Thanks buddy good info. In regards to ride height I noticed in your response it said adjust both. So does that mean if my front is off, so I adjust the opposite rear so how do you exactly compensate for ride height?
Thank you much. One of my front wheels is not lifting at the same time. I changed the shock fluid, but sort of having the same symptoms. Do you happen to know if its the shock bladder? I see one is rebounding slow. Also could it be that another issue not going straight is uneven wheel bearings?
Thank you for taking time watching my video/s. It could be bladder or the piston inside is worn out. Yes bearing can be issue aswell if one is not turning well. However there willl always be a torque steer if you are too quick on the throttle
I use droop screws to limit the droops. For the uneven suspension, I adjust shock preloads. but make sure to adjust both side to maintain ur ride height. Welcome and thanks checking my channel, hope you subscribed
@@rubenaycojr3494 kabayan sir? regardin blow overs depends on the road condition where you run ur rc on. Assuming you are using belted tires like GRP, you can wrap/reinforce it up with nylon wires(fishing wire) however that still doesn't fully bulletproof the tire specially if you use the wrong compound/softness/hardness base on your road condition and weather temperature. A stone can also messup your tire specially if your hitting beyond 100mph/160kph.
@@rubenaycojr3494 you MUST balance your tires too before running it, it will help a lot with the vibration. Blowovers though is very minimal with foam tires except if you hit a sharp stone or bump on ur road, however there are and cons of using foam. I would suggest get a foam and practice with it using low voltage setup such as 3S parallel or 4S parallel. Y parallel? so when you run 6s or 8s you dont have to adjust the alignment again since the weight will be same for 3s parallel and 3s series(6s) / 4s parallel or 4s series (8s)
Rubber will always grip better but also wear faster. Foam is good on most all surface but it can also spin out which will cause the rc to slide if the trottle control is bad. My personal preference since i live in Dubai where the road is always full of dust..i consider rubber if my car is light(sing packs setup like typhon) and foam if its heavy (2 packs)
Oh, I would love to run my fleet on that piece of road.! It looks gorgeous. The roads in the UK & Scotland are an absolute disgrace... It's like driving 100 years after the apocalypse.!! The potholes are bad enough to break my full size car, nevermind my RCs.
thanks for stopping by. Im using bsr foams and rubber (grp s5 on summer.. s3 on winter). Contact tires are okay tire but wont suggest if u are aiming for 130mph above. Would suggest you to get bsr or gone bananas instead ;)
@@haks_123 grps can handle 140 to 150 for lets say 4-6 runs after that its prone to exploading.. but some do expload on the first run its like playing russian roulette hehehe. However you can reinforce them to make them more durable a bit. I have video on that ;)
So I should use SHOE GOO flimsy Speed run rc car body ? ok how did you apply the shoe goo to make it nice and even ? Great Video I just SUBSCRIBED !!! THANKS from North Idaho, USA
Thank you appreciate. I used my fingers to apply the shoegoo this way i am able to apply it evenly and flat across the body specially on corners. i always do 3-4 layers of dry wall mesh tape and shoe goo
@@RCSpeedRunDubai thanks for the reply ! So 3-4 layers of Dry Wall Mesh tape & the. Shoe-Goo ... OR... 1-2 layers Mesh Tape + Shoe Goo & then add the extra 1-2 layers of more tape & Goo ? ...basically my Question is all the layers of Mesh tape at once or not ?
@@lindaafuqua6977 yes do 1-2 layer of mesh first with shoego, make it thin and let it dry. Then apply another layer of drywall tape and shoegoo this time apply more shoegoo and uuuuuurrrr good to go, light and flexible but durable :)
@@RCSpeedRunDubai nice matic subscribe ako sayo kabayan. maraming salamat sa tips mo sakit talaga sa ulo pag hindi straight yung takbo lalo na sa mga speed setup. mag lalagay na lang ako ng Gyro ... Ingat at Enjoy lang tayo sa Hobby natin. hehe
@@junjunlontae7097 proper suspension lang sir kumbaga imagine mo yung lamesa pag maiksi ung isang paa tabingi same concept :) ingat ka sa gyro kasi minsan kumokontra yun sa steering. Goodluck sir thanks sa sub
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
Thx dude!
Hopefully It helped u
Great Video! I enjoyed all of the suspension observations. Thank you
thanks Ben 🙂
Where can I get the range extender u got?
Hey bro, I got it from here before worldsfastestrc.com/rc-speed-run-essentials/
@@RCSpeedRunDubai thank you
Is a really great you share you knowledge . This will improve our sport and make up the level. Thank's
Thank you. Mostly base on my experience and not saying its right nor wrong. Happy to help anytime. hope you can check my IG aswell
the video I've been waiting for! you are great!
Nice video brother and thanks for sharing!👍😃 hope spring comes soon!!! Can't wait for it!!😆🏎🏎
Thanks, I can imagine how excited you are.
cool video bro..all good information..thanks for sharing mate
He deserves more likes/views...(transferable knowledge street cars)
Thank you sir just trying to help a bit :)
Thanks buddy good info. In regards to ride height I noticed in your response it said adjust both. So does that mean if my front is off, so I adjust the opposite rear so how do you exactly compensate for ride height?
Thank you, and yes you are correct, cross (X) adjustment
Good info buddy, subbed ! Thanks
thanks bud 🙂 i subbed back
Great tips buddy 💪🏻
Thank you much. One of my front wheels is not lifting at the same time. I changed the shock fluid, but sort of having the same symptoms. Do you happen to know if its the shock bladder? I see one is rebounding slow. Also could it be that another issue not going straight is uneven wheel bearings?
Thank you for taking time watching my video/s. It could be bladder or the piston inside is worn out. Yes bearing can be issue aswell if one is not turning well. However there willl always be a torque steer if you are too quick on the throttle
Good tips! Thank you!
thank you 🙂☝️
Hello.. what do you adjust to compensate for the uneven suspension? Droop screws? Thanks for your time..
I use droop screws to limit the droops. For the uneven suspension, I adjust shock preloads. but make sure to adjust both side to maintain ur ride height. Welcome and thanks checking my channel, hope you subscribed
Thanks for your reply. Any tips to prevent blow overs? Subbed!
@@rubenaycojr3494 kabayan sir? regardin blow overs depends on the road condition where you run ur rc on. Assuming you are using belted tires like GRP, you can wrap/reinforce it up with nylon wires(fishing wire) however that still doesn't fully bulletproof the tire specially if you use the wrong compound/softness/hardness base on your road condition and weather temperature. A stone can also messup your tire specially if your hitting beyond 100mph/160kph.
@@rubenaycojr3494 you MUST balance your tires too before running it, it will help a lot with the vibration. Blowovers though is very minimal with foam tires except if you hit a sharp stone or bump on ur road, however there are and cons of using foam. I would suggest get a foam and practice with it using low voltage setup such as 3S parallel or 4S parallel. Y parallel? so when you run 6s or 8s you dont have to adjust the alignment again since the weight will be same for 3s parallel and 3s series(6s) / 4s parallel or 4s series (8s)
@@RCSpeedRunDubai nice , i heard people using wire for grp can u show us and how to keep the wire on ?
nice tips bro
Nice tutorial!
Thank you, sharing what i observed
About the tires what the types is indicated for the types of roads?
Rubber will always grip better but also wear faster. Foam is good on most all surface but it can also spin out which will cause the rc to slide if the trottle control is bad. My personal preference since i live in Dubai where the road is always full of dust..i consider rubber if my car is light(sing packs setup like typhon) and foam if its heavy (2 packs)
@@RCSpeedRunDubai Nice. Thank's for the answer. And keep making those good videos with tips/tutorials about speed runs.
@@RBAERO thank you. Will try my best
Nice video no gyro needed
Nice video ty for the info! 😁👍🏻 I’m just learning so it’s all great info.
thank you brother happy to help you can DM me in IG in case
@@RCSpeedRunDubai thank you
Nice bro 👍
Hey brother, check your droop first thing…car on blocks with no tyres, and set it to just where the collar falls of the bottom of the shock:)
thanks brother, i subscribed back :)
Oh, I would love to run my fleet on that piece of road.!
It looks gorgeous.
The roads in the UK & Scotland are an absolute disgrace... It's like driving 100 years after the apocalypse.!!
The potholes are bad enough to break my full size car, nevermind my RCs.
Shiiit bro that sucks, yes the roads here are nice but I had to drive around 40-50km back and forth to reach the road with no / less cars
Good job
hey thanks for the video, which tyres are you using? and are contact rc 1/8 scale foam tyres good for high speed runs?
thanks for stopping by. Im using bsr foams and rubber (grp s5 on summer.. s3 on winter).
Contact tires are okay tire but wont suggest if u are aiming for 130mph above.
Would suggest you to get bsr or gone bananas instead ;)
@@RCSpeedRunDubai oh ok thx, and so with grp's how fast could u go with them?
@@haks_123 grps can handle 140 to 150 for lets say 4-6 runs after that its prone to exploading.. but some do expload on the first run its like playing russian roulette hehehe. However you can reinforce them to make them more durable a bit. I have video on that ;)
@@RCSpeedRunDubai oh god okay XDD, i currently just bought a limitless and it has stock hoons (whites) will it take 120 mph?
@@haks_123 i only reached 100 with hoons but some guys do have luck with it.. before u run.. rub some wd40 it will make it sticky for better traction
Took your advice and disabled my gyro then crashed the first run 😁. I set my gyro to half and it runs great.
hehehe sorry for the crash. gyro can help but once u go super fast and ur car is not properly weight distributed it can cause u more dollar hehe
What's about toe in / out in front wheels?
Oh yeah yeah thanks i forgot to mention. I only go with 0 on front. Ite more of a driver preference one. Thanks for mentioning 🙂👍
I keep the slightest toe out in the front and slight toe in for the rear. 0 camber in the front and slight camber in the rear.
All the best to u😂
So I should use SHOE GOO flimsy Speed run rc car body ? ok how did you apply the shoe goo to make it nice and even ? Great Video I just SUBSCRIBED !!! THANKS from North Idaho, USA
Thank you appreciate. I used my fingers to apply the shoegoo this way i am able to apply it evenly and flat across the body specially on corners. i always do 3-4 layers of dry wall mesh tape and shoe goo
@@RCSpeedRunDubai thanks for the reply ! So 3-4 layers of Dry Wall Mesh tape & the. Shoe-Goo ... OR... 1-2 layers Mesh Tape + Shoe Goo & then add the extra 1-2 layers of more tape & Goo ? ...basically my Question is all the layers of Mesh tape at once or not ?
@@lindaafuqua6977 yes do 1-2 layer of mesh first with shoego, make it thin and let it dry. Then apply another layer of drywall tape and shoegoo this time apply more shoegoo and uuuuuurrrr good to go, light and flexible but durable :)
No gyro needed, fellas spend time with your car.... this is a good start to set up Fellas... Run run run
Gyro
Pinoy?
yes kabayan
@@RCSpeedRunDubai nice matic subscribe ako sayo kabayan. maraming salamat sa tips mo sakit talaga sa ulo pag hindi straight yung takbo lalo na sa mga speed setup. mag lalagay na lang ako ng Gyro ... Ingat at Enjoy lang tayo sa Hobby natin. hehe
@@junjunlontae7097 salamat 🙂👍
@@junjunlontae7097 proper suspension lang sir kumbaga imagine mo yung lamesa pag maiksi ung isang paa tabingi same concept :) ingat ka sa gyro kasi minsan kumokontra yun sa steering. Goodluck sir thanks sa sub
@@RCSpeedRunDubai pero if ma set po ng tama yung gyro sir malaki po ba yung ma itulong?