videocon lcd model t315hw04 bhai isme maine jo power wala cable andar gaya hai usme ek socket tha wo maine laga diya but ek green wire hai jo main bhul gaya kahan lagana hai sir plz bata dijiye
Bhai mai cap nhi lgata hun. Us time mera father ka death hua tha iske lie mundan karwaya tha. Islie kuch din tak cap lagaya krta tha ab nhi lgata hun. Anyways thanks for suggestion.
Bhai modual me 1.3 volt hota hai but likhta nhi hai usme 1.5volt ke bad se likha hoga 1.3v pane ke lie usme kisi bhi pin ko short nhi krna hai sirf input me GND aur 5volt denge to automatically 1.3volte nikalega check kr ke btaie
Mere pass Sansui ka 32 inch led hai yeah standard se release nhi ho Raha tha maine buck converter lagaya us k baad b on nhi standby release nhi huva voltage sab jagah lagbhag theek hai
Hello sir kal late night maine usko phir se check Kiya 3 4 bar on huva normal us k baad maine series se off Kiya phir se series mai lagaya phir se on nhi huva 😭
@@ATOZRepairing भाई WPM9435 1133 NOMBR की IC मे एक SIDE से चारो LEG मे 5V बता रहा लेकिन दुसरी SIDE के चारो LEG मे 0 VOLT बता रहा IC खराब हुई क्या. और KONSI IC है भाई ये.(standby fault है. Tv चालू nhi होता किसी भी key से.6-7बार ac switch off on करणे के बाद चालू होता है (SANSUI LCD 22'TV की है )
@@nandumeshram4656 bhai first to ic miter se nahi check ho paega Aur aapka jo problem hai wo hume lag rha hai pannel pe lage micro switch ka hoga ya fir software ka
@@ATOZRepairing 🤔भाई ये क्या.. आपने ही to vdo मे सारे ic multimeter से check किये है. जहाँ volt बराबर न मिले वहा fault बताया. और आप केह रहे की ic मीटर से chk nhi होगी.. To vdo मे क्या था. Ic chk कैसे करते है लोग. कैसे fault निकालते है. कैसे smjhte है ic damage है या good.😱. Pic send करता था but यहा optn nhi है send करनेका.
Ground se ho sakta hai canect Hoga Flash ic pe 3.3volt main supply check kijie pin no. Mujhe yad nhi hai Agar flash ic pe 3.3v ata Hoga to fir flashing karwana hoga
good morning sir. fls ic pin volt -- 1-0.03v, 2-3.2v, 3-3.2v, 4-G, 5-0v, 6-0v, 7-3.2v, 8-3.2v, prossr. me 1.3v aaraha hai. set stby. mode me hai, keya ho sakta hai ans me plz.
Bro flash ic ko abhi rahne dijie pehle wo jo mai 5pin ka regulator ic se ko btaya uspe voltage in aur aut ho rha hai ki nahi(jitna voltage mai btaya hun)
Sir Philips 32 inch tv me Screen 10 min off ho jati hai, sound ata rheta hai,. Backlight phele he change karai thi ab kya kru pura board change kr sakte hai kya
I have this board . 5 pin regulator ic was not working properly . I replaced it with a same buck converter that you have used here . all voltages became ok but no result yet . standby didn't released . MERA A SAME BOARD THA JISME 5 PIN KA REGULATOR KHARAB THA . MAI OOS IC KO NIKAL DENE K BAD A SAME BUCK CONVERTER LAGAYA THA . ALL VOLTAGE SAHI HO GAYA THA LAKIN CHALU NAHI HUA THA . KAYA PROCESSOR KHARAB HAI ? ISKA RESET SECTION KA TRANSISTOR BAGERA KANHA HAI ? PLEASE HELP .
@@ATOZRepairing mai mocro switch v chack kiya tha aur software v lagaya tha . memory ko nikal kar adoptor k through software dea tha kinwe ki a board vga k through program karne nahi deta . yodi memory kharap hota to rt809 to uska information deta tha . mai reset section ko dhundta hai . processor ko change ki age . what ever is it , up ko bohoot bohoot dhanyabad answer dene k lea .
Sar mere LED mein standby problem hai uske 5 peene wale IC per 1.3 volt a raha hai magar 8pin wale ic per 1.3 volt nahin pahunch Pa raha hai bata sakte hain sar kya problem hai.🙏🙏
Sir badiya se check kijie 5pin wale ic pe 5vo a rha hoga aur usse 1.3vo out karta hai. wo out nhi karta hoga Aur yadi ap confirm ho ki 1.3v out kr rha hai Aur flash ic jo ki 8pin ka hota hai uspe 1.3v nhi mil rha hai to ap jumper bhi lga skte hai. Video me btaya gya hai ki flash ic ke kis pin pe 1.3v in hota hai
Sir ji mere pas sansui ka crt tv he mujse sarvice menu se kuch galti ho gai ab tv me light hoti he lekin chalu nahi hota remote se aur mere tv me koi pennal swich bhi nahi he
Sory bro flash ic pe 1.3v nhi 3.3 volt aata hai wo mistak se 3.3v ke jagah 1.3 bol diya Agar 3.3 v nhi aa rha hai to baki ka regulator pe voltage check kijie
Wrong batarahe ho kabhi bhi flash ic me 1.3v nahi aata he through regulator. Jo voltage nihi aaraha o core voltage he jo ki processor ko jata he. Pahele khud thik se samjho phir video banao.aadmi ko galat jankari mat do....
Good and Great Speech for Anyone Person
Thank you and most welcome
Best information sir thank you
Welcome
Thanks sr very useful video
Thank you
Nice video bhai
थैंक यु सर
sir,god bless you
Thank you
sir ji very nice
Thank you
Very nice sir
Sir plz make video on clear eeprom problem
🇮🇳🙏👌nice teaching sirji 🙏
Thank you
Nice Sir g
Thank you
Hi friend I am आनन्द from ईरोड Tamil Nadu
Welcome
Good work
Sir l have already subscribed. Thanks.
Ok brother
तुम्हारे मुव्ही का म्युझिक बंद होता तो अच्छा सुनाई देता 😅
Sir video accha hai.lelin music bad
Ok bhai aage se music ka dhayan rakhunga
Thank you
Welcome
Thanks
Welcome
videocon lcd model t315hw04 bhai isme maine jo power wala cable andar gaya hai usme ek socket tha wo maine laga diya but ek green wire hai jo main bhul gaya kahan lagana hai sir plz bata dijiye
Facebook page pe photo vejie
Sir u made a good video but please do not wear cap when making video. At some places only ur cap can be seen.my suggestion sir.
Bhai mai cap nhi lgata hun. Us time mera father ka death hua tha iske lie mundan karwaya tha. Islie kuch din tak cap lagaya krta tha ab nhi lgata hun.
Anyways thanks for suggestion.
@@ATOZRepairingl am sorry bhai if l have hurt ur feelings .You making good videos with nice explanations.l m ur fan now.Many thanks Sir.
Sir 1.2 volt aana k baad regulator ic mein volt band ho jatha hai pls help 1.8 volt aur 3.2 nahi aata only one mein 3.3 aata hai
Sir mere TV me Bhi seme problame hai
Sir flash I. C. Ki pin no 8 per 3.3 voltage aata hai, 1.3 volts module me hoti hi nahi hai set kaise repair kiya plz Batay.
Bhai modual me 1.3 volt hota hai but likhta nhi hai usme 1.5volt ke bad se likha hoga 1.3v pane ke lie usme kisi bhi pin ko short nhi krna hai sirf input me GND aur 5volt denge to automatically 1.3volte nikalega check kr ke btaie
विडियो में टोपी ज्यादा दिख रही है।
Thankyou sir ji
Welcome
Can u replace my sansui led samart TV motherboard 40 inch TV plz reply
Ofcourse
Mere pass Sansui ka 32 inch led hai yeah standard se release nhi ho Raha tha maine buck converter lagaya us k baad b on nhi standby release nhi huva voltage sab jagah lagbhag theek hai
Software problem hoga
Hello sir kal late night maine usko phir se check Kiya 3 4 bar on huva normal us k baad maine series se off Kiya phir se series mai lagaya phir se on nhi huva 😭
जिस ic मे fault है ओ to तुम्हारी topi की वजह से दिखी ही नहीं. Aur उस्का voltage भी disply मे नहीं दिखाया. Main point ही गायब किया to repair करे कैसे 😇
Sorry brother
@@ATOZRepairing भाई WPM9435 1133 NOMBR की IC मे एक SIDE से चारो LEG मे 5V बता रहा लेकिन दुसरी SIDE के चारो LEG मे 0 VOLT बता रहा IC खराब हुई क्या. और KONSI IC है भाई ये.(standby fault है. Tv चालू nhi होता किसी भी key से.6-7बार ac switch off on करणे के बाद चालू होता है (SANSUI LCD 22'TV की है )
@@nandumeshram4656 bhai first to ic miter se nahi check ho paega
Aur aapka jo problem hai wo hume lag rha hai pannel pe lage micro switch ka hoga ya fir software ka
@@ATOZRepairing 🤔भाई ये क्या..
आपने ही to vdo मे सारे ic multimeter से check किये है. जहाँ volt बराबर न मिले वहा fault बताया. और आप केह रहे की ic मीटर से chk nhi होगी.. To vdo मे क्या था. Ic chk कैसे करते है लोग. कैसे fault निकालते है. कैसे smjhte है ic damage है या good.😱. Pic send करता था but यहा optn nhi है send करनेका.
@@nandumeshram4656 bhai vo volt check kiya continuity nahi
5lin ic se 5v in hoke flash ic ke knobar pin pe 1•3 de rahahe batia ga sar pelige
Sir circuit me btaya gya hai.
Alag se image ka bhi support diya gya hai usko dekhiye.
Thank you sir
Welcome
Flush ic par 3.3 volt hona chahiya .
Wrong janakari mat do bhai
Sair vidio sout sahikro thenkyu
Good video
Thanks
Ground pin pe kese voltage aayega or apni cap Nikalo pahle
Ground pin pe voltage nahi aaega yar ground pin pe - prode rakh ke check karna hai ho sakta hai bole me mistake hua hoga
Super
Mera Sansui led tv sjv22fh07fa model hai , is me on problem aa raha hai , red light batati hai but remote se tv on nahi ho rahi hai
Kya problem hai
Red light blinking pe ek video already hai usko dekhie
Sir videocon 32inches led me dubal image ke problem ko kisy shai karna hoga
Nice bro
Thank you
Sir 1.30volt tik hai par rilise nahi hota hai kya kare
Software dlwana hoga
Very nice
Sir same model h Videocon Ka regulator ic se 1.3 aa rha but flash ic ke 1.3 point pe nhi or jaha 1.3 ata h wo ground se short aa rha
Ground se ho sakta hai canect Hoga
Flash ic pe 3.3volt main supply check kijie pin no. Mujhe yad nhi hai
Agar flash ic pe 3.3v ata Hoga to fir flashing karwana hoga
good morning sir. fls ic pin volt -- 1-0.03v, 2-3.2v, 3-3.2v, 4-G, 5-0v, 6-0v, 7-3.2v, 8-3.2v, prossr. me 1.3v aaraha hai. set stby. mode me hai, keya ho sakta hai ans me plz.
Bro flash ic ko abhi rahne dijie pehle wo jo mai 5pin ka regulator ic se ko btaya uspe voltage in aur aut ho rha hai ki nahi(jitna voltage mai btaya hun)
App kanha se h
Mera bored samne h standby broblam h
Jhumari Telaiya, koderma, jharkhand
Glad IC kisi bhi pin me 1.3 v nahi aata h galaxy janakari may do pls
Flash ic pe kitna vo. Ata hai bro
Sir Philips 32 inch tv me Screen 10 min off ho jati hai, sound ata rheta hai,. Backlight phele he change karai thi ab kya kru pura board change kr sakte hai kya
Back light se bhi problem ho sakta hai aur bord se bhi pehle bord pe light ke lie supply check karna hota hai
@@ATOZRepairing ap kha se ho Delhi me ho to apko he dhoka dunga
@@rjroksregins4342 nahi bro mai Jharkhand se hun
@@ATOZRepairing Thanks
I have this board . 5 pin regulator ic was not working properly . I replaced it with a same buck converter that you have used here . all voltages became ok but no result yet . standby didn't released .
MERA A SAME BOARD THA JISME 5 PIN KA REGULATOR KHARAB THA . MAI OOS IC KO NIKAL DENE K BAD A SAME BUCK CONVERTER LAGAYA THA . ALL VOLTAGE SAHI HO GAYA THA LAKIN CHALU NAHI HUA THA . KAYA PROCESSOR KHARAB HAI ? ISKA RESET SECTION KA TRANSISTOR BAGERA KANHA HAI ? PLEASE HELP .
Check micro switch
Prosesar memory ic bhi khrab ho Sakta hai
@@ATOZRepairing mai mocro switch v chack kiya tha aur software v lagaya tha . memory ko nikal kar adoptor k through software dea tha kinwe ki a board vga k through program karne nahi deta . yodi memory kharap hota to rt809 to uska information deta tha . mai reset section ko dhundta hai . processor ko change ki age . what ever is it , up ko bohoot bohoot dhanyabad answer dene k lea .
Kitna paisa lagega thik hine me
आवाज कम, music ज्यादा सुनाई दे रहा है ...improve
Pahle aapke a video me background music math dhalo bhai 🙏
Ab nahi dalta hun pehle suru- sure me idea nahi tha video bnane ka
Sir ye 5v se 1.3v banane wali supply kaha milegi
Discriptin me link dal diya hun
Ek Videocon ka tv hai usme vertical line problem h or auto on off hota hai pani chala gya tha kya kru usme mujhe help kriye
Crt tv hai?
Esmae music ki kya jarirat thee.ye koi film chal raha hai kya
Music ki awaz itni tez hai ki apki baat kabhi kabhi samajh nhi aati
Sorry
Etna bada vdio banaya aur etne coment aaye lekin flash ic ki pin no, aspne nhi batai
Same problem my tv what to do how much will it cost me
Sir regulator ic 1.3 volt de raha hai pr TV on nhi ho raha ha?
Software problem hoga
@@ATOZRepairing kr liya sir wo 565 r module k wiring proper krna tha ok thank you😊
Flesh ic par 1.3 volt dene par fresh ic par volt drof ho raha hai 1.3 kya ho sakta hai Sir plzz btain
7805 ic kam nahi karega kya sir usme bhi to 5 volt out hota hai
Sir isme 1.3v ka jarurat padta hai
Regurater ki pehchan kon kitne voltage ka hai kaise pehchane
Good #circuiteffects
1.3 volt falsh ic me konti pin me aata hai
Bhai video ko pura dekha kije bariki se btaya gya hai. Circuit efect ke sath
Ground pin me aata hai kya
Sar mere LED mein standby problem hai uske 5 peene wale IC per 1.3 volt a raha hai magar 8pin wale ic per 1.3 volt nahin pahunch Pa raha hai bata sakte hain sar kya problem hai.🙏🙏
Sir badiya se check kijie 5pin wale ic pe 5vo a rha hoga aur usse 1.3vo out karta hai. wo out nhi karta hoga
Aur yadi ap confirm ho ki 1.3v out kr rha hai
Aur flash ic jo ki 8pin ka hota hai uspe 1.3v nhi mil rha hai to ap jumper bhi lga skte hai. Video me btaya gya hai ki flash ic ke kis pin pe 1.3v in hota hai
@@ATOZRepairing sir 1.3 volt supply flash IC per jumper ke dwara dene per bhi power beta de raha hai
Sar ji aapka contact number dijiye na please
Sir ji mere pas sansui ka crt tv he mujse sarvice menu se kuch galti ho gai ab tv me light hoti he lekin chalu nahi hota remote se aur mere tv me koi pennal swich bhi nahi he
Memory ic change kijiye thik hota hai to thik hai nhi to memory ko sam kit ka memory se new plane memory me copy kr ke lgaie kam kr jaega
Sir ager je ander se he 1.30v dena ho to
Jo section se 1.3v denge wo section ka voltage ampior kam ho jaega
@@ATOZRepairing sir ager dekhne me same part ho to je sambav he ke vo input 5v and output 1.30 dega jes ke kise phone parts
Ja fer headphone bluetooth ka same dekhne vala part
@@Harvindersingh-gl3dk nhi bhai
@@ATOZRepairing okay sir tanks
Ha...ha... Just joking , why are you wearing a cap ? any hairloss problem ?
Anyway , good information on Videocon,sansui kits problem.
Chutia patta anyway
🙏🙏🙏🙏🙏🙏🙏🙏🙏
Ok bro
Us time hmare pitaji Ka death hone ke Karan mundan karwae the. So....
Flash ic may 1.3 volt nahi aata flash ic may 3.3 volt aata hai
Ground PIN pe voltage kaise aata hai bhai
Bevkhup must banao
Kha ground pe voltage ata hai. Aur bewkuf kahe bnaenge saheb ho sakta hai kuch confusion hua hoga.
Videocon 32 inch lcd tv hai same board hai 1minut tak chalne ke bad standby mode me chala jata hai
Fir dubar switch on karne se turant chalu hota hai?
6 day tak chala fir stand by mode me chala gaya ab to stand by mode realise hi nahi ho raha hai
Please close the music & open your cap
Bhai yey galat hai flas ic ke 8 pin par 3.3v ata hai
Please can someone help me to find the dump of my TV philips lcd 32pfl5409/98 thanks in advance
My BPL TV on but after 5 minites off, what is the problem please reply me
The timer must have been set or it may be DRI solder
cap nekal ke kam karay
Videocon LED TV me Lal bati chalu hai remode se batan se TV chalu nahi hota hai batave reply to
Video ko follow karen
Sir FLASH ic pr 1.3v nahi aa rha hai
Sory bro flash ic pe 1.3v nhi 3.3 volt aata hai wo mistak se 3.3v ke jagah 1.3 bol diya
Agar 3.3 v nhi aa rha hai to baki ka regulator pe voltage check kijie
Sir mere pass Panasonic led hai standby ho chuka hai keya karu
I'm not getting 1.33 volt at Flash IC, but I'm getting 1.33 Volt at the regulator IC output. What Should I do?
Software Dal ke dekhie voltage Ka problem Nahi hai
Sir will we get the software
Sorry bro mai khud software Ka Kam Nahi karta
@@ATOZRepairing Ok Thanks a lot for the help. Can you suggest, is it available on line
Which is name that module
DC to DC step down converter
Sir ji voltage?
Voltage?
Ur number please
I'm from bangalore airconditioners pcb control service center 9845417775
agar lcd tv stand by mai chla jaye to kya krna chahiye
Aapki kep bich me nad rahi he use utar k video thik se banavo sahi trah se dikh nahi raha he
Capacitor ke pas 700 volte aa raha
700 volt नही आयेगा मीटर खराब होगा
@@ATOZRepairing aap mistri ho na ya u hi
Sir mere led 32 ench stand by par ye slow karna
Sir ji 1.2 digaye sir ok ho jayaga
Bhi Zara help kordo
Kitna kharcha ayega
Sir apki cap bichme bahot aati he
Sory bro
Us time mundan krwaya tha father ki death hui thi isi lie
Cap nekalken batav bichmay cap. Arahai
Sir aap top Bech mea aarahi he
Why so music in background
Sory
24 volt in 4 volt out ho raha hai capacitor par 3.2 volt aa raha hai kya karu
Bhai maine galat software daal diya uske baad tv stand by me chala gya h ab thik kaise kare please bataye
Dubara se sahi software dal liiie
@@ATOZRepairing bhai flash ho he nhe rhe h....card read he to nhe kar rha h...sahi firmware flash nhe ho rha h
koi purana bord same bord hai to uska 8pin wala flash ic change krke dekh lijie
@@ATOZRepairing wahi to problem h h bhai universal board koi aur dusra to nhe h
apane flassh IC ka 4 no pin per jo 1.3v bataya vah to already ground Hai To Apne a galat bataya
Remove the cap can't see
Bhai meri 25v_to 5v ic jal gyi kya karu
Ic kyo jal jaati hai
Ham chek kiya hu lekin nahi ho raha
Wrong batarahe ho kabhi bhi flash ic me 1.3v nahi aata he through regulator. Jo voltage nihi aaraha o core voltage he jo ki processor ko jata he. Pahele khud thik se samjho phir video banao.aadmi ko galat jankari mat do....
Sir ji iss tarah ki aur bhi video banaye led card stand by fault wali and panel repair ki video jaroor banaye
Icd
Kaphalasickanambar
Reguletarnambar
Sirf topi nikalo yaar
White
White display kya kare
Topi htake kar bhai
😅😅😅😊😊