That looks... both fun and utterly terrifying! The welding was... functional, but the front and rear hub shafts clearly showed they weren't up to the task at the end with their buckling as badly as they did, welding those bearings to the body was just crazy, you had a lathe there, so why didn't you turn a length of pipe to accept the bearings and do that properly? Finally, the way that front wheel sticks so far forward of the turning point made it look excessively unstable... Fun to ride? definitely. Safe? NOPE!
Man that thing looks like fun!! The front tire is too far out though. Makes the bike want to fall into turns. See if you can find the 90cc version of that engine and put exhaust on it. I want to ride! Keep learning and keep building!
one thing you need to do to get nice looking welds : make the parts verry clean , no rust or paint and wipe down with acethone , you be supprized how mush difference that makes on youre welds the way you made the frontfork puts the wheel at a too big angle from the hing / turn point of the steering . you could make the downpipe bend more toward the motor and have the axle of the wheel in line with the turnpoint , will make the steering a lot lighter and doesnt give the feeling that the bike only wants to drive straight ahead the jackshaft is a good idea but placing it under the hinge of the rearfork will cause the chain to tension as the bike sags down
All in all you have to give this guy credit take a look at where he’s at what he’s working with in my eyes this guy could’ve been one of A great engineer
I just watched this to the end to see what gives up first, the overly elongated axles or the fork. I also knew the chain will make problems. At this speed it might work, at any higher speed the constant change in chain-tension will either cause the chain to jump out or rip.....the suspensions are not....how do I say that...very sophisticated
That thing is a death trap, but looks cool tho! lol.....Put a chain tensioner on it so the chain isn't so sloppy. Also, I can tell that the rear tire is starting to tilt sideways because the one bolt holding it cant hold the weight of the rider, you somehow need to stabilize the rear wheel better.
Good idea But rong way of doing it and single sided is always hard to do . Try a bigger swing arm of a 600cc or bigger for the size of wheel and make bigger triple trees for front
It's not a good idea... Swing arm needs stability and the drive chain might tangled with it's swing arm.. front wheel must be smaller than the rear wheel so it's easy to balance and to do the turns... However,,,, you guys are are creative...
A very good idea.. But for sure u gonna learn a lot with that project.. The convertion, the extension of the front wheel from the center, the rear shock absorver position, welding procedure, the thickness of the tubular you used, welding with the bearings... Anyway sir still a good concept of modification..
I’ve seen a lot of these type of videos... I would have to say this one was a epic fail.
@CruzRedEye probably better then this one
@CruzRedEye para hacerlo como este mejor no lo intento jaja
I agree, you know anything about torque vs stress you would the welds will snap sooner than later.
I wouldn't bother with this Ogre its a trash .....waist of time and space
It's good that the workers where wearing their safety Steel toe flip-flops.
😂😂😂😂
That looks... both fun and utterly terrifying!
The welding was... functional, but the front and rear hub shafts clearly showed they weren't up to the task at the end with their buckling as badly as they did, welding those bearings to the body was just crazy, you had a lathe there, so why didn't you turn a length of pipe to accept the bearings and do that properly?
Finally, the way that front wheel sticks so far forward of the turning point made it look excessively unstable...
Fun to ride? definitely.
Safe? NOPE!
👍Fantastic welding skills! 🤣
LOL
Haha
maestros artesanos 🤣
Приваривать подшипники, имея токарный, это по крайней мере идиотизм!
Man that thing looks like fun!! The front tire is too far out though. Makes the bike want to fall into turns. See if you can find the 90cc version of that engine and put exhaust on it. I want to ride! Keep learning and keep building!
Все законы механики и ФИЗИКИ нарушили. ...
Поржал от души . особенно в конце
колёса хорошие,жаль дуракам достались!!!, на 53 минуты этого ананизма меня хватило!!!
Тигом варит как автогеном😂😂😂😂😂
там во второй части не менее весело !
@@voi_vetra боюсь нервов не хватит
wahh keren sekali, sukses selalu 🤗👍
Có lẽ một chút công việc mới nữa sẽ tạo ra một chiếc xe máy tốt hơn. Làm tốt lắm.👍👍👍👍
Creatif and fantastic
great motorcycle, you did a great job.
That thing sounds like it should be blowing bubbles.
it's a cool project it's interesting, it was just poorly designed
Сварка божественная
Super kreatif sukses selalu GBU
This is very entertaining and so fun to see the man try so hard to control that *Monster Bike*
Awesome Welding... LOOOOL
Big Time Death Trap...LOL
Перед сваркой надо говорить: "Глаза-а-а!!!"
first i though this is foreigner built. but after i look at license plate.. ភព២ hahaha the best
cool bike you guys got style and talent great video 💎💎💎💎💎💎💎💎💎💎💎😎✌️
Muito bom Campina
Perfect
Ain't gonna watch the whole thing, but starting the video with the acoustic knockoff version of " I used to love her" by GNR was a nice touch.🤘
Great video👍👍
one thing you need to do to get nice looking welds : make the parts verry clean , no rust or paint and wipe down with acethone , you be supprized how mush difference that makes on youre welds
the way you made the frontfork puts the wheel at a too big angle from the hing / turn point of the steering . you could make the downpipe bend more toward the motor and have the axle of the wheel in line with the turnpoint , will make the steering a lot lighter and doesnt give the feeling that the bike only wants to drive straight ahead
the jackshaft is a good idea but placing it under the hinge of the rearfork will cause the chain to tension as the bike sags down
sus soldaduras dan miedo amigo con toda esa roña
Chạy nhanh mang theo cái rổ
để lụm răng
Ổng chạy nhìn mắt gầu quá 😂🤣
Glass tig amazing skill😎👏👏🤣🤣🤣
Sandals open fly wheel and chains, sounds like a good idea
waaaah mantap keten
Nice and powerless.
Wooow keren banget
You're the cleverest 😃 good luck
A nice work for modified skill
Indians are very creative indeed lol
44:50 судя по звуку он на мыльных пузырях работает)))
чувак тебя смутил звук в этой поделке ? Печально , ведь это единственное что здесь работает как надо!
@@voi_vetra да даже если так, забавно же звучит)))
All in all you have to give this guy credit take a look at where he’s at what he’s working with in my eyes this guy could’ve been one of A great engineer
I just watched this to the end to see what gives up first, the overly elongated axles or the fork. I also knew the chain will make problems. At this speed it might work, at any higher speed the constant change in chain-tension will either cause the chain to jump out or rip.....the suspensions are not....how do I say that...very sophisticated
Рейк, трейл- не, не слышали. Потери на дополнительные передачи - да пустяки... Вес модифицированного мопеда: + 1000 килограмм... Рукозад модифиед.
Tôi lậy ông máy Hàn đầy đủ toàn hàng xịn vậy mà hàn như bò gặp cỏ😂
Some kind of brake would be a bonus.
Took a perfectley good bike and transformed it into something unrideable .Well done ;-).
Cek urang mah nu kitu mah moal kapake ka nyaah nyaah bahan😂
Well it looks cool….
That thing is a death trap, but looks cool tho! lol.....Put a chain tensioner on it so the chain isn't so sloppy. Also, I can tell that the rear tire is starting to tilt sideways because the one bolt holding it cant hold the weight of the rider, you somehow need to stabilize the rear wheel better.
На первой кочке сломается вилка, на второй порвёт цепь, да и от нагрузок поведёт заданию вилку
I would never trust those welds. Cool factor but the welding is too scary to ride
베스파 의문의 미소^^
You got your TIG welder toooooooooooooooooooooo hot
Creapy wkwk pro arm 🤣🤣🤣
Project “FAIL" 😂
Потенциальный убийца на дороге, даже тормоза не приварил ))))
Good idea But rong way of doing it and single sided is always hard to do . Try a bigger swing arm of a 600cc or bigger for the size of wheel and make bigger triple trees for front
Нужно было переднее колёса делать ближе к раме , да и заморочек было бы куда меньше
и колесо изкревилось заднее и сварщик видимо только в торой раз варит за жызнь
A lot of work for something that's not going to last. The frame is flexing every time they turn it.
That's a death trap but I appreciate every build tho
1 amazing car
modification is not for daily. when crossing a damaged road, the frame must be broken. also looks unstable when driving.
great wheel construction 🤣
Why's it sound like Willy Wonka boat in the chocolate River? Also. The geometry on that steering is wild.
Ön ve arka şasiyi bükülmüş borudan yapın hem sağlam hem estetik olur.
It wont last long but gud work guys
You get better at welding and things will be better for you I can promise you that for sure
respect the creativity. but it just hurts my pride as a welder. should learn to weld more. then can proceed to weld for quality and safety.
Cómo conseguiste el rin y la llanta en dónde la compraste
Watching the suspension part actually baffled me!
Buena idea, mal ejecutada... Muy mal ejecutada jajajaja
You should be cleaning everything if your going to tig.
Wow nice one, where can i purchase that kind of rim and tyre?
Yo let’s build a moped I can’t ride
osum!!!
Amazing
COOL
motor ke ape tu. teruk nau🤣
Sin frenos, y con esas terribles soldaduras entre otras maravillas de la mecánica y de la metalurgia. Qué puede salir mal?
1:00:00 Best bike in the video. Honda Grom in the back.
no se les ocurrió lubricar a la hora de hacer agujeros en metal no se digo así para no destruir mas rápido las puntas
All good but shock absorber on front suspension arm needs to be at least with plastic sleeve or ball bearing not metal in metal.
looks like a death trap!
Xích cọ vào càng sau thế kia mà vẫn lắp để đi được
Mais que dois je dire, nous les bricoles avons toujours un tour sous la main
All tht time to watch them build this slow shyt! Damn it have the motor of a drill n it or what
It's not a good idea... Swing arm needs stability and the drive chain might tangled with it's swing arm.. front wheel must be smaller than the rear wheel so it's easy to balance and to do the turns... However,,,, you guys are are creative...
Where can I get a set of those safety sandals?
Get some smaller fill rod. You won’t have to get so much heat out of your tungsten and will be able to get a puddle of molten mettle to flow.
Fail but cool
Nice project guys. Looks like a lot of fun. Maybe a little work on the front end for better steering. Real good job. Cool bike!
👀
Dapat sa swing arm kayo nag modified panget ng swing arm hahaha
en la llanta delantera no debe ser ancha.
very beautiful. i want to make one for my own now.
try changing the gearing to make it faster good luck :]
You can literally see it bending more and more out of shape as they are riding it , why they went for single sided swing arms I have no idea 😂
)c
Looks like it's gonna fall apart at any moment.
That's the bubbliest motor I have heard in my life 😂
🤣🤣🤣🤣
A very good idea.. But for sure u gonna learn a lot with that project.. The convertion, the extension of the front wheel from the center, the rear shock absorver position, welding procedure, the thickness of the tubular you used, welding with the bearings... Anyway sir still a good concept of modification..
Good little sheep wearing there masks.
Joy mai yaaa, that shits gonna twist any second, needs a redesign & another builder 😅
Ön lastiğin yere sürtünme yüzeyi fazla olduğunda dönüşlerde motorsikletin dönüşünü zorlaştırıyor