サイコパスメイド娘フィギュアの作り方～ケサランパサラン・マーダちゃん～
Вставка
- Опубліковано 12 вер 2024
- ※あくまでケーキです。( ˘ω˘ )
使用したフィギュアはケサランパサラン M.ローラン氏原型 の「マーダちゃん」
キット開封後、組み立てから塗装までの製作工程を動画にまとめました。
台座を含めると30cmを超えるビッグサイズです！(=ﾟωﾟ)ﾉ
今回の見どころは腕、腹、脚部の透け塗装です！どの部位も異なった透け具合に仕上げております。脚部が一番薄いタイプですかね。(੭ु´･ω･`)੭ु⁾⁾
台座は３Dプリンターで出力してネームプレートもつけちゃいました。
それだけで高級感というか、グッと作品が締まりますね
途中に挟んだショッピングのお問い合わせは下記のURLからどうぞ( ^)o(^ )
#フィギュア #ガレージキット #ミニチュア #3dプリンター
ケセランパサランキット取り扱いストア
→www.delayedbra...
使用した３Dプリンター「Ender 5 S1」
→pergear.co.jp/...
現在amazonから購入すると、11%OFF クーポン
→amazon.co.jp/dp/B0BJV6K15R?ref=myi_title_dp
タイトル曲提供 KAIMU ZERO様
→ / @kaimuzero5921
投稿頻度が遅いためチャンネル登録でケツ叩きしてもらえると跳ねて喜びます(*'ω'*)
My Twitter→ / yonkeru_g11
へとへとですが何とか月一本の投稿ペースを続けれております(;´Д｀)
凄いですね😄
まだ留まることをせずに、進化を続けるんですね😆
感服です😄
瞳を描き込むまではお笑いコンビピスタチオなのに
完成すると可愛くなってる・・・塗装マジック！
Man, I wanna try that model kasten mucosal clear but too expensive to get from japan for one bottle. I also didn't realize you can mix it with enamel like that to have it work so well thank you for this learning and entertaining experience once again (more suction test please lol)
タイツの質感が凄い！
Id like to find some of the models you build and try them for myself, I learn so much from you!
Although I am not a big horror fan, you did a fantastic job.
i have tried your technique. but i am not good yet. it is so painful if the paint is removed by the masking. you make it look so easy! much respect!
I'd like to assume they use enamel paint, once fully cured it becomes incredibly difficult to remove even if you wanted to. Only issue is the cure time is like 72hrs or something like that so it would definitely prolong project times. Been tempted to try it but I'm way to impatient
@MegaDuckman19 not all are enamels. He still used a laquer primer as the first layer, which should be tough, but if you dont prep the surface good enough, there might still be release agent(from manufacturing of the garage kit) sticking to surface and that causes paint to peal off quite easily. He used an ultrasonic cleaner to prep the kit before painting, i dont have one of those as they are expensive.
@jetplane1989 I don't think the ultrasonic cleaner is needed just used as an extra precaution since he uses the abrasive cleaner. I will say I haven't tried these kits myself but these painting techniques helped me with my resin prints. So I don't deal with release agents but occasionally resin doesn't wash off completely in hard to get spots.
@MegaDuckman19 i wouldn't say it's a must have..but i certainly think it will make removing the release agent much easier. I soak the kit in degreasing soap overnight then scrub it with a toothbrush. But there always seem to be spots that I miss.
The spots that peal off in my gks are usually the nooks and crannies that my toothbrush probably didn't reach. It's such a pain when you have 4+ layers of paint, then the paint suddenly peals off with the masking tape. I dont have this problem with 3d printed kits. i skip the soaking and scrubbing entirely.
@jetplane1989 I can relate to that. Ive sworn off using the mask/tape until i know for a fact it won't peel off my hardwork. That said I balance between brush and airbrush as much as possible. Have you considered getting a cheap electric toothbrush? It may help get those nooks and crannies better cleaned, that combined with the degreaser it should work pretty well. unfortunately it can't be used for my resin prints due to the post processing.
これは造形師さんが喜ぶわーwww
beautiful work🥰🥰
新しいコーナー出来てる😆
黒スト具合いいですね〜😁
こんなに良い腕があるなら一般家屋や何か庭の小さなしし落とし庭とか、違う分野に挑戦したいですね、作品レジンで沈めてテーブルも良いです、花瓶もいいしレジンで固めて水槽に入れる物とか😊
可愛さエロさを感じずに芸術的な何かを感じる不思議さ。
551の豚まんって動画と関係ないとこに目がいってしまった😅
エロ可愛い感じが良いですね。
後、ケーキの柔らかい部分が白色なのが良いですね。
別な色だったら大変な事になっていますね。
下に配置したナイフ🍴等も良いアクセントになっているのが良いですね。
自分の最愛な亡き妻動物子供、女優等毎日見られる、仏壇に小さな母親とか
ケツと顔の超ミスマッチｗ
これを選んだ気持ちを知りたいｗ
🤔🤔🤔🤔🤔🤔🤔😍
💯
Score ☞ 💯🎉
🧛♂️🍷🦇🦇🦇