I turned on the device and understood its principle of operation so, if I understand correctly, this thermostat is not suitable for replacing a pipe thermostat for a water circulation system. Because the thermostat's switching system is +-10 degrees Celsius from the set temperature point. Am I right? And don't even try to set it in my heating system!?
Hello friend I bought a DTC2201 device. For a water space stove system. I would like to use it to control the circulation pump. My question is how to connect the pump to which number of connectors? My second question is how to program the pump to turn on at a temperature of 35 Celsius, and then turn it off when the temperature drops below 35 Celsius. I await your respectful answer.
Hello, I am not sure what kind of pump you have but I mention them as load. assuming we have two wires. Just cut one of the wire as shown in the video (I just watched the video to make sure what I am talking about). for the programming I believe I have explained all the features. I can't watch it fully . please watch and see if it can do it. if you don't see it in the video, then it can't do it.
Para cada video tengo una página de recursos con toda la información relevante. El enlace está debajo del video en la descripción. Pero aquí para ti robojax.com/L/?id=122
Thank you for the video....I need 12-72 V DC models, but I can't find the product code. Can you tell me where I can find DC models, with and without WIFI ??? Another question ... does the WIFI model need internet connection or it also works only with WIFI network (LAN) even without internet ??? Thanks for your help
I searched and can't find it. there is another product that I did the review and it has been viewed 5 times more than this so check it out ua-cam.com/video/TUbnsNfK8Z4/v-deo.html as it has DC and AC
Longitud de la línea del sensor: 100 cm . Voy a aumentarlo a 30 mts.(3000 cm) ya veremos si funciona correctamente y si tenemos alguna perdida. usaré cable apantallado para minimizarlas al máximo.
pruebe con 1m y mida la misma temperatura y conecte los 30m y mida. Compare y si ve una discrepancia, compénsela. Creo que este módulo tiene esa característica para sumar o restar temperatura. Si es así, seguro que lo he explicado. Buena suerte.
Hello Ahmed, thanks for this video. I have the 2201 Wifi version. It measures 1 Degree C too high , so I wanted to use F4 Cal function. When I set F4 to -1.0 Degree it should be reading OK but the Display still reads the same Value . (1 Deg C too high ). Am I doing something wrong ? Thanks, Erik
@@robojax Hi , thanks for your reply. Do you still have yours? Can you please try the F4 calibation and see if the measured value on the display changes? Thanks
Actually just found out they are stainless steel so will eventually rust (plus I'd guess the grade quality of the steel will vary a lot) so think I will just dip mine in plasti-coat, which may affect the speed the sensor but I'd guess not to the extent it will be an issue for me.
3 роки тому
Hello friend, I could do a test below zero degrees, mine only reaches zero degrees, but the freezer is at -17
Thanks for a great vid. Following your diagram I got the unit to work.
Excellent instructions. Thank you mate :D
Happy to help
I turned on the device and understood its principle of operation
so, if I understand correctly, this thermostat is not suitable for replacing a pipe thermostat for a water circulation system.
Because the thermostat's switching system is +-10 degrees Celsius from the set temperature point. Am I right? And don't even try to set it in my heating system!?
Hello friend
I bought a DTC2201 device. For a water space stove system. I would like to use it to control the circulation pump. My question is how to connect the pump to which number of connectors?
My second question is how to program the pump to turn on at a temperature of 35 Celsius, and then turn it off when the temperature drops below 35 Celsius. I await your respectful answer.
Hello,
I am not sure what kind of pump you have but I mention them as load. assuming we have two wires. Just cut one of the wire as shown in the video (I just watched the video to make sure what I am talking about).
for the programming I believe I have explained all the features. I can't watch it fully . please watch and see if it can do it. if you don't see it in the video, then it can't do it.
for time controls I have more videos you may find something else if this module does not do it.
@@robojax The pump type is grundfos alpha 2. My English is bad, could you possibly show the video with Hungarian subtitles?
Thank you my friend!!!
the minimum my sensor gets is 0 I can't use this in the freezer, could you help me if you have any settings for negative temperatures?
Cual es la longitud máxima de la sonda de temperatura y que perdidas experimenta?
Para cada video tengo una página de recursos con toda la información relevante. El enlace está debajo del video en la descripción. Pero aquí para ti robojax.com/L/?id=122
Thank you for the video....I need 12-72 V DC models, but I can't find the product code. Can you tell me where I can find DC models, with and without WIFI ??? Another question ... does the WIFI model need internet connection or it also works only with WIFI network (LAN) even without internet ??? Thanks for your help
I searched and can't find it. there is another product that I did the review and it has been viewed 5 times more than this so check it out ua-cam.com/video/TUbnsNfK8Z4/v-deo.html as it has DC and AC
What about controller without delay for compressor ?
Longitud de la línea del sensor: 100 cm .
Voy a aumentarlo a 30 mts.(3000 cm) ya veremos si funciona correctamente y si tenemos alguna perdida.
usaré cable apantallado para minimizarlas al máximo.
pruebe con 1m y mida la misma temperatura y conecte los 30m y mida. Compare y si ve una discrepancia, compénsela. Creo que este módulo tiene esa característica para sumar o restar temperatura. Si es así, seguro que lo he explicado. Buena suerte.
Hello Ahmed, thanks for this video. I have the 2201 Wifi version. It measures 1 Degree C too high , so I wanted to use F4 Cal function. When I set F4 to -1.0 Degree it should be reading OK but the Display still reads the same Value . (1 Deg C too high ). Am I doing something wrong ? Thanks, Erik
it should work when you add or subtract. I am not sure what could be wrong.
@@robojax Hi , thanks for your reply. Do you still have yours? Can you please try the F4 calibation and see if the measured value on the display changes? Thanks
how do i ajast the controler to cooling on!!- start cooling at 25 c stop colling at 17 C
All the features has been explained. If you watch it, you should not have any questions
Dose anyone know what material the metal looking temp probe is made from, or knows if it is safe to use in saltwater without it corroding?
Actually just found out they are stainless steel so will eventually rust (plus I'd guess the grade quality of the steel will vary a lot) so think I will just dip mine in plasti-coat, which may affect the speed the sensor but I'd guess not to the extent it will be an issue for me.
Hello friend, I could do a test below zero degrees, mine only reaches zero degrees, but the freezer is at -17
it should work from -40 C. See the resources page robojax.com/L/?id=122 the link is in the description
Nic
thanks.
@@robojax wcm
Все понятно скажи по русски что куда
Я рад, что тебе понравилось. Спасибо.