[TSW2] Stuck on the Grade 1.5% GRADE Sand Patch Grade
Вставка
- Опубліковано 13 лип 2024
- If you need help with getting over the mountain on Train Sim World 2/ Sand Patch Grade. You will need a little knowledge of the engineer panel, and some patience. Hope you enjoy. Don't forget to SUBSCIRBE,LIKE, Click the BELL.
AC4400
SD-40
Need help with the AC4400- • Easy Guide/For the Com...
Need help with the SD-40- • How TO!!! Start the SD...
Need help with the GP-38- • HOW TO!!! Properly Sta...
Learn about the Braking System's- • [TSW2] In-depth Tutori...
**Follow me on Twitch** / lucerogaming0304
** Follow me on Twitter** / andrewl16173621 - Ігри
![[TSW2] In-depth Tutorial of Braking Systems Sand Patch Grade SD-40](/img/n.gif)
The Fully fueled scenario it's something... Especially being slowed down by the train ahead, having to do start and stops along the way, quite challenging
Haven't tried that one yet.
Ya so painful i didnt stop though i saved game and then just hoped for yellow signal. If signals fails then i can again restart from save game and stop this time.
The main reason for failure is not setting up all 4 Lokomotives right with the I think it's called Bank System? So that the first in line controls the last in line
@@ThorAxeTheThunder Funny enough I passed this scenario on the 2nd try. On the first try I over ran the first red light, shortly after the end of the 50 mph zone
@@machintrucGaming then I guess you configured your machines right😁
There's a UA-cam video regarding the Fully Fueled run by Dirty Curcuits, I think that's the name. It explains how you should have the train to train communications established, thereby eliminating this problem.
I don’t know the name of the mission… it’s the same part of the map, but you have four locomotives (two in front, two in back). It’s crazy hard for me
i think your vid are the best i have come across . I have subed
Thanks bro I really struggled at first
No problem!
The 1.9% grade near the top is insane
That's the truth.
There are similarly steep grades on the recently released horseshoe curve route.
@@unknown-xf4ko agreed it’s my favourite route
😂😂 if you think 1.9 is bad try Cajon on Run 8
@rack_9 I just made the switch to run8 a few months back and recently bought the cojan sub and I see what you mean I played both the run8 and tsw versions of the route and that 3% grade is nuts.
Here's what I did:
Before starting the train on the journey, I have the last 2 locos (AC44, gp or SD) set on distributed power and generator to on (AC44) and I have the 2nd to last loco on reverse and for Notch 3 (AC44), Notch 4 (GP and SD). Go back to lead engines and set up the first engine as normal, 2nd engine as trailing and such, and boom! I tackled it all. For the uncouple 2 cars, I walk to the very back of train and shut it down and disconnect with no failure...
Lol thats one way to do it.
@@lucerogaming3720 definitely. It's a long process, but can be done.
Is it possible or legal doing that in real life?
ua-cam.com/video/94HeIU-okhQ/v-deo.html here is how I got up with 164 cars had all engines once I hit the grade to full power 4 engines at front 1 in middle and one at the end.
I got to admit man I've been struggling with getting over that Hill and have watched so many videos just to be frustrated this was the only method that worked for me thanks bud
Nice vid 👍
Thank you!
LuceroGaming np!
I'm at the Fully Fueled Scenario and passed the first part of it. Now, seeing all the coments about this mission, I'm having worries with the steeper part of it (didn't reached yet).
The steeper grade can be a challenge. Try keeping it in notch 7 and you should make it over.
It's actually Dusty Circuits.
i dont have any problems with this trains in TSW 2020, only with SD40-2, that loco has a lot of glitches
The locomotive is an AC, you don't need to worry about "too many amps".
WHEN IT COMES TO TRAINS NOT BEING ABLE TO TOP THE GRADE,YOU MUST REALIZE. FOUR IMPORTANT FACTORS.#1,TONNAGE.HOW MUCH WEIGHT THE LOCOMOTIVES ARE PULLING.#2,SPEED OF THE TRAIN.#3WEATHER CONDITIONS #4, A LACK OF ADHESION.AND THE GEAR RATIO OF THE LOCOMOTIVES.ANY TIME YOU PUT LICOMOTIVES THAT ARE STRICTLY BUILT FOR HIGH SPEED ,AND YOU PUT THESE ON A HEAVY LOW DRAG FREIGHT,WHAT YOU ARE GOING TO GET IS REDUCED TRACTIVE EFFORT AT LOW SPEEDS!LOCOMOTIVES THAT'S GEARED FOR HIGH SPEEDS. SHOULD NOT BE PLACED ON ANY HEAVY, HIGH TONNAGE TRAINS!YOU. MIST REMEMBER THAT IF YOU DO THIS,YOU CAN BURN UP THE TRACTION MOTORS ON A LOCOMOTIVE THAT IS GEARED FOR FAST, INTERMODAL TRAINS.THE REASONS FOR THIS IS THAT THE TRACTION MOTORS WILL BURN UP BECAUSE THEY ARE TURNING TOO SLOWLY TO ABSORB ALL THE ELECTRICAL CURRENT GENERATED BY THE ENGINE AND GENERATOR SET!THE SAME THING GOES FOR A CONSIST OF LOCOMOTIVES WITH DIFFERENT GEAR RATIOS. IF YOU HAVE. A LASH UP LIKE THIS,THE TOP SPEED OF THE TRAIN MUST NOT EXCEED THE TOP SPEED OF THE LOWEST GEARED LOCOMOTIVES! ANOTHER REASON, WET. RAILS. YOU CAN ACTUALLY DESTROY THE TRACTION MOTORS BY RUNNINR ON RAILS THAT ARE SLIPPERY FROM LEAVES,SNOW,AND RAIN. ALSO. A LACK OF TRACTION SAND ALSO PLAYS A PART IN TRAINS STALLING ON THE GRADE. PLUS,YOU COULD HAVE TOO MANY FREIGJT CARS ,AND NOT ENOUGH POWER TO GET OVER THE GRADES. THEREFORE,YOU MUST REDUCE THE TONNAGE.LETS SAY. YOU MAY HAVE TO DOUBLE THE HILL.IN OTHER WORDS AKE ONE SECTION OF THE TRAIN OVER THE GRADE,AND GO BACK AND GET THE REST OF THE TRAIN AND PUT IT TOGETHER. I HAVE SEEN ENGINEERS ACTUALLY SET THETE AND ALLOW THE UNITS TO SPIN UNTIL THE TRACTION MOTORS CAUGHT FIRE!THIS CAN BE AVOIDED IF THE RIGHT GEARED LOCOMOTIVES ARE PUT TOGETHER ON THE TRAIN. NEVER MIX HIGH AND LOW GEARED LOCOMOTIVES TOGETJER AND ATTEMPT TO USE THEM ON A HEAVY TRAIN GOING UPHILL!THIS WILL ONLY LEAD TO LOCOMOTIVE FAILURES AND TRACTION MOTOR FIRES! REMEMBER, HIGH SPEED LOCOMOTIVES ARE NOT ANY GOOD. ON LONG TOUGH HEAVY GRADES!
Where are you getting the AC44s? There are none on my map.
There are a couple of scenarios that make you use those locomotives.
When you play on timetables you can actually pick the locomotive you want to play as.
My trick is this, i have to control at the back of the loco
We’re you located right after hyndman because if so I got stuck in the same spot
Yeah the grade gets steep in that area.
Even steeper at Mance. The way I’m always able to get up the hill is keep at the speed limit
wasn't mance almost 2%
Yeah. I believe it was 1.9%
What if it's raining
Yeah man I'm certain this has been changed or patched or something it's next to Impossible I can't do it
Funnily i just randomly got this game and randomly tried this mission because why not, now I'm stuck going up the grade at 12 MPH 😅 it's so slow
Welcome to Train Sim World 2!
I already know how to just throw it in notch 8 I'm just kidding notch 4 or 5 then get momentum then throw it in 8
Does not work deleting game
If you set the DP properly you should be able to get up the hill on Fully Fuelled
NO!IT DOESN'T WORK LIKE THAT. IF YOU HAVE TWO HIGH SPEED UNITS UP FRONT,AND YOU HAVE TWO DP UNITS THAT HAS THE SAME GEAR RATIOS THAT THE ONES UP FRONT HAS OU WILL NEVER GET THE YRAIN OVER THE GRADE WITHOUT STALLING! HIGH SPEED LOCOMOTIVES ARE ONLY GOOD FOR ONLT HIGH SPEED TRAINS.THEY ARE WORTHLESS WHEN IT COMES TO SLIW,HEAVY TRAINS. THE NUMBER ONE FACTOR,IS WEIGHT GEARING ,AND THE. PERCENTAGE OF THE GRADE. YOU HAVE TO KERP THESE THINGS IN MIND WHEN YOU HAVE A HEAVY TRAIN. GOING UP GRADE. DP IS NOT GONNA HELP YOU IF THE TRAIN IS OVERLOADED WITH TONNAGE .AND THEY HAVE HIGH SPEED GEARING! ALSO OU MUST HAVE AN EQUAL NUMBER OF LOCOMOTIVES BOTH UP FRONT,AND IN THE MIDDLE,AND AT LEAST FOUR MORE ON THE REAR PUSHING THE TRAIN. THERE ARE DANGERS INVOLVED WITH DP. WHAT IF THE DP UNITS RECIEVES A. BAD SIGNAL?AND A MALFUNCTION OCCURS?WHAT YOU WILL GET IS WHEN THW HEAD END UNITS START BRAKING,SLOWING DOWN,AND THE DP UNITS CONTINUES TO PUSH THE TRAIN OU WILL HAVE A MASSIVE DERAILMENT THAT COULD HAVE HAZERDOUS /FLAMABLE LIQUIDS NEXT TO THEM?THIS SPELLS DISASTER FOR RESIDENTS WHO LIVE NEAR TRAIN TRACKS! TJIS IS WHAT HAPPENED TO CSX IN GEORGIA.A MALFUNCTION HAPPENED TO THE LOCOMOTIVE,AND SENT IT OUT OF CONTROL.AND IT CAUSED A BAD DERAILMENT WITH SEVETAL FREIGHT CARE. ON THE GROUND!THIS IS WHY IF AN ENGINEER IS USING A REMOTE CONTROLLED LOCOMOTIVE T IS BEST TO STAY AWAY FROM THE TRACKS. THUS REMOTE CONTROL EQUIPMENT IS NOT A SAFE WAY TO. MOVE FREIGHT CARS.A MANNED HELPER. CONSIST IS BETER THAN THIS DANGEROUS EQUIPMENT.
@@terrywallace1327 ok so there are so many CSX derailment in Georgia, can yo please name the date of the one in question? I'd love to read about that
I like it old locomotive than new technology is shit
What fps is that bud? 15fps? 🤣
No why?
The issue of the Sand Patch stop is a poor joke. The idea of the sin shouldn't be to irritate to this degree. It's stupid.
This is why I wouldn’t want to be a train driver in real life because of how slow they go stowaway the freight trains not so much on passenger trains
I loved work freight over passenger lol. They both have there pros and cons though.
Oh maan please, either reduce some settinx or buy a faster cpu.. this game is very cpu demanding you know and you can see that too from your gameplay experience.. i have phenom 960T 4cores up to 4Ghz and maaan it IS struggling so i go for FX 6300, gonna up him to like 4.5Ghz..
Bro this isn’t PC
Lol I wish I had a PC.