You are a genius, I looked for how to disassemble this without resorting to a hammer and I couldn't find anything until I found your video tutorial, I deeply appreciate it, thank you very much, thank you very much
Thank you so much I have searched a lot on UA-cam on how to open it but I didn't find anyone that made a video about it except you although it's not the same model as mine, but still braun as well and it has the same way to open. so thank you so much
I managed to get this opened as well. The plastic housing cracked slightly while I pushed the blade in the seam - in a couple of spots. The fault was identical to this video's: The switch spring was not soldered properly and had broken loose. I had to heat the spring up a long time before it accepted good contact with the molten solder. It seems to work now again.
Same problem , didnt have paper knife ,so used filet knife , after cuting myself twice , decide to use fire , so I melted all around and get it Open , clean a bit, fuse some metal and miracle happen it started working with no problems , so I set all parts like they was before and fuse them
Thanks a lot, great instructions, though video was bad quality. Mine took a lot more than 2 mins to break the glue around the perimeter (more like 20-30 mins).
Son deshechables? No están diseñadas para ser reparadas, cuando tal vez se trate solo de falso contacto o desgaste de las brochas. "Ha de tener un alambrito suelto" dicen mis clientes. Pero llegar a ese alambrito suelto casi la destruyes. La construyen monopolios voraces que no permiten que nosotros los técnicos podamos sobrevivir con nuestro trabajo.
It was much more difficult to take apart than you made it seem, but I did it! Not yet sure if I can fix it, though. Still haven't identified the problem.
Diane Harrell You made me laugh….you can tell by looking at his that it takes a little doin..like a lot off doin,probably the hardest part of it…I'd do it too, I still have mine from a while ago & their work horses + I'll try fixing anything past the point of making any kind of sense.
I have the same ditto copy…problem with is that its cement resistor is burntout / exploded / broken , so cant figure out its rating….( was something like 35W5RJ… as i remembered while fixing same push button connection).. i am stuck figuring out its cement resistor rating. Its Braun 120VAC- 200 watt . Please help
Hi every body ,I have a handblender elektrolux model ESTM6600 ,I couldn't find a video clip in UA-cam to se how I can open it,I know how to repair the electrical fault which happen to it but my problem is ,I can not open the body of this handblender,is any body can give.me.some advice, unfortunately i couldn't find schematics manuals. Thanks for reading my words.
The top cover is extremely difficult to lift because of those plastic notches. Basically it's not made to be opened (a 'one way' design). Risk of breaking the plastic and damaging the gear inside. Try first ungluing the bottom blue ring if you can, but all in all this unit is not designed to be opened for repairs. Sad choice by Braun
Yeah it pisses me off when someone does a demo with only his left hand. 8 minutes to show us how to open a blender! With both hands it would've taken only 3!
If anyone has the same blender, the first thing to remove is the blue ring then maybe use a heat gun to weaken the glue around the rim before prying off the motor housing/ casing. Do not start with the top where the cable comes into the blender because you will end up breaking very useful couplers. That is not how disassembly of this unit was meant to be at all! Even using a box cutter blade is a very risky and dangerous undertaking: use a flat screw driver to gently pry the housing apart.
So sick of all this built-in obsolesce... make it as hard as possible to repair so the customer has to buy a new one. Really sucks and is horrible for our landfills. People need to start demanding reasonably repairable products!
Awful!!! Bamix Of Switzerland is assembled with screws and very well designed, compared to this!And not so much more expensive. Long lasting if treated correctly.You buy one, and it is the first and the last one 😋😋.Think about it.
You are a genius, I looked for how to disassemble this without resorting to a hammer and I couldn't find anything until I found your video tutorial, I deeply appreciate it, thank you very much, thank you very much
You are welcome!
Thank you guy! I already wanted to spray it :) You helped me very much!
Thank you so much I have searched a lot on UA-cam on how to open it but I didn't find anyone that made a video about it except you although it's not the same model as mine, but still braun as well and it has the same way to open. so thank you so much
Glad it helped!. Thank you!
@@TheWonderworlds 🌹
Thank you very much.
Thanks for help.
Thank you for your effort
I managed to get this opened as well. The plastic housing cracked slightly while I pushed the blade in the seam - in a couple of spots. The fault was identical to this video's: The switch spring was not soldered properly and had broken loose. I had to heat the spring up a long time before it accepted good contact with the molten solder. It seems to work now again.
ó
Thanks for the comment! if the switch ever breaks, hopefully I'll remember!😆
thank for this info. How can I open an old blender 4 169?
Thanks for ur video, how to remove the hand blender blade.
Do you think a heat gun might soften the adhesive or not really ?
Very useful video
Is there a fuse that can be replaced? Braun 5550 mr multiquick
Same problem , didnt have paper knife ,so used filet knife , after cuting myself twice , decide to use fire , so I melted all around and get it Open , clean a bit, fuse some metal and miracle happen it started working with no problems , so I set all parts like they was before and fuse them
thank you for that
the older models had two screws under small caps to access the top....
Thanks
and how did y6ou open that back cover at beginning?
What if you burned out the motor? Can it be fixed?
Esta trabajando con un solo mano
Thanks a lot, great instructions, though video was bad quality. Mine took a lot more than 2 mins to break the glue around the perimeter (more like 20-30 mins).
Son deshechables? No están diseñadas para ser reparadas, cuando tal vez se trate solo de falso contacto o desgaste de las brochas. "Ha de tener un alambrito suelto" dicen mis clientes. Pero llegar a ese alambrito suelto casi la destruyes. La construyen monopolios voraces que no permiten que nosotros los técnicos podamos sobrevivir con nuestro trabajo.
Did you repair it?
It was much more difficult to take apart than you made it seem, but I did it! Not yet sure if I can fix it, though. Still haven't identified the problem.
Diane Harrell You made me laugh….you can tell by looking at his that it takes a little doin..like a lot off doin,probably the hardest part of it…I'd do it too, I still have mine from a while ago & their work horses + I'll try fixing anything past the point of making any kind of sense.
IT WILL BE WITH ONE HAND... WASTE OF BLOODY TIME 🐐
I have the same ditto copy…problem with is that its cement resistor is burntout / exploded / broken , so cant figure out its rating….( was something like 35W5RJ… as i remembered while fixing same push button connection).. i am stuck figuring out its cement resistor rating.
Its Braun 120VAC- 200 watt . Please help
2.2 Oh 4 Watt
Hi every body ,I have a handblender elektrolux model ESTM6600 ,I couldn't find a video clip in UA-cam to se how I can open it,I know how to repair the electrical fault which happen to it but my problem is ,I can not open the body of this handblender,is any body can give.me.some advice, unfortunately i couldn't find schematics manuals. Thanks for reading my words.
The top cover is extremely difficult to lift because of those plastic notches. Basically it's not made to be opened (a 'one way' design). Risk of breaking the plastic and damaging the gear inside. Try first ungluing the bottom blue ring if you can, but all in all this unit is not designed to be opened for repairs. Sad choice by Braun
heb met deze informatie onze staafmixer weer aan de praat gekregen. contactpin van switch was losgelaten.
should have put camera on stand and used both hands
Yeah it pisses me off when someone does a demo with only his left hand. 8 minutes to show us how to open a blender! With both hands it would've taken only 3!
Thanks. More glue is being used to hold things together. Damm
agreed, its clean way to do it and less of additional screws etc.
My blender stopped suddenly
Thanks just Helu me
Aing mah teu nyaho😂
If anyone has the same blender, the first thing to remove is the blue ring then maybe use a heat gun to weaken the glue around the rim before prying off the motor housing/ casing.
Do not start with the top where the cable comes into the blender because you will end up breaking very useful couplers. That is not how disassembly of this unit was meant to be at all!
Even using a box cutter blade is a very risky and dangerous undertaking: use a flat screw driver to gently pry the housing apart.
I lost its attachments..where to shop for them
You gotta take the top off to remove the motor.
Sir, How to open Braun MQ500 blender?
So sick of all this built-in obsolesce... make it as hard as possible to repair so the customer has to buy a new one. Really sucks and is horrible for our landfills. People need to start demanding reasonably repairable products!
Awful!!! Bamix Of Switzerland is assembled with screws and very well designed, compared to this!And not so much more expensive. Long lasting if treated correctly.You buy one, and it is the first and the last one 😋😋.Think about it.
Your email address
Need guidance how to open braun blender to change carbon
A waste of time - throw it in the bin and buy a new one,
POOR VIDEO. YOU DIDN'T SHOW HOW TO OPEN THIS ,,CAP"
This product sucks..!
Thanks