Thank you for your video on the binding of the receiver and the Devo7 on my Wakera Master CP ! It has worked for me, I now have my Master CP motor working! I don’t have to dump this heli! Albert
Thank god you share this, i have a Jumper multiprotocol transmiter and i had problems binding It with the drone, i folowed the steps in the video just as if it was that transmiter and It worked just fine. Thanks
Thank you for that video ,I was pulling my hair out trying to follow the instruction of the manual for binding my devo 7 & my Rx 701 and had no success until I decided to check out your video and within a few minutes I had my receiver and my transmitter binded thanks again Danny.A
I have been flying 3 years, and the fix id binding takes me half an hour, and I have never recognized when I was successfull and why. Somehow I missed the thing that after the non fix id bind, during the connection is on, i should set and bind the fix id. Every day I learn something. THX
You beauty! I followed three other tutorials on youtube and couldn't get it to bind. Followed yours, thought having your doing something different, and guess what, its bound :-) Thank a lot pal.
Awesome! Glad to know it worked for you. I only made this video because another person complained it didn't work as the manual stated. I tried other videos and couldn't get it to work as well. Played around for awhile trying different things because I didn't have a backup to use so I was forced to figure out how to get it working again or buy a different setup. Again, I'm so glad to hear this worked for you. Cheers!
Thx man, saved me some time there, picked up a used Devo 7 and never used InfraX for cheap but didnt have a clue how to bind the 2 and the manual of the Infra says nothing about that xD
how do you like the rx701 overall for your quad? just ordered mine from Amazon and currently have the Runner 250, soon to be shelved and building from scratch using the Devo 7 and RX701. Just curious on how it responds and feels. thanks for the vid too
Some people have issues with it, but I haven't so far. It's been a great low cost setup, but I'll upgrade later for additional features the this one lacks. But again, so far I'm not disappointed with it.
Hi, I have Devo 10, will it also work? btw can you please post video or photos on how you connected the channel from RX701 to the flight controller? Thanks alot!
Dear sir im using my devo 7 for a walkera F210 3D, and want to use it on a Storm drone that i installed the RX701 on, and i want to be able to use the transmitter on them both, how do i do that, it is factory setup for the F210 3D, and i don't want to screw that up, can it be set up for 2 individual drones with separate identifications for receiving one that is on and bind with whichever is currently active ? Thanks
Hi. Just wondering where did you get the bind plug? I have a Rodeo 150 with a Devo 7 already. Last night I bought a Rodeo 110 & a F210 both BNF. I never got a bind plug with my radio so I am seriously hoping one comes with BNF models. Any help appreciated.
Awesome to hear that it was helpful for your workshop Raddy Beer! What exactly was the workshop for and about? Id love to know more about it and if I may be of any help in the future.
Most Walkera Devo RX will work but they're associated with the number of channels. So depending on how many channels you need is limited to 7 with the Devo 7 TX. Get a 10 channel TX you'll still be limited to 7 usable channels. A 4 channel RX will work, but your limited to the 4 channels. Hope that helps.
Well I've always used radiolink, got my first Devo recently, so I don't know the menu at all. You flew through the setting on the Devo so fast I couldn't tell what you were doing. Also, I have never heard of a "binding plug" before, is that specific to the Devo receivers?
All I'm doing is holding down the buttons to fast scroll to the bottom of the list. As for the bind plug all it it is is a servo connector with a jumper pins from the negative and signal pins connected together without the power wire.
Danny wonderful video thank you. I have one question for you, hopefully not a dumb one. I pulled my RX from the bird so it is not connected to anything right now. When you plugged the bind plug in, you plugged it into the BAT port on the RX. How do I power the RX if the BAT port is being used by the BIND. I am assuming I can plug the battery into one of the AUX ports, either AUX 1 or 2, is that correct? Thanks again for the info it is invaluable!
PLEASE HELP! at 1:22 did you program the model of the aircraft 'Racer' of did the controller automatically do that from the data received from the aircraft? Thanks!
Can you please help me to bind my jjpro t1 to my devo 7e? I have the last version firmware dsm2 but no signal in to the dron. By the cleanflight if a turn right or left the parameters they move. But nothing happens when I take of the USB cable and I put the battery.
Hello, thank you for sharing the information of the ending I 7 would like you to show the devo7 menu settings, I am unable to arm the engines through it. Thanks,
You're welcome. Glad I could help. The arming status is setup in your flight controller and not through the transmitter. Depending on how it is setup is how you move the transmitter sticks. For example, I use OpenPilot/LibrePilot with my arming status at with the throttle stick to arm with "yaw right".so it depends on how your flight controller is set to arm.
Would this bonding procedure work with binding the Devo 7 with my Walkera F210 3D? I mistakenly deleted the factory settings that came with this transmitter without saving -duh.Thanks.
Hi Great videos helped me so Thanks I need to know how to assign the the switches on my devo 7 I have tried and tried to get the switch on the right side to change the flight modes horizon ect Please can you help As i havent had any replies from Walkera
Sorry for the page reply. I've been busy with work. If the Walkera Runner 250 is equipped with the Devo RX701 Rx then yes, this video will help you bind it with the Devo 7 Tx.
Hey Danny, Thanks for reply. I don't remember. I had problems with it when I got it with my walkera racer 250. I ended up throwing a tantrum and stomping both racer and controller. I purchased a spectrum DX6i and ordered everything to build from scratch. I'm in the air and loving it. This is my first and god its insane!! Thanks for video love how everyone is sharing there knowledge. I would have never been able to build mine without all the help i've found on here!
+me sorry for the late reply and that I couldn't have been of more help. Glad you're in the air and enjoying this amazing hobby! Fly are and most of all have fun! Happy flying!
I don't have am RX801 to test. From what I can tell from the manual canceling the fixed ID and setting it up in the transmitter would be the same. I can't guarantee it will work though as I do not have an RX801. If you do try it please let me know if it does it doesn't work and I'll update the description.
hi thanks danny i got it yes it just binded the same im just trying to get my nighthawk 280 pro set up but i new to this lol i was setting up my receiver but my pitch & yaw is reversed how do i change that danny and when im on motor testing its singing & bleeping away but dosnt stop and only getting 1-2 motors starting up will this be bad motor calibrations or somthing else lol
+William Davie Preferably you would change the reverse settings in your GCS. If your unable to change it there then you can go to the FUNCTION setting on the Devo 7 and select the first OPTION REVSW. From there can can choose NORM or REV for ELEV, AILE, THRO, and RUDD.
+Danny Om thanks Iv got my receiver bond and fitted in my nighthawk plugged in to baseflight and everything looking good but my aux2 move,s with my throttle lol and I'm still having problems with my calibrations as I can't get all my motors starting up and a few others have told me to flash it with cleanflight these ARF quads ar a nightmare to set up when you haven't got a clue what your doing lol
hi i have the wizard ts215 but i have tried what u did and it does not work but the receiver is different its little . nothing works ive been on and off trying for a year now every video i can find and nothing works
The l.e.d. on the rx isn't flashing any more but I'm not getting any response from the quad. I am very new to this and am trying to get into this hobby and would really appreciate any feedback as to how to get this thing flying. Thanks!
+Dusty Johnson what setup do you have and what troubleshooting have you done? Is the receiver and transmitter bound? Are you getting any channel movement in your flight controlled software? You can also connect a servo directly to a channel and text 3 it there to see if it's properly bound.
My brother there is any way we can get to an arrangement so I can install deviation. And finally be able to fly my jjrc x1 and the jjrc p200 I'm willing to pay
Please can you help I have made 2 wlkera 250 runners The problem Is i can bind 1 of them but the other will not ,and unless i do the whole binding thing again with the other one i cant fly it How can i bind the 2 to the same Devo 7 transmitter Many thanks
You can bind 2 receivers by making sure both Fixed ID codes are the same. But be are if you have both receivers powered on at the same time they will both operate simultaneously as well.
When I connect my bind plug to the batt port and connect power the led blinks fast. Ignored it and followed all your steps but no success. Seems no matter what I do the red led blinks fast. Any suggestions?
How is your receiver wired? Are you sure there's nothing wrong with your bind plug? Like the wire is making the appropriate connection? You could test the continuity of the bind plug to the is not the problem with a multimeter.
My stick is being handled properly yet no weapon on board everything is okay, but I can not arm, I suppose it's radio settings. I'm lost without knowing what to do.
Hello Danny I saw the video on binding Devo-7 to RX701, very good but could you do the same for me except the Devo 7 binding with walkera master CP helicopter and the RX2637H-D receiver. I really would appreciate it I have had the master CP for about a year and never got it off the ground. out of the box I thought i would just take a look and i must have messed up
Sorry for the page reply. I've been busy with work. I don't have that specific receiver Ronnie Anders. But I will see if I can locate an inexpensive RX2673H-D to help you out.
Great ideo I have a problem i hope you can fix I have done all what you have mentioned the problem none of the switches are now getting reconised I went into multi wii and flicking all the switches nothing happens Even when i load default none Hope you can help as i have cleared the devo 4 times now and still the same I want to be able to enable the buzzer if lost and flight mode switch as well as an arming switch I do hope you can help many thanks Graham
@spooner Graham. It's hard to say what the issue is unfortunately. Depending on what channel you're using and what switch you're trying to setup. I don't use Multi Wii so I'm sorry that I can't help you there.
Purchased from HeliPal. Mine are rated at 4S and I have them wired in parallel. Here's a link to their website for LEDs. I didn't link it to any one specific as you may run a 3S or may like other colors or styles that they have to offer. www.helipal.com/multi-rotors_led-lights.html
Yes, the Devo 7 does have failsafe. The default value setting is for it to "HOLD". It can be found in the manual on page 34 for Helicopter and page 66 for Airplane.
im new to this and having one of these...i got through the first little bit of steps...but cant get to the part to run it so it actually binds...i hope i havent changed ant settings on my radio...i just need the basic ones so i can learn to fly it firsrt
+Dale Gann sounds like you're having an issue trying to do fixed ID. Fixed ID isn't necessary, but it allows you to turn on your transmitter and quad right away and fly. Without Fixed ID you have to wait like 10 of 15 seconds for the trim on the screen to stop scrolling to bind. Just takes more time.
Danny Om ....ok I got it figured out...I got the motors going.. appreciate your help dude...if I have anymore questions I'll give u a shout...thanks again
Sorry for the page reply. I've been busy with work. Do you have the receiver wired correctly for power? Mod information would help on trying to resolve this if you haven't given up on it yet.
Dale Gann as long as you're using The Devo 7 and a compatible receiver like The RX701 connected to the flight controller (PWM - one signal wire per channel) then yes, it will work. It will not bind with other manufacturers receivers such as FrSky or Spektrum.
I feel like you went way too fast with the first step. Some of us haven't used a devo 7 before. I heard you say "turn off the fixed ID" and then go through a long button mashing series that made no sense to me. I tried to go to the manual to go through those steps but ended up with a transmitter that gives me an error message when I turn it on. Could you slow down please?
Danny Om, thank you. I went through the steps and I'm still having problems. I may be blinded by frustration. I'll put it to bed for now and try again tomorrow.
+Danny Om I did this and I messed up the settings already installed for my 350pro. Can you show how to connect multiple acft in the menu sys. Example when I'm done with the 350pro I want to fly my racer. How do I switch from one acft to another?
hiya danny sorry this is me just getting back to this i tryed the set up in cleanflight but i wasn,t having any luck iv changed a few things and i think am getting closer haha iv got it on the right stickmode but i just cant get my pitch and roll swapped round when i push my roll its working my pitch and pitch moves my roll and pushing roll to left makes pitch go up lol i cant seem to get these two channels swapped round i even tryed swapping the plugs on the receiver danny i added a video as i was setting it up last week in cleanflight if you want to take a look at it but its a bad video lol this is new to me making video but i was going to make a better one more clearer do you have a video walk throw of your settings or setup for your devo 7 tx& rx and need to work out how to add my failsafe to my gear switch as well danny can you help me out with this if you can danny
+William Davie I haven't used my Walkera transmitter or receiver in months. It's been replaced by a FrSky Taranis X9D Plus. It sounds like you have the pitch and roll reversed on the receiver. I know you said you already tried swapping them with no success. But try this. If you have a servo plug it in to the throttle channel and move the stick to confirm it works. If it doesn't then there's more troubleshooting to be done. If it works them move it to the pitch and move the pitch stick. Keep doing this until you've identified each channel with the correct wires. This will also help you identify the correct wire for the gear channel so you assign it to your failsafe. Hope this helps.
iv got my petrol nitro helicopter here and iv unplugged the swash plate servo wire i can use that yeah ? lol thanks very much danny i love it when a plan comes together my friend i can use that lol wooohoooo haha hey i got a great deal on two flouren 3s 1300mAh batterys i ordered them 2 days ago and they come today they ar ideal for your transmitter danny iv took a photo of them on the order sheet and if your intrested you can look at them on ebay the details ar on the sheet or i can sent you the purches link or page from ebay if your intrested danny and ill add the photo on my page for you to look at but ill go make myself a coffee and get back to this problem solving my friend and thanks very much for the help and tips awesome my friend your the man danny thanks a lot
+jake2184 Hey man sorry for the late reply I was in Asia. Check to see that you have the wires all in the right place. I brought mine to a hobby store and the guy helped me out with mine. He got my LED's on then I was able to bind it following this video!
i followed every step..but right after i pull the reset plug out of my srd250 while its live..i would still get a fast flashing red light...my devo 7 was reset..ANY IDEAS OR ADVICE..DRONE NOOB..LOL
soaringman step by step details are in the description. I just made the video quickly to show how to do it originally for someone. Sorry for not explaining the entire video of each step and why. I never expected it to help so many. And I just held the buttons down to scroll quickly.
thanks, i get red light to come on solid but cant arm drone. it was working before but i tried to upgrade using librepilot when i did the transmitter set up part i may have done somthing bad. is it posible to reset devo7 to factory settings?
My Devo 7 is a waste of money. Brand new and it can not bind to my Walkera 250 Racer with an rx 701 or my Walkera 350 Pro with an rx 703. I'm going to burn $1000 worth of equipment in a pit. I wish your video instructions would have worked for me.
I went through the binding process for all of the equipment (all bought separately, bnf) and cannot arm the motors for either. There are no vids for the correct pin outs for the rx and the Chinese manuals are not even worth their weight in toilet paper.
Thank you for your video on the binding of the receiver and the Devo7 on my Wakera Master CP !
It has worked for me, I now have my Master CP motor working!
I don’t have to dump this heli!
Albert
Thank god you share this, i have a Jumper multiprotocol transmiter and i had problems binding It with the drone, i folowed the steps in the video just as if it was that transmiter and It worked just fine. Thanks
Thank you for that video ,I was pulling my hair out trying to follow the instruction of the manual for binding my devo 7 & my Rx 701 and had no success until I decided to check out your video and within a few minutes I had my receiver and my transmitter binded thanks again Danny.A
+Henri bedard very happy to hear it worked. Sounds like you had no problems following the video/description. Again. Happy to hear I was able to help.
I have been flying 3 years, and the fix id binding takes me half an hour, and I have never recognized when I was successfull and why. Somehow I missed the thing that after the non fix id bind, during the connection is on, i should set and bind the fix id. Every day I learn something. THX
i advised my students to buy devo 7 and rx701 for a quad.
we build 4 of them during a workshop. i gave them this link how to bind. nice clear vid.
Awesome and thank you for the recommendation for them to work with the Devo. If there anything I may do to help you please don't hesitate to ask.
You beauty! I followed three other tutorials on youtube and couldn't get it to bind. Followed yours, thought having your doing something different, and guess what, its bound :-) Thank a lot pal.
Awesome! Glad to know it worked for you. I only made this video because another person complained it didn't work as the manual stated. I tried other videos and couldn't get it to work as well. Played around for awhile trying different things because I didn't have a backup to use so I was forced to figure out how to get it working again or buy a different setup. Again, I'm so glad to hear this worked for you. Cheers!
Thanks again Danny. Yeah the other three videos I watched before yours it wouldn't bind, yours, straight away. Thanks again.
+Danny Om i have a walkera 250 fpv racer after replacing main board i have fast blink tail lights and no response or bind??????? please help
Thank you, sir! I'm looking for "how to bind the RX 70* receiver". Successfully!
Thx man, saved me some time there, picked up a used Devo 7 and never used InfraX for cheap but didnt have a clue how to bind the 2 and the manual of the Infra says nothing about that xD
Excelente, gracias a tu video pude echar a volar mi RUNNER. Gracias
Thank you so much I’ve been looking for a video exactly like this
how do you like the rx701 overall for your quad? just ordered mine from Amazon and currently have the Runner 250, soon to be shelved and building from scratch using the Devo 7 and RX701. Just curious on how it responds and feels. thanks for the vid too
Some people have issues with it, but I haven't so far. It's been a great low cost setup, but I'll upgrade later for additional features the this one lacks. But again, so far I'm not disappointed with it.
Hi, did you set the toggle switches and quadcopter control keys in Betaflay at the transmitter?
Hi,
I have Devo 10, will it also work?
btw can you please post video or photos on how you connected the channel from RX701 to the flight controller?
Thanks alot!
Dear sir im using my devo 7 for a walkera F210 3D, and want to use it on a Storm drone that i installed the RX701 on, and i want to be able to use the transmitter on them both, how do i do that, it is factory setup for the F210 3D, and i don't want to screw that up, can it be set up for 2 individual drones with separate identifications for receiving one that is on and bind with whichever is currently active ? Thanks
Thanks Danny, finally a video that actually works, good man
Thank you for the comment. Glad it worked for you MrMakjak001.
Clear 🎉🎉🎉Thank you so much.
Hi. Just wondering where did you get the bind plug? I have a Rodeo 150 with a Devo 7 already. Last night I bought a Rodeo 110 & a F210 both BNF. I never got a bind plug with my radio so I am seriously hoping one comes with BNF models. Any help appreciated.
HELLO, thanks for the video,it worked out good for me just as you instructed. question? is that a runner frame,and ware can i get those lights at.
thanks was the rx that fits on a walkera 250 runner?
I think It is, i have the devo rx 710 in the walkera and It worked
I use this vid during our workshop
Awesome to hear that it was helpful for your workshop Raddy Beer! What exactly was the workshop for and about? Id love to know more about it and if I may be of any help in the future.
I did, was the setting on the controller board software, however, can not use the other command keys to program in failsafe, point of interest etc.
Thanks for the video. It was a huge help.
Which port is powering the RX701 receiver? ...because my ESCs are the Opto type without any BEC.
You can power the receiver through any channel as long as you have the correct voltage.
Hi danny, any recommended rx other than RX701 for devo 7 transmitter? thanks!
Most Walkera Devo RX will work but they're associated with the number of channels. So depending on how many channels you need is limited to 7 with the Devo 7 TX. Get a 10 channel TX you'll still be limited to 7 usable channels. A 4 channel RX will work, but your limited to the 4 channels. Hope that helps.
Awesome. Thanks so much for this.
Glad to hear it worked for you Cent Dental. Makes me happy to know I'm able to help others.
Well I've always used radiolink, got my first Devo recently, so I don't know the menu at all. You flew through the setting on the Devo so fast I couldn't tell what you were doing. Also, I have never heard of a "binding plug" before, is that specific to the Devo receivers?
All I'm doing is holding down the buttons to fast scroll to the bottom of the list. As for the bind plug all it it is is a servo connector with a jumper pins from the negative and signal pins connected together without the power wire.
Danny wonderful video thank you. I have one question for you, hopefully not a dumb one. I pulled my RX from the bird so it is not connected to anything right now. When you plugged the bind plug in, you plugged it into the BAT port on the RX. How do I power the RX if the BAT port is being used by the BIND. I am assuming I can plug the battery into one of the AUX ports, either AUX 1 or 2, is that correct? Thanks again for the info it is invaluable!
+Ais4Art sorry for the late reply. Thank you for the assist Ais4Art.
PLEASE HELP! at 1:22 did you program the model of the aircraft 'Racer' of did the controller automatically do that from the data received from the aircraft?
Thanks!
+Lachlan Peknice I manually changed the name of the model.
Uhm, when i pull the Plug the Blinking compleatly stopps...
What should i do?
Can you please help me to bind my jjpro t1 to my devo 7e? I have the last version firmware dsm2 but no signal in to the dron. By the cleanflight if a turn right or left the parameters they move. But nothing happens when I take of the USB cable and I put the battery.
Hello, thank you for sharing the information of the ending I 7 would like you to show the devo7 menu settings, I am unable to arm the engines through it. Thanks,
You're welcome. Glad I could help. The arming status is setup in your flight controller and not through the transmitter. Depending on how it is setup is how you move the transmitter sticks. For example, I use OpenPilot/LibrePilot with my arming status at with the throttle stick to arm with "yaw right".so it depends on how your flight controller is set to arm.
Would this bonding procedure work with binding the Devo 7 with my Walkera F210 3D? I mistakenly deleted the factory settings that came with this transmitter without saving -duh.Thanks.
I'm not sure what receiver you're working, but it should work for the RX70X receivers.
THANK YOU.
Could I also use the same steps on an rx 702 receiver?
I'm currently trying to find out which reveiver to use in my quad with a devo 7 transmitter
Yes, it should still work the same.
Thanks!
I just wasn't sure because it always says Walkera QR X350 spare part in the stores I looked at
+ct_57 No worries. Glad I could help you out.
hi, my friend's devo radio will not bind because he forgot what fix id code he used. is there a way to bind it again?
This video was very helpful, I would subscribe if u have more drone videos
Hi Great videos helped me so Thanks
I need to know how to assign the the switches on my devo 7
I have tried and tried to get the switch on the right side to change the flight modes horizon ect
Please can you help As i havent had any replies from Walkera
can I also use this solution for walkera runner 250, have no binding. Tx for u Vid.
Sorry for the page reply. I've been busy with work. If the Walkera Runner 250 is equipped with the Devo RX701 Rx then yes, this video will help you bind it with the Devo 7 Tx.
Where do I get a bind plug? Do I just need to jump/short a couple pins?
+Jordan Wires The bind plug is just a servo plug with a jumper wire from the top pin (signal) to the bottom pin (negative - ). Hope that helps.
HI , thanks for the video. I get the slow flashing red light but when I pull bind plug I get no rapid flashing light. No light at all. Any ideas??
+Thomas W. Brinkley are you inserting the bind plug before you plug in the battery?
Hey Danny, Thanks for reply. I don't remember. I had problems with it when I got it with my walkera racer 250.
I ended up throwing a tantrum and stomping both racer and controller. I purchased a spectrum DX6i and ordered everything to build from scratch. I'm in the air and loving it. This is my first and god its insane!!
Thanks for video love how everyone is sharing there knowledge. I would have never been able to build mine without all the help i've found on here!
+me sorry for the late reply and that I couldn't have been of more help. Glad you're in the air and enjoying this amazing hobby! Fly are and most of all have fun! Happy flying!
Can I bind my Devo 7 with Eachine trashcan DSM2 DSMX version?
hi great video danny om will this devo 7 transmitter bind to the devo RX802 receiver ok will it just be the same as you did in this video danny
I don't have am RX801 to test. From what I can tell from the manual canceling the fixed ID and setting it up in the transmitter would be the same. I can't guarantee it will work though as I do not have an RX801. If you do try it please let me know if it does it doesn't work and I'll update the description.
hi thanks danny i got it yes it just binded the same im just trying to get my nighthawk 280 pro set up but i new to this lol i was setting up my receiver but my pitch & yaw is reversed how do i change that danny and when im on motor testing its singing & bleeping away but dosnt stop and only getting 1-2 motors starting up will this be bad motor calibrations or somthing else lol
and sorry i did it with fixxed turned on aswell some people dose it with fixxed turned of danny
+William Davie Preferably you would change the reverse settings in your GCS. If your unable to change it there then you can go to the FUNCTION setting on the Devo 7 and select the first OPTION REVSW. From there can can choose NORM or REV for ELEV, AILE, THRO, and RUDD.
+Danny Om thanks Iv got my receiver bond and fitted in my nighthawk plugged in to baseflight and everything looking good but my aux2 move,s with my throttle lol and I'm still having problems with my calibrations as I can't get all my motors starting up
and a few others have told me to flash it with cleanflight these ARF quads ar a nightmare to set up when you haven't got a clue what your doing lol
hi i have the wizard ts215 but i have tried what u did and it does not work but the receiver is different its little .
nothing works ive been on and off trying for a year now every video i can find and nothing works
The l.e.d. on the rx isn't flashing any more but I'm not getting any response from the quad. I am very new to this and am trying to get into this hobby and would really appreciate any feedback as to how to get this thing flying. Thanks!
+Dusty Johnson what setup do you have and what troubleshooting have you done? Is the receiver and transmitter bound? Are you getting any channel movement in your flight controlled software? You can also connect a servo directly to a channel and text 3 it there to see if it's properly bound.
My brother there is any way we can get to an arrangement so I can install deviation. And finally be able to fly my jjrc x1 and the jjrc p200 I'm willing to pay
Please can you help I have made 2 wlkera 250 runners The problem Is i can bind 1 of them but the other will not ,and unless i do the whole binding thing again with the other one i cant fly it
How can i bind the 2 to the same Devo 7 transmitter
Many thanks
You can bind 2 receivers by making sure both Fixed ID codes are the same. But be are if you have both receivers powered on at the same time they will both operate simultaneously as well.
cheers danny
When I connect my bind plug to the batt port and connect power the led blinks fast. Ignored it and followed all your steps but no success. Seems no matter what I do the red led blinks fast. Any suggestions?
How is your receiver wired? Are you sure there's nothing wrong with your bind plug? Like the wire is making the appropriate connection? You could test the continuity of the bind plug to the is not the problem with a multimeter.
Actually I fixed it. I took apart the receiver and found a loose solder joint on the batt port. Now it works! Thanks for the reply!
Awesome! Glad to know you have some electronics skill and was able to locate the issue to fix it yourself!
My stick is being handled properly yet no weapon on board everything is okay, but I can not arm, I suppose it's radio settings. I'm lost without knowing what to do.
Hello Danny I saw the video on binding Devo-7 to RX701, very good but could you do the same for me except the Devo 7 binding with walkera master CP helicopter and the RX2637H-D receiver. I really would appreciate it I have had the master CP for about a year and never got it off the ground. out of the box I thought i would just take a look and i must have messed up
Sorry for the page reply. I've been busy with work. I don't have that specific receiver Ronnie Anders. But I will see if I can locate an inexpensive RX2673H-D to help you out.
my walkera qr x 350 mix switch gps hold and RTL don't work I am flying in manual all the time any ideas
Great ideo
I have a problem i hope you can fix I have done all what you have mentioned the problem none of the switches are now getting reconised I went into multi wii and flicking all the switches nothing happens
Even when i load default none
Hope you can help as i have cleared the devo 4 times now and still the same I want to be able to enable the buzzer if lost and flight mode switch as well as an arming switch
I do hope you can help
many thanks
Graham
@spooner Graham. It's hard to say what the issue is unfortunately. Depending on what channel you're using and what switch you're trying to setup. I don't use Multi Wii so I'm sorry that I can't help you there.
What LED's are those, do you have a link or name you can share? I really like them
Purchased from HeliPal. Mine are rated at 4S and I have them wired in parallel. Here's a link to their website for LEDs. I didn't link it to any one specific as you may run a 3S or may like other colors or styles that they have to offer.
www.helipal.com/multi-rotors_led-lights.html
Danny Om Thanks
Rodrigo Cristancho Anytime.
After binding sequence the light is still flashing after the beeps
hi, where i can get these led lights from? cheers
i got the problem..when my transsmiter beep and its conected red light stil flashing quickly...sudenly i cant conected to drone..can you help?
same
Does this RX have fail safe ? I want to use it on APM2.6 .
Yes, the Devo 7 does have failsafe. The default value setting is for it to "HOLD". It can be found in the manual on page 34 for Helicopter and page 66 for Airplane.
im new to this and having one of these...i got through the first little bit of steps...but cant get to the part to run it so it actually binds...i hope i havent changed ant settings on my radio...i just need the basic ones so i can learn to fly it firsrt
+Dale Gann sounds like you're having an issue trying to do fixed ID. Fixed ID isn't necessary, but it allows you to turn on your transmitter and quad right away and fly. Without Fixed ID you have to wait like 10 of 15 seconds for the trim on the screen to stop scrolling to bind. Just takes more time.
the 2nd part ...how to i get to that part to where it says run to start the binding process
+Dale Gann in the description I've listed step by step instructions.
Danny Om ....ok I got it figured out...I got the motors going.. appreciate your help dude...if I have anymore questions I'll give u a shout...thanks again
I pulled out the bind plug but the red light stopped. It's flashing when the plug is inserted. What's wrong?
Sorry for the page reply. I've been busy with work. Do you have the receiver wired correctly for power? Mod information would help on trying to resolve this if you haven't given up on it yet.
What 250 frame are you running?
It's The Storm Racing Drone Type-A or EMax Nighthawk 250.
these steps in your video....can you do these same steps on any racing drone to bind it and the radio with the devo 7
Dale Gann no, this is only compatible with Walkera receivers such as the RX7xx receivers.
I have the devo 7 transmitter
Dale Gann as long as you're using The Devo 7 and a compatible receiver like The RX701 connected to the flight controller (PWM - one signal wire per channel) then yes, it will work. It will not bind with other manufacturers receivers such as FrSky or Spektrum.
Ok
After binding Red rear lights not coming back on
I feel like you went way too fast with the first step. Some of us haven't used a devo 7 before. I heard you say "turn off the fixed ID" and then go through a long button mashing series that made no sense to me. I tried to go to the manual to go through those steps but ended up with a transmitter that gives me an error message when I turn it on. Could you slow down please?
There's a detailed step by step information available if you click the show more.
Danny Om, thank you. I went through the steps and I'm still having problems. I may be blinded by frustration. I'll put it to bed for now and try again tomorrow.
Followed all the steps and can't get it to bind
Danny do another video just the TX menu, you lost me after the you hit three buttons. I had no idea of where you went in the menu sys.
Hi Douglas. I've made a step-by-step walk through guide and updated it in the information area. I hope this helps
+Danny Om Thank you! That will help very much.
+Douglas Strain you're welcome. Hope everything works out for you!
+Danny Om I did this and I messed up the settings already installed for my 350pro. Can you show how to connect multiple acft in the menu sys. Example when I'm done with the 350pro I want to fly my racer. How do I switch from one acft to another?
hiya danny sorry this is me just getting back to this i tryed the set up in cleanflight but i wasn,t having any luck iv changed a few things and i think am getting closer haha iv got it on the right stickmode but i just cant get my pitch and roll swapped round when i push my roll its working my pitch and pitch moves my roll and pushing roll to left makes pitch go up lol i cant seem to get these two channels swapped round i even tryed swapping the plugs on the receiver danny i added a video as i was setting it up last week in cleanflight if you want to take a look at it but its a bad video lol this is new to me making video but i was going to make a better one more clearer do you have a video walk throw of your settings or setup for your devo 7 tx& rx and need to work out how to add my failsafe to my gear switch as well danny can you help me out with this if you can danny
+William Davie I haven't used my Walkera transmitter or receiver in months. It's been replaced by a FrSky Taranis X9D Plus.
It sounds like you have the pitch and roll reversed on the receiver. I know you said you already tried swapping them with no success. But try this.
If you have a servo plug it in to the throttle channel and move the stick to confirm it works. If it doesn't then there's more troubleshooting to be done. If it works them move it to the pitch and move the pitch stick. Keep doing this until you've identified each channel with the correct wires.
This will also help you identify the correct wire for the gear channel so you assign it to your failsafe.
Hope this helps.
iv got my petrol nitro helicopter here and iv unplugged the swash plate servo wire i can use that yeah ? lol thanks very much danny i love it when a plan comes together my friend i can use that lol wooohoooo haha hey i got a great deal on two flouren 3s 1300mAh batterys i ordered them 2 days ago and they come today they ar ideal for your transmitter danny iv took a photo of them on the order sheet and if your intrested you can look at them on ebay the details ar on the sheet or i can sent you the purches link or page from ebay if your intrested danny and ill add the photo on my page for you to look at but ill go make myself a coffee and get back to this problem solving my friend and thanks very much for the help and tips awesome my friend your the man danny thanks a lot
i add you on google+ and added to photo,s of them for you to look at if your intrested danny
I can't get the wiring correct for pwm I'm confused can someone help please?
Hey man i tried this but no luck. I dont see any red lights on the reciever!
+THOMAS TRAN I got it working!! Thanks for the vid!!
+THOMAS TRAN Can I ask what you did? I have no visible LED
+jake2184 Hey man sorry for the late reply I was in Asia. Check to see that you have the wires all in the right place. I brought mine to a hobby store and the guy helped me out with mine. He got my LED's on then I was able to bind it following this video!
Is it multi protocol
No
Hi!
I do the same things and the red light do the same thing that you show, but when i try to start the Dron, he doesnt do anything!
plz Help !
Ignacio Carro Torres sorry for the late reply. If you hadn't gotten it to work yet have you checked to see if you get input commands in your GCS?
Como consguir. O manual do radio,tplink f7 em português.
Hi can anybody help I have a anatec bait boat needs binding to a devo 7
i followed every step..but right after i pull the reset plug out of my srd250 while its live..i would still get a fast flashing red light...my devo 7 was reset..ANY IDEAS OR ADVICE..DRONE NOOB..LOL
Have the same problem... Have you figured out?
The receiver is suppose to flash fast after pulling the bind plug out. When it's inserted before powering it on it should be flashing slow.
+Danny Om thank you for fast answer:))
It is flashing after step 9 and i power it on. How should it flash when its binded?
+anton arnqvist it should be a solid light. You can see at about the 1:05 mark.
+Danny Om gonna try it again
i need help
no interest .. far too fast on buttons therefore you do not undertsand what you do
you npushing buttions like crasy and explain nothing
soaringman step by step details are in the description. I just made the video quickly to show how to do it originally for someone. Sorry for not explaining the entire video of each step and why. I never expected it to help so many. And I just held the buttons down to scroll quickly.
+Danny Om so frustrating for me because I have both units and this will not work
+Danny Om so frustrating for me because I have both units and this will not work
Maybe post a video and I'll see if I can help
thanks, i get red light to come on solid but cant arm drone.
it was working before but i tried to upgrade using librepilot when i did the transmitter set up part i may have done somthing bad.
is it posible to reset devo7 to factory settings?
Danny this is all good but you to all this way to fast to even keep up watching what your pressing and so forth
Yep. That is common. Usually difficult to tell what (buttons) and when they are pressing.
Video way to fast..
My Devo 7 is a waste of money. Brand new and it can not bind to my Walkera 250 Racer with an rx 701 or my Walkera 350 Pro with an rx 703. I'm going to burn $1000 worth of equipment in a pit. I wish your video instructions would have worked for me.
+delloco sorry to hear you're having issues. What exactly is the issue you're having?
I went through the binding process for all of the equipment (all bought separately, bnf) and cannot arm the motors for either. There are no vids for the correct pin outs for the rx and the Chinese manuals are not even worth their weight in toilet paper.
you scrolled so fast, even if I pause, I can't see it. Sorry thumb down \👎
That was mentioned before and I apologize for that which is why I left detailed step by step instructions in the information section.