guard stays closed, the operator does not have to push 2 interlock buttons to cycle the machine. This machine speeds up process greatly.
72 My dad owned a mold and die shop, had built several 72 cavity cap molds. I worked in the shop for a while, drilled a lot of water lines in the mold base
The clamping force is 3200 kN (320 metric tons) The max. shot weight with the used size 3200 injection unit (according to Euromap) with screw diameter in PS is 1.860 grams
nyc. thnks.sir suggest me the tonnage of a machine which I shld. use for the product weights ranging from 70gms to 140gms which are ideal in relation to cost effectiveness of the production too.
Thanks for your inquiry. We kindly ask for your understanding that for a professional consultation we ask you to either provide your full contact Details via our Website www.arburg.com/en/contact-form/ or send a message to contact@arburg.com
Is that hydraulic or all electric? What is the injection rate and screw dia? What is the function of that three accumulators? What is cooling time for mould?
@Gwiix The caps fall down from the mould then being transported via a conveying system where they will be cooled down to a final and individual quality inspection (each cap).
I am interested in making some packaging for farm products , like jam jars , and I like controlling a process from start to finish . In other words I want to make my own molds . It would be very help full to have a list of the minimum size mills that would be a good choice for a given size of injection molder . For example: for this size ARBURG molding machine , these 6 CNC mills from these 5 companies would be a good match. I understand this kind of list will never be perfect , but even a imperfect list would be a tremendous help in my financial and building planning .
+The Real Plato There are various technical solutions for demoulding screw caps. Feel free to contact your local ARBURG application engineer for further details. www.arburg.com/en/company/locations/
+The Real Plato For threads like this they use a rotating core. External threads can sometimes be molded without rotating cores, but that requires the parting line to split through the threads
PP? Wenn du Fäden hast,Temp runter...oder Scheckenrückzug weiter rauf.Ich würde erst einmal die Temperatur runter nehmen.Pass halt auf, dass die Teile noch voll sind.Wenn Du Themp. an der Maschine hast gehe erst einmal damit auf 5 grad runter.Sollten eigentlich die Fäden weg sein.Oder drehe die Kühlung weiter auf.Die Arburg Maschinen Petzen gern ,was du verstellst zeigt die Schüssel im Protokoll an.Kanns´t du aber übergehen.
#apenas dois jogadores +China Promising Mold Plastic Co,.Ltd. Thanks! We appreciate your comment and feedback! Meet ARBURG at Chinaplas 2016 in Shanghai at Booth E1.G01. @Dung Master
We kindly ask for your understanding that this kind of data is not available. Still we are wishing you all the best for your successful diplom project!
the press has a sensor in it. if to much pressure is required to close the mold. it alarms out and a tech has to remove the part and restart the press. some times on some machines the part actually can get stuck in the mold and get shot over making what we call a "double shot"
The machine on display had 320 metric tons. Information on the screw cap is available here www.arburg.com/en/solutions/injection-moulded-parts/screw-caps/ For more details on your question please contact your local ARBURG subsidiary/trade parther which you can conveniently locate on our website: www.arburg.com/en/company/locations/ Feel free to subscribe to your UA-cam channel and our Google+ profile.
1 year later : - shot weights depends directly from the caps you want to have, usually it's = (weight of the final cap)×(number of cavities), with hot runners and obturation. - rate and melting temperature depends on the raw material you're using. For the same type of material (PP or HDPE), you can have multiple settings depending on the plastic origin. - Mold temperature has to be the lowest possible, temperatures such as 14°C are used. This means faster cooling of the plastic. - once again, ejection temperature depends on the material. It has to be solidified enough to keep its shape during the ejection, but hot enough to "jump" the threads without damaging them. All the parameters you asked are proper to the type of cap, the material and the press used, so there is no typical setting to produce them.
hi, anyone knows what is the meaning of ¨720 H 3200-3200¨, actually i´m working at a plastics facility and we have different models of these ones, thanks in advance.
Thanks for your message. For more details on your question please contact your local ARBURG subsidiary/trade parther which you can conveniently locate on our website: www.arburg.com/en/company/locations/
I have an opportunity to get into an Injection Molding Machine Operator position with a company called Crespac. Is an operator a decent job that pays well in general once you get some experience under your belt? No requirement for using a measuring tape or measuring device was listed in the job description and the manufacturing company is hiring on the spot at their job fair. Do operators need to measure anything with a tape measure/ruler/calipers, for instance? I don't see him doing any of that and it seems like the quality control is within the machine itself that double-checks its work. Can you elaborate on this type of position?
Does Arburg still make the small all-rounder machines? I loved those little guys - had 22 of them in one shop (mid 70's) making electronic connector bodies. Sometimes horiz inject - sometimes vertical.
We have 6 of them at work, probably from the early 80s. CRT screens with green letters on a black background. They are still going strong and are really reliable! A few small oil leaks but nothing more.
+EL AYATI Mohammed Thanks for your kind message. Please contact our French subsidiary for further Information on your subject: www.arburg.com/fr/fr/contact/
+Mitra Utama The difference is the Chinese made machine dumps the caps right into the ocean with the rest of the other plastic pollution generated from Asia.
Thanks for your message: ARBURG's electric, hybrid and hydraulic injection moulding machines for plastics processing cover clamping forces between 125 kN and 5,000 kN. Fields of application include automotive, communications and consumer electronics, medical technology, domestic appliances and packaging. The product range is completed by robotic systems, complex projects and other peripherals. More details on our website: click on "solutions"
Could you offer me a raw material liquid silicone components, to produce membrane. Where did you buy them and what was their trade name? Can you give me any contact or your silicone raw materials name? A and B component etc.
I like this machine very much, I would like to buy one for my factory, but I have one question? how do you type the logo on the cap? and who can I contact for price and other details? Thank you.
The mold alone costs hundreds of thousands of dollars to create (from design, initial fabrication, testing, possible refinements, final approval, etcetera). That entire machine was likely millions of dollars. Probably more than $50 million.
it would benefit the planet if they illegalized caps which are not attached to the bottle. it would improve recycling too because they would get all the cap plastic back.
Thanks for your comment. On the ARBURG website you see in the left column the navigation point "Jobs & Training Opportunities" where you will find further information on available job openings and trainings. Greetings from Germany!
Thanks for your message. ARBURG's main product is injection moulding machines and integrated automation - allowing for turnkey projects including moulds from partner companies.
We have all these regulations and laws that we have to follow, but none of them say we have to put these in a recylcler bin instead of the trash which goes to landfills and never breaks down.
it is just so fucking stupid. Someone need to clearify throing trash in the wrong bin ist harmful for the heath. then you need a lot of medial addention - and finaly you have you regulation. Just soooooo fucking stupid.
the problem has been solved. single source recycling where they separate all the trash at the dump. trash companies are profiting from it big time and china is buying the recycled materials.
Hello! - this is a great machine!! I will start a company in this domain, and I have some questions for you. 1. What is the price of this machine? 2. you can send them in Romania (what cost?)? 3. what is the cost of mentenance? 4. The mould are changable? Thank you!! Regardes, Marian D.
I'm surprised this is a cost effective way to make these things. It must take a lot of electricity to run it and I'd be surprised if they got a penny a cap. I guess if they did get a penny a cap it would be $864 an hour worth of caps... Ok that's pretty good. Although I'd bet they get more like 1/4-1/2 a penny per cap.
My very first job in 1972 involved operating Arburg 150- 200 all-rounders. Early Arburgs only had 5 fill speeds, and one injection pressure setting. Learning on a machine with limited parameter controls really hones your molding and troubleshooting skills to eventually advance to the size and type seen in this video. Arburgs are the best machines to operate.
Hydraulic brakes?
The sounds make my body hairs stand in pleasure. This is literally music for me. I would love to record this and make an album out of it.
In the late 80s we were running the two-shot Arburgs, making phone keypads. They were really good reliable machines, I loved them.
Thank you very much for your kind comments! We much appreciate this and use it as motivation on our continued journey for even better solutions.
Äh......bessere Lösung?! Das Drahtgestell? bei 2 K ?! Wenn ich die Einheit nach oben fahre, ich rechne damit die kommt mir von oben entgegen. Das war das Negative. Positiv : Einmal richtig eingestellt läuft die voll durch. Nach fast 30 Jahren Kunststoff mag ich die "Kisten" aus dem Schwarzwald. Aber , verbaut die Maschinen nicht so sehr. Wenn ich einen Kopfstand machen muss,um den Auswerfer zu entriegeln.Das macht ihr nur,um mich zu Ärgern.:-))))))))
Worked in a foundry for over 40 years never seen such a clean floor
really? in medic industry this is quite generall
Absolutley amazing! What a marvel to behold such an advanced piece of machinery such as this. Science and technology for the win!
+M. Pulverman chill, yo. No need to play the name game on something so insignificant.
Nice. I like seeing good old KTW-molds running smoothly as that.
Cheers from Waidhofen.
KTW molds are not old... u moron
If our arburg allrounder would repeat accurately it would be my favorite machine
Arburg, oh how I miss you 😢
I don't understand. The caps go up a machine to be dropped into another machine, that lifts up the caps so that they can be put in a row so that they can drop freely into a box?
The caps go through some quality control prior they end up in the final box.
die sind auch nur Stichproben.Es sind bei Millionen von Teilen immer eins mit Fehlern dabei.Passiert auch bei Arburg.Trotz Kamera!
+udo krause
Which are synonymous only samples. It is with millions of parts always one with errors thereby.Passiert synonymous with Arburg.Trotz Camera!
Not a clue what you're saying even with Google Translate.
100 % gute Teile sind auch bei Arburg nicht möglich.
I was thinking the same exact thing, but quality control makes sense
Would have liked to see more information given in the video. Is there more than one feed of plastic, where are the plate lines, is there any quality control, how are the caps coloured etc?
Arburg is on another level, but this mould is superb, just to say...
How does the speed works so fast, is their any boosters was given with this type of machine or something else that i don't know about this because i am also a basically plastic moulding manufacturing.
Wait, why do the caps have to travel through so many belts and machines just to be put into a box in the end....unless there are some quality checks along the way that i didnt see?
+NumberSixteen BusShelter Yes, indeed: Quality control is the keyword here. We kindly ask you to contact your local ARBURG representative (which you can find here) to find out more.
+ARBURGofficial Good job not answering the question at all.
Leigh Murray Thanks for your message. Here's the missing link: www.arburg.com/en/company/locations/
+NumberSixteen BusShelter The caps are being aligned by the mechanisms that you see, and then set up in "single file", oriented so that a camera system can examine each individual piece. Defective parts are automatically kicked off the conveyor.
part dropped in into the box, monitor is attached into the machine, it will check the quality for each and every part ?
it's just so odd to see such an incredibly well-engineered, and very complex piece of machinery dedicated to just bottle-caps, something so mundane.
Ich kenne die Jungs noch in grün
Caps are also well engineered.
The reason we can think of bottle caps as mundane is because there are machines like this to manufacture them so quickly and inexpensively.
Water is life.
Weight of each cap in this video?
Is this a strip mold?
Really great job no matters 72 caps or 90 caps. More production in least time fantastic is this fast growing population. Good for China and India
After the moulding process, how do you prevent the products from going al over the place?
Thanks for your comment +Martijn Janssen ! We appreciate your interest in our products and Services. For individual Support kindly contact your local ARBURG application specialist. The contact and address details can be accessed here: www.arburg.com/en/company/locations/
You may have noticed the caps drop down into a hopper. There is conveyer taking them up and to the rear single file and oriented in the same direction, then dropped into collection hopper. While this is all going on they are cooling down. In the past, they were dropped into a hopper where the operator would pick parts up, clip the parts off of the runner and throw in big box. On this machine, guard stays closed, the operator does not have to push 2 interlock buttons to cycle the machine. This machine speeds up process greatly.
hi!
the mold is using Ultra SideGate technology?? or Ultrasync?? none of them ?
who made the mold??
tank u
yes do yall have a purging video?i need to learn how to purge machine when molds mess up ty
how many cavities? what is the cap weight? is it short or long neck? how many knurls for the cap?
72 My dad owned a mold and die shop, had built several 72 cavity cap molds. I worked in the shop for a while, drilled a lot of water lines in the mold base
Einsprizgeschwindigkeit zu hoch.
what happened to the shop??
still working?? is it closed??
where is it??
awesome.sir can u please guide that what is tonnage of the machine and what is maximum short weight it can give in polypropelene.?
The clamping force is 3200 kN (320 metric tons)
The max. shot weight with the used size 3200 injection unit (according to Euromap) with screw diameter in PS is 1.860 grams
nyc. thnks.sir suggest me the tonnage of a machine which I shld. use for the product weights ranging from 70gms to 140gms which are ideal in relation to cost effectiveness of the production too.
Thanks for your inquiry. We kindly ask for your understanding that for a professional consultation we ask you to either provide your full contact Details via our Website www.arburg.com/en/contact-form/ or send a message to contact@arburg.com
thanks.i ll surely do as I m very much interested in an arburg product.
Работаю на этих машинах!!! Все супер!!! И сервис хороший!!! Лучшие на рынке!
Is that hydraulic or all electric? What is the injection rate and screw dia? What is the function of that three accumulators? What is cooling time for mould?
@Gwiix The caps fall down from the mould then being transported via a conveying system where they will be cooled down to a final and individual quality inspection (each cap).
What is the costing of your 180 ton machine
Sliding dog leg, for two piece tread formation... no planetary gear system... I can see how it would speed up things, Whts your plastizing rate.
The caps have a shallow draw and rounded thread. I'm pretty sure the ejector pins just force it off. No need to unscrew.
rounded thread??????????????????????????????????
@tx giorgi u r all right
I am interested in making some packaging for farm products , like jam jars , and I like controlling a process from start to finish . In other words I want to make my own molds . It would be very help full to have a list of the minimum size mills that would be a good choice for a given size of injection molder . For example: for this size ARBURG molding machine , these 6 CNC mills from these 5 companies would be a good match. I understand this kind of list will never be perfect , but even a imperfect list would be a tremendous help in my financial and building planning .
Why don't the threads on the cap get stuck on one half of the mold? Wouldn't you have to screw each cap off?
+The Real Plato There are various technical solutions for demoulding screw caps. Feel free to contact your local ARBURG application engineer for further details. www.arburg.com/en/company/locations/
+The Real Plato For threads like this they use a rotating core. External threads can sometimes be molded without rotating cores, but that requires the parting line to split through the threads
Bei Nadelverschluss-Düsen gibt keinen Faden
PP? Wenn du Fäden hast,Temp runter...oder Scheckenrückzug weiter rauf.Ich würde erst einmal die Temperatur runter nehmen.Pass halt auf, dass die Teile noch voll sind.Wenn Du Themp. an der Maschine hast gehe erst einmal damit auf 5 grad runter.Sollten eigentlich die Fäden weg sein.Oder drehe die Kühlung weiter auf.Die Arburg Maschinen Petzen gern ,was du verstellst zeigt die Schüssel im Protokoll an.Kanns´t du aber übergehen.
#apenas dois jogadores +China Promising Mold Plastic Co,.Ltd. Thanks! We appreciate your comment and feedback! Meet ARBURG at Chinaplas 2016 in Shanghai at Booth E1.G01. @Dung Master
We kindly ask for your understanding that this kind of data is not available. Still we are wishing you all the best for your successful diplom project!
Its just mind blowing speed man and what about GATE? are their any gate on product?
Wonder what screw speed is
86400 screw caps in less than 1 hours, amazing.
hello.. i m really impress with the setup.. few questions...
is there mould safety device.. wat if single cavity or some part is stuck.?
Thanks! Our machinery is equipped with a very fine mould safety device which reacts even with high speeds moulds :)
the press has a sensor in it. if to much pressure is required to close the mold. it alarms out and a tech has to remove the part and restart the press. some times on some machines the part actually can get stuck in the mold and get shot over making what we call a "double shot"
Hello sir
what is tonnage required for 72 cavity and 48 cavity cap mould
The machine on display had 320 metric tons. Information on the screw cap is available here www.arburg.com/en/solutions/injection-moulded-parts/screw-caps/
For more details on your question please contact your local ARBURG subsidiary/trade parther which you can conveniently locate on our website: www.arburg.com/en/company/locations/
Feel free to subscribe to your UA-cam channel and our Google+ profile.
How price?
What is the price of this machine
Good construction molding...good colling and good speed for inject n charge
some threads can be pulled of without damaging the threads, we have some small moulds that fit in small machines and dont use a unscrewing option!
What are the processing parameters for such low cycle time like
Shot Weight -
Injection Rate -
Melting Temp. -
Mold Temp. -
Ejection Temp. -
1 year later :
- shot weights depends directly from the caps you want to have, usually it's = (weight of the final cap)×(number of cavities), with hot runners and obturation.
- rate and melting temperature depends on the raw material you're using. For the same type of material (PP or HDPE), you can have multiple settings depending on the plastic origin.
- Mold temperature has to be the lowest possible, temperatures such as 14°C are used. This means faster cooling of the plastic.
- once again, ejection temperature depends on the material. It has to be solidified enough to keep its shape during the ejection, but hot enough to "jump" the threads without damaging them.
All the parameters you asked are proper to the type of cap, the material and the press used, so there is no typical setting to produce them.
hi, anyone knows what is the meaning of ¨720 H 3200-3200¨, actually i´m working at a plastics facility and we have different models of these ones, thanks in advance.
New at this , how much would it cost to develop a mound ?
what is the injection time on a 720s
How much is this machine please?
Hi ..This machine available in india ? And how many price in indian rupee...give me answer ARBURG ..
comparing with Compression Molding - cost effectiveness?
Thanks for your message.
For more details on your question please contact your local ARBURG subsidiary/trade parther which you can conveniently locate on our website: www.arburg.com/en/company/locations/
I have an opportunity to get into an Injection Molding Machine Operator position with a company called Crespac. Is an operator a decent job that pays well in general once you get some experience under your belt? No requirement for using a measuring tape or measuring device was listed in the job description and the manufacturing company is hiring on the spot at their job fair. Do operators need to measure anything with a tape measure/ruler/calipers, for instance? I don't see him doing any of that and it seems like the quality control is within the machine itself that double-checks its work.
Can you elaborate on this type of position?
no ----you don't need a tape measure
Cavity 17 has non fill.
Strip mold?
Does Arburg still make the small all-rounder machines? I loved those little guys - had 22 of them in one shop (mid 70's) making electronic connector bodies. Sometimes horiz inject - sometimes vertical.
We have 6 of them at work, probably from the early 80s. CRT screens with green letters on a black background. They are still going strong and are really reliable! A few small oil leaks but nothing more.
Correction, they are 35 ton Allrounders made in 1989! They look older to be honest..
Injection speed?
hi, how about to be your agent in Morocco if you dont have one, we are in the field more than 24 years
+EL AYATI Mohammed Thanks for your kind message. Please contact our French subsidiary for further Information on your subject: www.arburg.com/fr/fr/contact/
Thank you very much. We appreciate your kind feedback!
what is the difference between arburg and machine from china?
+Mitra Utama The difference is the Chinese made machine dumps the caps right into the ocean with the rest of the other plastic pollution generated from Asia.
The cost....
Thanks for your message: ARBURG's electric, hybrid and hydraulic injection moulding machines for plastics processing cover clamping forces between 125 kN and 5,000 kN. Fields of application include automotive, communications and consumer electronics, medical technology, domestic appliances and packaging. The product range is completed by robotic systems, complex projects and other peripherals.
More details on our website: click on "solutions"
Hello I need a machine like that how much it cost ?
Impressive. I work with some floppy disc dinosaur arburgs that still run like champs.
how many cavities for the mold?
72 cavities = 72 screw caps ;)
ARBURGofficial - Okay cool. Thank you!
Sir
RATE
SIZE
REQUIRED SPACE
is he reducing the cycle time...???/
Could you offer me a raw material liquid silicone components, to produce membrane. Where did you buy them and what was their trade name? Can you give me any contact or your silicone raw materials name? A and B component etc.
We have just got this machine ,(20112023)
السلام عليكم كم سعر الماكينه بالدولار كم حجمها واي صناعتها
Absolutely amazing! what a Auto Line.
+China Promising Mold Plastic Co,.Ltd. Thanks! We appreciate your comment and feedback! Meet ARBURG at Chinaplas 2016 in Shanghai at Booth E1.G01.
+ARBURGofficial
i am very intersted to get 4 injection molding machine like this
please contact me in my email: berrehoumab@gmail.com
+ARBURGofficial
i am very intersted to get 4 injection molding machine like this
please contact me in my email: berrehoumab@gmail.com
+ARBURGofficial
i am very intersted to get 4 injection molding machine like this
please contact me in my email: berrehoumab@gmail.com
Great, and I'm still breaking my back in 12 hour shifts on CCM001 from year 2001... XD
How much it cost?
Price kitna ha mashine ka
I need this machine i all ways lose my bottle caps How much $
I like this machine very much, I would like to buy one for my factory, but I have one question? how do you type the logo on the cap? and who can I contact for price and other details? Thank you.
Hi dear, our robot can pick and place the caps from the injectiob modig machine. Please4 contact me thanks!
نريد شراء ماكينة حقن بولى
I would like to know the price of this machine pls
The mold alone costs hundreds of thousands of dollars to create (from design, initial fabrication, testing, possible refinements, final approval, etcetera). That entire machine was likely millions of dollars. Probably more than $50 million.
An IMD vision system could be a nice merchandising in this video! Nice machine!
how mach you selling
ineed
Im interested to this mold caps "72 screw", ARBURGofficial give me his constructor please?
Meanwhile I'm packing stuff with my hands out from some really old Arburg machines lol
Thanks for your nice comment which will help to further improve our products.
You may also contact our trade partner EM-KONE OY out of Finland for further details.
only 7 water circuits on a 72 cavity hot runner mold. that is a mold setters dream!
Right? Plus you pull up the prior molding profiles. Probably in production by the 3rd shot
Price
720 Die 2 k sind die besten. Respekt
it would benefit the planet if they illegalized caps which are not attached to the bottle. it would improve recycling too because they would get all the cap plastic back.
Please provide me the price
It is very fast. If use Xijiemould , the cycle time could be semilar.
Thanks for your comment. On the ARBURG website you see in the left column the navigation point "Jobs & Training Opportunities" where you will find further information on available job openings and trainings. Greetings from Germany!
Your company need service engineer in vietnam or not?
I want your nember
Sir mai arburg opretor 8355941266
Shivnath Chaudhary
Of the 10,000 caps you just saw, one is a golden child cap, it will fullfil the prophecy and be recycled, there can only be one. lol
send me the price fob algiers please .
Hi. This is so satisfying... Can i use this video for my compilation? I will give you all the credits!
Yeah bro so satisfying to see all the plastic being produced there. Gotta love destroying the world.
Do you only sell injection machine or make this kinds of mould?
Thanks for your message. ARBURG's main product is injection moulding machines and integrated automation - allowing for turnkey projects including moulds from partner companies.
Lukuduku not joking. To validate or believe his point, see the netstal 96 cavity cap mold running on 2.76 secs ( less than 2 grams cap)
We have all these regulations and laws that we have to follow, but none of them say we have to put these in a recylcler bin instead of the trash which goes to landfills and never breaks down.
screw removing
it is just so fucking stupid. Someone need to clearify throing trash in the wrong bin ist harmful for the heath. then you need a lot of medial addention - and finaly you have you regulation. Just soooooo fucking stupid.
the problem has been solved. single source recycling where they separate all the trash at the dump. trash companies are profiting from it big time and china is buying the recycled materials.
Hope someone turned the water on.
Does Arburg have design job openings ? Great video.
How can i learn to operate and work with your machines ?
Hello! - this is a great machine!! I will start a company in this domain, and I have some questions for you.
1. What is the price of this machine? 2. you can send them in Romania (what cost?)? 3. what is the cost of mentenance? 4. The mould are changable?
Thank you!!
Regardes, Marian D.
you are asking really stupid , full of ignorance, questions
If I could take one thing with me to a desert island, it would be this machine.
le prix svp merci de la ligne
I'm surprised this is a cost effective way to make these things. It must take a lot of electricity to run it and I'd be surprised if they got a penny a cap. I guess if they did get a penny a cap it would be $864 an hour worth of caps... Ok that's pretty good. Although I'd bet they get more like 1/4-1/2 a penny per cap.
Gregory Shumaker What other way would there be to make them more cost effective? The only way to make cheap things cost effectively is in bulk.
+Eggsr2bcrushed whittle each one out of a solid block of plastic. Take about 3 hours per cap!!
Run, them 24/7, supported by many other machines just like it. Make money in volume and over the years.
Some slow motion clips and commentary would have been helpful.
Very fast, compliment.
If in the end he knows how to calibrate the pump with Warburg Brobescnl pressure and speed
I wrote to these guys but they dont respond...😑
very fast injection moulding
Wow very fast running this machine, I'm also operator of husky machine arburg machine and cfL machine, ( from Nepal )