Getting Wood/Lumber Dead Flat with a Hand Plane
Вставка
- Опубліковано 14 лис 2020
- Support What We Do at The Katz-Moses Store lddy.no/stih
On today’s woodworking skill builder I show you how to flatten a board with a hand plane. I also show you how to make VERY cheap and easy winding sticks. Flattening by hand is a right of passage for woodworkers and great exercise hahaha. Whether your lumber is wider than your planer, you have a giant slab, a work bench or you just like to use hand tools, this is a must have ability. Let me know what you’d like to see next. Thanks for watching! Please like, comment and subscribe. Cheers!
----
Support What We Do at The Katz-Moses Store lddy.no/stih
Sharpening Video you should watch • Scary Sharp - The Chea...
How To Setup Your Handplane (super helpful in this process) • How to Set Up a Hand P...
----
Buy the Katz-Moses Magnetic Dovetail Jig: lddy.no/stiz
Taytools is my favorite woodworking tool source: lddy.no/e90a
I have Walnut Slabs for sale: lddy.no/stj0
Buy the Katz-Moses Stop Block: lddy.no/stiz
BitsBits is the BEST place to buy router bits: bit.ly/BitsBits USE CODE JKATZMOSES15 for 15% off
Total Boat Epoxy: bit.ly/2I3Q8m4 10% Discount code JKATZMO
----
Essential Woodworking Skills Playlist: • Essential Woodworking ...
----
Woodworking Routers Video Playlist: • DIY Router Table Build...
----
Woodworking Joint of the Week Playlist: • Woodworking Joint of t...
----
Woodworking in SLOW MOTION Playlist:
• Slow Motion Woodworkin...
----
Tool Tune Up Thursday Playlist: • Tool Tune Up Thursday
----
Check me out on social media:
jkatzmoses
www.Facebook.com/katzmoseswoodworking
patreon.com/katzmoseswoodworking
/ katzmoseswoodworkingshop
----
Tools I love:
The Katz-Moses Woodworking Apron: lddy.no/stir
My favorite Dozuki dovetail saw: lddy.no/stit
My favorite Ryoba saw: lddy.no/stiv
Marking Gauge: amzn.to/2nlXLuQ
Marking Knife: amzn.to/2nm39Ok
NEW Suizan Flush Trim Saw: lddy.no/stix
Stanley Sweetheart Chisels: amzn.to/2mVMTkF
Knew Concepts Fret Saw: amzn.to/2FUDbYZ
Dewalt Planer Package: amzn.to/2thEf6O
Forrest 10” Combo Blade: amzn.to/2Fdaee3
Festool Tape Measure: amzn.to/2oS3cjD
Starrett 6” Combination Square: amzn.to/2oP3dVw
Woodstock 3 in 1 Shoulder Plane: amzn.to/2FgAS1A
Stanley Low Angle Jack Plane: amzn.to/2oV4I4O
Dewaxed Shellac Flakes: amzn.to/2FeqqYh
Abalone Inlay :amzn.to/2rjMTxe
Abalone Inlay Alternate: goo.gl/DHonFy
5 Minute Epoxy: amzn.to/2FijsSa
Triton 3 ¼ hp Router (with built in lift and edge guide incl): amzn.to/2LBw3Go
Kreg Router Plate: amzn.to/2A7oVNC
Triton Bushing Set: amzn.to/2A7pSpa
Bosch 1 HP Colt Router Set With Fixed and Plunge Base: amzn.to/2mHP1wY
Bosch Edge Guide: amzn.to/2uRRKs2
Bosch Bushings Set: amzn.to/2JUNRYb
Centering Cone: amzn.to/2OjgOAf
MY CNC MACHINES (I highly recommend both)
Bescutter Laser’s Website: bit.ly/bescutter
Avid CNCs of all shapes and sizes: bit.ly/3cdKdqA
----
Camera Gear:
Lumix GH5-s and main lens: amzn.to/2J49F7m
30mm Macro Lens: amzn.to/2GJXtTT
15mm Lens: amzn.to/2NafUox
50mm Lens I use for product shots: amzn.to/2mehs5y
Microphone: amzn.to/2IGjKIa
Lav Microphone: amzn.to/2Nb8SzY
Gimbal: amzn.to/2s9ZV0F
2nd CAMERA Canon 70d: amzn.to/2FiCEDq
Tripod: amzn.to/2HasNvK
Slider: amzn.to/2oNucSd
24MM Wide Angle/Macro Lens: amzn.to/2oSzzjh
50MM f/1.8 for those tight shots: amzn.to/2tpAoVm
10-18mm Lens for the wide shots: amzn.to/2FZrhNM
Musicbed SyncID:
MB016ZMTQEWO7ON - Навчання та стиль
*Support What We Do at The Katz-Moses Store* bit.ly/KMWstore20
*Sharpening Video you should watch* ua-cam.com/video/eom0qu5YO94/v-deo.html
*How To Setup Your Hand Plane (super helpful in this process)* ua-cam.com/video/QYiALzXkOWk/v-deo.html
🙏🤝🇮🇩🇮🇩
got my new jkm apron delivered here to ireland last month, bloody mrs took it and said thats for xmas u cant have it til then ..grrr lol im sure it will be worth the wait mr Katz! :)
keep up the great vids and please not such a big gap between them :)
the author does like to from scratch, shaping and trimming wood from large blocks into fine finished products. ua-cam.com/users/postUgkxD-QRFQz730FJEh4f9BYSf-nkIMIC9hL_ as another reviewer mentioned, most projects require a lot of high-dollar equipment that most of us dont have the room or budget for. But, knowing how to do these things, even if we wont be able to practice the full stack project, is still great.
We recently lumbered a 36" maple, a 36" white ash, and a 32" pecan. After drying, we tried planing with a Rigid (Home Depot) 13" planer with 2 HSS knives ua-cam.com/users/postUgkxIzvvTi3_Qc8JnVdYYRJCvuoDC4QjTzeL . This job was clearly too much for that machine. The pecan was particularly difficult, due to heavy mineral deposits, and a sharp pair of HSS knives would be consumed by a mere 3 boards. We were also having lots of problems from chip bruising, due to poor dust collection. The shavings came off like straw and jammed in the 4" hose.We bought the DW735 simply to be able to run carbide blades, which worked brilliantly for the pecan. However, we found it to be a much, MUCH nicer machine. It was far more rigid than the "Rigid" planer, and far more accurate as well. But what I liked most about it was the dust feed. This machine has its own blower, which shreds the "straw" like shavings as they come off the cutting head and helps boost the shavings into the dust collection system. No more clogs! It's also nicely sealed so that the internals stay quite clean. This is just a well tempered machine that's a delight to use. It literally cut the labor in half. Just another example of getting what you pay for.
I watched videos like these and spent almost a week (an hour at a time) and completely planed a table top. Wow, the results were so worth it and made me feel so proud
Just bought a $40 electric hand planer to level some joists and watching this thought, "wow, that's an absurd amount of work for a single side of a single board. Why when you could spend that time doing a gig job to buy a used jointer?"
Thanks for pre-answering my question.
This video alone makes me completely comfortable with what I paid for my power planer. Pretty sure I'd die if I tried to flatten a bench by hand. Nice vid, JKM!
Hahaha I was pretty sore the next day.
I am with Drew on this one.
Just get flat wood from your neighbor and don't worry about it.
I use a homemade flattening jig with my cheap router. I mean... It's close enough for what I need. Only downside is the size of the jig limits the size of the boards I can flatten and thickness
Super helpful content! I’m a novice and heard of winding sticks before but never knew the application. Definitely gonna try this out when trying to level out the top of one of my desks I’m working on. Thanks for keeping it short, sweet, and to the point.
I am glad to hear that you have found this book to be very informative and helpful for your woodworking project ua-cam.com/users/postUgkxbnOKZBE4evMO5V2vroHeCjq6d_MV6wJO It sounds like you are well prepared and confident to build furniture for your house. I commend you and your friend for your enthusiasm and willingness to learn new things from this book. I hope you enjoy your woodworking journey and create some beautiful pieces.
Welcome back and thanks for the tips. All those guys you referenced are great sources for hand-tool info. Glad to see you incorporate it a little bit into your info. Keep up the great videos!
When flattening longer boards, it's best to check for twist with respect to the middle of the board. Keep one winding stick in the middle and place the other at either end of the board. One corner may be higher than the other.
Thank you, Jonathan. Appreciate you sharing your knowledge/experience.
I'm just getting started trying to flatten/dress my own rough timber by hand. It's hard work but super rewarding and I'm sure the neighbours appreciate how much quieter it is :P thanks for the video!
Awesome the winding sticks!
When flattening larger boards (the ones that are too big for my jointer and/or when I don't want to mess with a planer sled), most of my passes are traversing cuts. Maybe 90%. I can take a much more aggressive cut with my scrub and jack planes in this direction.
Also, I start on the concave side. I've found that while doing traversing passes this keeps the plane from rocking on center and produces much more predictable cuts and results. And if I'm planning to run the board through the thickness planer I finish with just a few longitudinal passed with a #7 or #8 jointer plane just to knock down the high spots.
For table tops or large glue-ups I follow the above but work to get a full length cuts with my jointer planes in all directions before finishing with a smoothing plane and scrappers.
Once you have a sound strategy in play, flattening large boards and surfaces with hand planes can be extremely satisfying.
- Cheers!
I’ve been using angle iron with the “corner” of one piece colored a contrasting color, then I lay both pieces so the “corner” is facing up. Seems to work, but this is the perfect project for those extra pieces of ply that seem to pile up. Thank you.
Great video Jonathan... I have learned so much from you over the years... I even have a couple of your hand planes. I have to admit that I built myself a pair of Paul Seller's winding sticks about a year ago. I knew then that I didn't NEED anything that fancy, but I looked at it as an exercise in precision. The workmanship he put into his set really convinced me to take it up a notch. I still have them, I use them all the time, and they are still dead flat. I made mine out of Mahogony, Ebony and Hard Maple. Every once in a while, I give them a fresh coat of wax and buff them to a nice sheen... just to keep them looking nice.
This is great. Some solid principles. Now I know what I need to make and practice ahead of my next project. Thank you!
Thanks for this. I have a small workbench I’m making that is my first hand planing project. I did plane it originally but I did not do it even. As no this helped out getting it straight. Appreciate the videos!
Great explanation Jonathan.I never asked myself the question how to set the plane on the workbench,cause it answered it by coincidence,when left it laying on the side while I wanted to wipe the shavings of the surface and touched the blade by passing with my nuckle....I was damned happy that I was able to get a blade that sharp,but it was a red mess,and a clean cut in the wrong material.Thanks for your content,I learned a lot since I watch the videos.
Thanks again, Jonathan! Great info, great video quality. Good to see you again. We worry.... so it’s good to see you posting videos again. ;)
Thanks for every think you show us. Just getting started in wood working.Making 3 kind wood end grane cutting board.
I was inspired by this, I fixed a chair leg with duck tape.
😂
I just left the tape on mine! Been using blue tape winding sticks for awhile now, and it’s great! Thanks!
Awesome thanks for posting. Glad to
See you out a video up today. Love your videos 😊👊🏻
There’s something special about taking a rough piece of lumber and turning it into a glass smooth piece of furniture or whatever. I love hand planing, the sound, the feel of the blade cutting the wood. It really is relaxing
I agree. Everyone acts like it’s physical torture but I find it to be a relaxing pleasurable experience.
@@displaychicken me as well…. I could literally plane for hours with no real objective in sight.. just planing to make chips
Welcome back! Hey!! Love the apron! And 317 other fellow craftsman did too!! And the Japanese saw work amazing! Dove jig is in my next list!!
I end up with whining sticks... I’m lousy with hand tools so my planing becomes complaining
Foul! (Reaching)
😂
Well done
Yessir
Glad to see you back, and has been mentioned above I'm really happy to see the public recognition of the other guys -- I rely on pretty much the half dozen you mentioned immensely. Eternal thanks to you all!
This vid is so great. I recently made my UA-cam-content-creators inspired mini-workbench dead straight using only hand planes (whilst wearing my Katz-Moses apron). I’m so happy with it 😃
Nice!
I have an okay-ish power planer but no power jointer, so when I want a true face on a board before going into the planer I have to do it all with handplanes, and I agree with you that it is a real workout!
I know you probably don't prep like this often, but for anyone who does, I've found that having a lower workbench height, or even a planing support down a little lower than your normal bench height (I think Shannon Rogers of the Renaissance woodworking talks about this option) can make a big difference in how much effort this takes. When I plane up high my arms and shoulders are doing all the work and get tired, a little lower then my legs are doing most of the work.
Great video, love your content Mr. Katz-Moses, and I just ordered a dovetail marker and a shop apron from your store, take care of yourself sir!
I did start my flattening "career" with a jack plane. Honestly, it wasn't all that bad, just time consuming.
Once I got a bandsaw, I started using my veneer sled to slice off the convex. I cut the concave out of the other side running the newly "flat-enough" side against the bandsaw fence. This saves a TON of time.
I still finish the flattening with hand planes.
Working with hand tools is truly a labor of love and dedication
As always excellent tips and tricks! Keep up the excellent job.
And thanks for the best apron, the build quality great and the layout is superb
Really appreciate it my friend!
@12:49 Great to have you back!
Thanks for the info Jonathan! 😃👍🏻👊🏻
Being new to woodworking I thought it would be fun to hand plane a piece of oak 1/8” convex. What fun! I was so sore for days.
Great to see you back, Jonathan and I’m looking forward to watching you build that marking gauge 👍
As a side note, I have some Veritas winding sticks, which are great value for money and didn’t break the bank. I’d definitely recommend them to those who don’t have any machines to produce plywood ones on a table saw, like myself. (I shudder at the thought of using my planes on plywood 😁)
I use my metal-bodies planes on plywood edges without too much difficulty, but it does dull the cutter a lot faster and require more sharpening. Also I usually skew the plane on a plywood edge to try to spread the wear out over a wider area on the blade. It can be a little odd to have razor-sharp edges and a dull center. :)
I don't use my wood-bodied planes on plywood edges because of concerns with "hollowing" a strip along the sole of the plane, since plywood is so abrasive.
Beautiful explanation and demonstration.
What a great video! Thanks for the help.
thank you Katz . so i start with a 4/4 and wind up with a 1/2 " board lol i can see it now
You did a great job and very helpful, thanks for sharing.
You haven't lived until you hand plane all of your rough stock for a project. Puts hair on your chest. I've lived. And now I own a power planer.
Shit, go find the video of Wood By Wright doing his new hardwood floor completely by hand! My back still hurts from watching
You haven't lived until you've reached your deathbed hand planing all your rough stock for projects without ever having used a power planer in your entire life.
I'm not worthy
Hi handsomes we have 3 comments here
This is all very plane communication.
Your videos have helped me some much. Thanks man!
I was fortunate enough when I started out to buy all the machines I needed, sometimes I wish it would have been the opposite as I feel like I would be a better woodworker, better understanding ya know... studying hand planes hence, why I'm watching this in hopes of getting better, more knowledge equals better projects...don't know bout anyone else but I appreciate you John..thanks...
Good video!! For my winding stick I am using 2 levelers 60 cm each, good quality ones ( made out of Aluminum alloy).
That's a good video, thanks a lot namesake! :) The trick of waxing my plane is excellent, and I wish I had heard it sooner. Bet it'll make planing noticeably smoother!
Great video! I am just getting back into woodworking and am lacking my ex-father-inlaws shop of plenty. This is exactly the brush up I was looking for. Subbed!
Helpful video; thanks for sharing your insights. Best wishes.
As always, great info!
Fantastic, Jonathan! Thanks a lot! 😃
Some fantastic tips there!!!
Stay safe there with your family! 🖖😊
Great to see you again JK-M good video!!!
Another great video, thanks for the tips!
Content is great. In additions, the picture is a pleasure to see, the colors, the lighting, the background. Bravo!
I really love this
I am using my Katz Moses apron every day I am in the shop! Great woodworking apron!
Yes!
Good video, veery informative. Thanks for posting.
Thank you for the great educational video!
Really I enjoy watching your videos 😍
Welcome back brother... have missed ya!
Great work. Great exercise too!
I was sore the next day. Been a minute.
as you say, i'm starting out without a router or planer and have some boards to surface. just what i needed, thanks for upload
@JK an easy way to remember... skateboards are concave. The boards are formed with a dish shape so your feet stay locked in better. Some boards have more than. others but there haven't been any flat boards I've seen since the late 70's.
Nice,, super inspiratif
I use my two carpenter squares as winding sticks. A bit of tape on the edges if the light isn't good. And I can shoot a light underneath. Not the absolute best, perhaps, but it get's the job done quickly.
I also place my planes blade down. The times I didn't, I reached for something and lost a lot of knuckle skin in the process...
I used an 18 inch bubble level to check & recheck as material is removed. Took me a while, but I used various grits of sand paper, the boards were closer to square/true than the slab you started with though. I leveled & planed a 3 piece guitar body blank from a couple of 2x6's & a 2x4. I will move on gluing them edge to edge & I got the board to be 90 degrees too. Next time I'm just going to pay the man for a slab that has been planed, glued & squared with a planer. This is a "one of" project. Can't find anyone that wants to square up the lumber. It's Loblolly Pine that was been kiln dried to be at least dimensionally stable. I also have to reverse draft the body shape & trace that out to get close & then shape it smooth for finishing. Then there is the routing. The guitar body is the Valco Airline shape, nobody has a pdf of the body dimensions for a template or blueprint, so I'm getting it online image close for the guitar neck. My first cut at this, I wasted too much time on this already. Figuring it out was more than I bargained for. But now that I'm at a point where I feel comfortable to move to the next phase, I find this video with the right UA-cam search.
Keep it up Johnathan 👍
Thanks bud! - Jonathan
Love this great video
Yaa nice video
Power stropping...I like it.
you're one of the only woodworkers that get me to laugh. I laugh and learn at the same time
Awesome video
Oh boy...i got a 13ft red oak plank I need to plane. That should be fun!
Nice good !! 🔥🔥
Good video chief
I'm in the middle of doing a 6'x3' butcher block and my thickness planer broke halfway through so now I'm getting my big boy pants on a learning to hand plane finally lol
First time seeing one of your videos. Dude you sound just like jimmy Kinmel. You even look a bit like him. Nice job btw. Thanks for the info
Yup it’s a lot of work. And can be quite frustrating. I’m a perfectionist so I have a piece of marble that I check the faces of the wood on as I’m flattening and if there’s any movement on it I’m not content with it.
I'm now hand planing a few small laminated boards. Really regretting not properly squaring the corners first, but the wood wasn't even all that straight to begin with.
The reason I didn't square it first was because I need the widths of the boards to line up perfectly.
Is that Danny DeVito helping you sight down the winding sticks at 7:15??
Great video as always!
Is that Danny Devito sitting in the background looking encouraging lol
Shout out for the Rustoleum Ultra Cover spray paint. I’ve used that stuff for years because it’s the only one I’ve found that doesn’t take a million coats 🤣
SO GOOD!
I totally appreciate the artistry and love of planing. That is not me. I want instant results (sanding I can deal with) without going back and forth until the wood is only 1/4 thick and still twisted. If good planes were not so expensive I might try it out but i cannot risk that and say I will never use a plane again.
I live in a house that's been built around 300+ years ago (Europe). They used stone and wood. And one must admire their work but they probably had also way more time to create something!
I don't have planer but I plan to build planing jig for my router. I can't spend this time flattening one board :D
At least you were consistently incorrect haha. I actually enjoyed the text on screen. that was funny, and I think I won't be making that error myself after learning from yours.
"planes are ground straight and square, if you get a good one"..
I hear ya brother..
I have a #4 which, yesterday I discovered, was anything but..
All 4 corners were high, like, when I put a straight edge (a brand new 12" steel ruler) I could get a piece of paper under it at the blade slot..!
It also had a 4" long by 1.5" low spot just left of centre, behind the blade slot, extending most of the way to the tail end..
Argh!!
Kind of explains why previously planed (jointed) boards never lined up exactly right..
Anywho.. how to fix?
So I clamped a 2-foot long slab of 1/2" steel plate to my bench, made sure it was flat, and broke out the wet and dry..
Started at 240 grit, figuring "it'll only take a minute to sort this, surely"..
Hah!
I quickly went down to 180.. then after an hour, down to 120.. an hour after that, now thoroughly aggravated, I gulped, and reached for the brutally efficient 80 grit..
Another hour after that, and the low spot was gone, and I began to work my way back up the grits to 400, then a final clean and a coat of boiled linseed oil..
This all took the better part of 5 and half hours.. something which the maker of this plane should have done in 3 minutes on a mill..
But now I have a - flat - plane.
Please turn on auto captions! Thanks for making those videos!
Good call.
@@katzmosestools Thanks!
@@thevtest i think you just watched it too early. Takes a bit for the UA-cam AI to get them up
I’ve been working with 2x4s to make some dovetailed monitor stands. I resaw them and plane them down to about 1/2” thickness over the course of 3 days. After final thicknessing, they still move like crazy which is very annoying. Is this because the wood is still too wet? I got lucky and found some quarter sawn kiln dried 2x4s but they still move.
lol.. give me two options , I'll f'em up forever. This one is easy tho boss, caves are holes in the ground , you got it.
"The less friction the better - keep your minds out of the gutter"... more friction is better, but there can be too much.
What about using Aluminum Angle Bar or Tube as winding sticks?
Thanks for this nice video again. I am only wandering, what are you using the clamp the board?
I know there are traditionalists that value this type of experience. This is nice to know... However, at my age, paying 500-600 dollars for a great planer setup will extend my life greatly... and considerably cut down the time to when I can use the board. Is it just me, or did you take about a half inch off the top of that board... and you still need to do the other side??! On a planer/shaper, you can make a sled to attach the board to, (using hot glue firmly keeps the board in place) then after two passes, only the distance to the bottom of the troughs is taken off, maybe an eight inch or less in most cases, then just flip the board send it threw one more time and bang! You're level both sides!
PS- love your videos, and your info, not a bad one here, and there are several situations this is great to understand and know- so keep going!
Are these good for planing the edges of 2x4’s ? I want to build tables but need a way to make boards with a nice square edge
Very nice video. But when I try to flatten a board, somehow I keep ending up with low corners. Is that on how I hold my plane? Can it be my vise? My planes are all flat and straight. The blade is also parallel to the soul. I just can't seem to find a solution to not end up with low corners
THE REPEATED *CONCAVE *CONVEX MISTAKES.. LOL!
Well after this I know k ow I really need to buy a planer.
Puzsér úr, nem is tudtam, hogy ön már fával is dolgozik
I'm ringing in the new watching this video despite the fact that I don't have any money to get into woodworking.
I’ve never had trouble just using a single straightedge for flattening boards and whenever I see someone using winding sticks I just don’t see what great advantage they offer.
If all four edges are flat and the diagonals are flat, all easily measured with a straightedge, then the board is flat. Simple as that.
So I was wondering about this when watching the video. Can I just take a combination square to each corner and if there is no light showing when I put the square up against one side, it means it's flat?
Nicoya: I have a 48" Empire straightedge from HD. It's 1/64" out in the middle. I have high quality angle iron from McMaster and it's not. Is your straightedge long enough? And is it actually straight? Not to say I could make anything better out of wood, but I've always questioned the practice of nonmetallic measurement references. And even metal isn't always of good quality.
@@mkplante It's easy to verify that a reference surface is flat (or make it flat) using the "3-plate method", in this case applied to a straightedge. If you've got three straightedges and there's no light between any pair of them, then all three are flat.
When you looked at them with your camera you should have used a higher F stop to increase the depth of field.
I like your apron.
Tha ks bud!! For sale on my website.
I too have watched enough Paul Sellers and Matt Estlea that I now say "leee-ver" 😂