Table Saw Build - Part 2 : Angle Tilt Mechanism ➲ DIY WoodWorking For Aug16
Вставка
- Опубліковано 6 лют 2023
- Plaese subscribe to 【DIY WoodWorking For Aug16】Channel on UA-cam if you like my videos: / @ordinarydaily
Turn on the little bell🔔 notification, the firs time to watch wonderful video~ - Навчання та стиль
You do have to spend some time setting the saw up... blade, fence, etc. But once done, the saw is great. Fairly compact which is Nice ua-cam.com/users/postUgkxXh-4_3-ZT1fFWP91ZV7iVqzElr0lEb-a I did get an Incra Miter Gauge which takes some setup as well. The stock miter gauge can be adjusted in the miter slot with a little painter's tape... this tightens up the side to side play a lot.
Beautiful job there on the tilting and height adjustment my friend.. I am about to attempt my own build soon. The thing is I have most of it set up but I want to put a tilting mechanism on my saw with the 2nd wheel but I'm a little stumped by the whole thing. I will work it out but this video has given me a slight hint into a great way of building it into my saw. Thanks for that my friend.. Appreciate it very much. Keep up the great content..
Nice job 👍
It is nice.
LIKE👍👍 👍👍 👍😍 😍😍 😍🍀🍀🍀🍀
Great engineering! Can't wait to see more!
Hey there man.. I have a question if u have a moment to answer for me my bro. I'm about to begin my table saw build. I'm using old parts rom a cheap table saw so I have a bit of a head start but wht I cannot figure out is how u managed to get the blae to come up in the same position as u would for 90 degrees and 45 degrees. I would like to completely rebuild from scratch but that part I cannot get my head around. My table will be 1000mm (length) x 500mm (width). Is there a specific place I would need to place the whole saw mechanism to get it towork as well as u got it to work? What I mean to ask u is placement all important.
I will be using some old parts from a cheap table saw with a 1500W motor. Hard start but I have the lift mechanism in there. What I want to put onto my new built saw is the tilt mechanism. So I guess my question is this.. Is where I place the tilt bar & mechanism more important to getting the blade to come out correctly as it does in the lift mechanism. I guess I'm asking daft questions here but I hope u get what I'm trying to ask u bro..
I haven't built a Table saw before so I would like to get it right. I'm using 40x40mm Sq tubing. I have some 25x25mm tubing too and some 50x25mm also. I bought the 40x40mm angle bar to build the fence aswell. I'm going all out bro but I don't want to mess it up.
Any advice u could give me on the Lift & Tilt Mechanisms would be gratefully received by a fellow saw builder. At least I wanna say I'm going to do my best.
Love the channel bro. Been sub'd for a good while. I shared the channel and video but I'm only getting back onto twitter now. I lost a load of ground there. I had a few thousands followers but they're all gone. I don't know what happened. I musta said something that wasn't liked. I can get a wee bit political sometimes and rub ppl up the wrong way.
TGake it easy bro and keep up the awesome work.. I love ur table saw build..
Гайки, которые заколачиваются (с шипами) - их не нужно фиксировать дополнительными саморезами. В них винты (ручка ч резьбой) закручиваются с ДРУГОЙ стороны доски!
Если по ручке ударить в торец ,то эта гайка вылетает !
امتياز
The video is great but the music is very annoying.
It's hard to understand 🙄