thank you sir! I just got this machine and you explained the process very well.. 👍🏼👍🏼👍🏼maybe you might consider doing a video on how to change the blade..it will surely help us..
For that money, the saw is good. Minor blade settings are required. It can also be exchanged for a better quality blade. Depending on needs. The saw is useful. Of course, saws are better. It also depends on how much money you are willing to give for the saw
i just got this (slightly different new black "model", same model name, and seems identical) after watching this. Seems pretty fabulous for the price so far, especially considering it has slow gear for metal as well. Thanks for the demo. Is yours holding up well?
use an angle square and place it with the blade and the working area top..if it wobbles unscrew the lower screw as that one is to adjust the 90°angle. do that until the angle square is 90° with the blade and working area..if not tighten abit again until you have a 90° angel...the same process is for the 45° but unscrew the the top screw and then tighten accordingly when you have a perfect 45° with the square
To anyone who has this machine. Maybe this is a weird question, but if you look at the back of the machine where the tubes slide in and out, is there a bearing only on one side? A lot of sawdust goes in one side on mine because no bearing/gasket there, and i wondered if this is cost savings or an oversight at the factory. Thanks :)
Just bought my saw from lidl ,is the adjustment of the blade for plumb just trial and error? Mine is neither cutting plumb or square from the fence, I can move the fence easy enough not so sure about getting it plumb
Very informative video, thank you! I have the exact same machine but somehow all the angles on the rotary table are a bit off. Is there any way to adjust this? If I use the full extension of the rods and try to cut at 90 degrees there is 2mm difference between the beginning and end of the board
Hello. Today I tried cutting the 345mm wide board twice and everything was ok. Maybe it made a little difference by less than 1mm. Very little. Almost nothing
@@michaelhill5298 i haven't been able to get it aligned perfectly. There always seems to be some play in the 0 degree setting also even after locking it in place which is not helping either.
bonjour a vous et merci pour vos explication de la PARKSIDE SCHEPPACH PZKS 2000 A1 nouveau model, j'ai un soucis avec le laser car il n'indique pas vraiment l'endroit ou la coupe de la lame se fait ??? Bien a vous Claude
I have b2 table saw 2000 watt cant get the motor repaired armature is a tooth missing needs a copper insert to be repaired. cost as much to repair may wells buy new tablesaw
It is possible that the saw blade does not cut well. It is not of such high quality. A universal saw blade is not exactly good for hardwood. It is important whether we saw transversely or longitudinally and depending on this we need to use a suitable saw blade. They differ in the angle of grinding and the number of teeth. With fine teeth, sawdust accumulates and then begins to burn. Maybe too much pressure on the wood during sawing at all on hardwood
@@darijan-diy thank you for explaining. I will buy a better brand saw blade. The wood that I use is douglas. Not really hard wood but kind of. Can I buy any kind of brand or am I stuck to the ones from Parkside? And which size is this one? We have the same like you have in the demo
Does any posibility for cut to zhe end of back side ? 30 mm cant cut if blade dont cut all high of part? Ima li rešenja za uzadnju stranu komada ako se ne sece ceo komad nego useca kanal na odredjenoj dubini kao što je na videu?
@@milosvukovic2270 Da to je problem. To možete rešit tako da iza ove daske koju radite stavite jednu nižu dasku tako da je ova koju radite napred prema vama onda žaga ide ravno nazad
Dober video. Pravkar je v akciji PZKS 2000b2 za 100eur. Po karakteristikah bi raje typ kot je vaš. Imate inf. kje kupiti. Kakšne izkušnje imate po 4 mesecih uporabe?
Hvala za komentar in ogled. Jaz sem to žago kupil v Lidlu za približno 155eur. Kje bi jo lahko v tem trenutku kupili žal ne vem. Z žago pa sem zadovoljen. Na zadnji strani nameravam naredit nek lijak za odsesovanje praha
@@simk33 Hvala za prijaznost. Pravkar govoril z Lidl info glede max višine reza obdelovanca. Bodo posredovali v tehn. službo nabave in odgovorili. Čakam povr. inf
Darijan, excellent video! Could there be a way to install a 305mm disc blade on this saw to cut 100mmx100mm beams in one single cut? Darijan, odličan video! Ima li možda neki način instalirati na tu pilu list promjera 305mm kako bi se mogle rezati grede 100mm x 100mm u jednom potezu? This kind of disc blade 305mm/30mm, ie: Ovakav list pile/žage 305mm/30mm, na primjer: www.amazon.co.uk/dp/B081H7L3DP/ref=dp_prsubs_1
thank you sir! I just got this machine and you explained the process very well.. 👍🏼👍🏼👍🏼maybe you might consider doing a video on how to change the blade..it will surely help us..
Thank you 😀
Also a very good presentation. Simple and easy to understand. Thank you.
Thank you for watching
Thank you.
220 subs - 64k views well done. Pozdrav Darijan.
Final opinion on this one? Good for the money? Any other better saw?
For that money, the saw is good. Minor blade settings are required. It can also be exchanged for a better quality blade. Depending on needs. The saw is useful. Of course, saws are better. It also depends on how much money you are willing to give for the saw
i just got this (slightly different new black "model", same model name, and seems identical) after watching this. Seems pretty fabulous for the price so far, especially considering it has slow gear for metal as well. Thanks for the demo. Is yours holding up well?
Thank you. Yes it's still holding up well.
Can somebody explain how the process of adjusting the blade with those 2 screws works? What does it do exactly and how do you do it?
use an angle square and place it with the blade and the working area top..if it wobbles unscrew the lower screw as that one is to adjust the 90°angle. do that until the angle square is 90° with the blade and working area..if not tighten abit again until you have a 90° angel...the same process is for the 45° but unscrew the the top screw and then tighten accordingly when you have a perfect 45° with the square
i think the screws adjust the blade to tilt to 90° and 45°
To anyone who has this machine. Maybe this is a weird question, but if you look at the back of the machine where the tubes slide in and out, is there a bearing only on one side? A lot of sawdust goes in one side on mine because no bearing/gasket there, and i wondered if this is cost savings or an oversight at the factory. Thanks :)
I did not understand
I believe there is only a black rubber gasket on one side, which is there to stop the rails from bumping into the body during sliding.
@@cdinusha1 thanks 🙂👍
Excelente!👍
Is it possible to cut metall if we change the disk?
Unfortunately, I don't know that. I never thought about it because I have a saw specifically designed for cutting metal. I think not
I would love to see verdict at the end of video.
For this money, the saw is ok
Just bought my saw from lidl ,is the adjustment of the blade for plumb just trial and error? Mine is neither cutting plumb or square from the fence, I can move the fence easy enough not so sure about getting it plumb
Very informative video, thank you! I have the exact same machine but somehow all the angles on the rotary table are a bit off. Is there any way to adjust this? If I use the full extension of the rods and try to cut at 90 degrees there is 2mm difference between the beginning and end of the board
Hello. Today I tried cutting the 345mm wide board twice and everything was ok. Maybe it made a little difference by less than 1mm. Very little. Almost nothing
I have the same problem, did you find any way to solve it ?
@@michaelhill5298 i haven't been able to get it aligned perfectly. There always seems to be some play in the 0 degree setting also even after locking it in place which is not helping either.
bonjour a vous et merci pour vos explication de la PARKSIDE SCHEPPACH PZKS 2000 A1 nouveau model,
j'ai un soucis avec le laser car il n'indique pas vraiment l'endroit ou la coupe de la lame se fait ???
Bien a vous Claude
Nice video.
Thank you for review.
In my country i can buy only the 2000 B2, it is better than your A1?
I don't know that
I have b2 table saw 2000 watt cant get the motor repaired armature is a tooth missing needs a copper insert to be repaired. cost as much to repair may wells buy new tablesaw
Das bis jetzt die BESSSSSTE SÄGE die Lidl hatte 😍😍😡😢😢😢 die MPKZ 2000 A1
DEN die PZKS 2000 B2 ist echt doooof
Hast du die Säge schon mal für Stahl benutzt?
Хочу купить, рекламации классные,а на самом деле как она кто подскажет.
Good one
😀👍
Sometimes the machine have difficulties to cut. The wood is burned at some places
How come?
It is possible that the saw blade does not cut well. It is not of such high quality. A universal saw blade is not exactly good for hardwood. It is important whether we saw transversely or longitudinally and depending on this we need to use a suitable saw blade. They differ in the angle of grinding and the number of teeth. With fine teeth, sawdust accumulates and then begins to burn. Maybe too much pressure on the wood during sawing at all on hardwood
@@darijan-diy thank you for explaining. I will buy a better brand saw blade. The wood that I use is douglas. Not really hard wood but kind of.
Can I buy any kind of brand or am I stuck to the ones from Parkside? And which size is this one? We have the same like you have in the demo
You can buy any brand of blades. Just pay attention to the size of the blade and the center hole. Blade size fi 255mm x fi 30mm
Si può usare anche la lame x alluminio ??
Does any posibility for cut to zhe end of back side ? 30 mm cant cut if blade dont cut all high of part? Ima li rešenja za uzadnju stranu komada ako se ne sece ceo komad nego useca kanal na odredjenoj dubini kao što je na videu?
Ne razumijem tačno kakvi problem imate.
Problem isti kao u videu od 4:50 do 5:11 minuta .
@@milosvukovic2270
Da to je problem. To možete rešit tako da iza ove daske koju radite stavite jednu nižu dasku tako da je ova koju radite napred prema vama onda žaga ide ravno nazad
@@darijan-diy Hvala .Uradicu tako .
Dober video. Pravkar je v akciji PZKS 2000b2 za 100eur. Po karakteristikah bi raje typ kot je vaš. Imate inf. kje kupiti. Kakšne izkušnje imate po 4 mesecih uporabe?
Hvala za komentar in ogled. Jaz sem to žago kupil v Lidlu za približno 155eur. Kje bi jo lahko v tem trenutku kupili žal ne vem. Z žago pa sem zadovoljen. Na zadnji strani nameravam naredit nek lijak za odsesovanje praha
ce kaj pomaga je od cetrtka 16.7.2020 spet v Lidlu. Jaz jo bom vzel....super razlaga glede masine...hvala :D
@@simk33 Hvala za prijaznost. Pravkar govoril z Lidl info glede max višine reza obdelovanca. Bodo posredovali v tehn. službo nabave in odgovorili. Čakam povr. inf
Wo bekomme ich diese Parkside MPKZ 2000 A1 - IAN 315340 her !??????
Lidl
@@darijan-diy leider nicht ich suche seit TAGEN nach dieser Maschine 👻😡😡😡
Dieses gerät können sie nur bei Lidl kaufen wenn es eine aktion gibt
@@baschticz
Jetzt ist sie wieder zu bekommen
Würden Sie die Maschine weiterempfehlen?
Ja
Troppo rumorosa😵😵😵
Sce aonglet radial
Darijan, excellent video! Could there be a way to install a 305mm disc blade on this saw to cut 100mmx100mm beams in one single cut?
Darijan, odličan video! Ima li možda neki način instalirati na tu pilu list promjera 305mm kako bi se mogle rezati grede 100mm x 100mm u jednom potezu?
This kind of disc blade 305mm/30mm, ie:
Ovakav list pile/žage 305mm/30mm, na primjer:
www.amazon.co.uk/dp/B081H7L3DP/ref=dp_prsubs_1
Hvala na komentaru. Maksimalni promjer zaštite lista je 280mm. To je bez one zaštite koja se diže kad spusti pilu. Tako da list od 305mm ne ide.
@@darijan-diy Hvala na odgovoru, i još jednom svaka čast na odličnoj recenziji pile Parkside MPKZ.