my friends and i made this for our school's project and we did it successfully! our teachers complimented on us and they chose us to be the best group! thank you, diya funplay! i love you so much muach xixixi 🥰😋😝💌😘
Sir,I have to show this in my school and I m not able to carry table fan or dryer so can u plz tell me where can I fix battery in this according to ur discription plzzz reply because I have only 2 days to make this 🙏🙏
@@parirajput6417 Yes, i will make a video as soon as possible. But, connecting a battery and a switch is relatively easy. Just connect one end of the wire to a motor. There will be two wires. Wire for positive will be red and the wire for negative will be black. Connect one side of these wires to the motor and the other side to a 9Volt battery. You will need a battery cap for this battery to connect the wires. And finally, cut the positive(red wire) alone somewhere in the middle and connect a switch. Connect the ends you had cut to the two terminals in the switch. If you still have doubts, let me know and i will upload a video tomorrow.
Yes you're right. Good observation. One of the blade slipped slightly while fixing with hot glue gun (went out of angle limit). Glue went solid before i could adjust it. So left as it is. Thanks for mentioning.
Sorry that i missed out the dimensions in this project. For the turbine blades you can use a cardboard of size 30X14cm and the tower should be 40 cm tall. You use the other dimensions accordingly. Please let me know if you need any other clarification.
Items needed for this project: Cardboard, Thermocol (only if you want a sturdy base) hot glue gun wires, led bulbs, switch, dynamo, generator or dc motor (as you need) scissors.
VERY GOOD , BUT ... I have tried with a dc motor and it will not light up unless I spin the blades at almost 1000-RPM using a pc blower , how did You get it right with such a slow turn rate on the shaft ?
That is a small pulley attached to the motor shaft. That is really not needed for this project. Some dc motors have gear wheels and some have pulleys and others may have wheels too. You can ignore it.
Fun play time ki bacchi tere Jo video hai na sare link mein dal deti hai tu khud dikhaya karna sab kuchh itna information deti baithe ho usse achcha to vah acche to vah Riaz fan play time
Items needed for this project: Cardboard, Thermocol (only if you want a sturdy base) hot glue gun wires, led bulbs, switch, dynamo, generator or dc motor (as you need) scissors.
@@diyasfunplay i did same as you shown in the video. But after switch on the table fan and took the project to front of table fan,Only the motor is running and the light is not working.
Check and make sure that all the connections are correct. Check your generator/dynamo specifications. It should be a "low rpm generator". Normal generators will need more than 1500 rpm to generate electricity. But low rpm generators can generate electricity at a very low rpm. The turbine in my model rotates at around 80- 100 rpm. Only low rpm generators can generate electricity at this rpm. If all connections are correct, then the problem could be with the motor (not being able to generate enough electricity). Also make sure to use a low watt led.
Wind turbine explanation:
ua-cam.com/video/gNGyMtVf4iY/v-deo.html
Itna mehnat kaun karega
i've finished this and i won a competition
Well done 👍👍👍
Same
my friends and i made this for our school's project and we did it successfully! our teachers complimented on us and they chose us to be the best group! thank you, diya funplay! i love you so much muach xixixi 🥰😋😝💌😘
Great job! & Thanks for sharing! All the best
I got first position in my science because of your hard work thanks a lot
Well done!
this is perfect for my simple machine project (wheel and axle)
All the best 👍👍👍
Thank you very much it helped a lot in my project
Great 👍😊😊
This is perfect for a a hool project
school*
By the way, it was amazing
Awesome bro
Thanks 🤗
Woah ur so fast at making things!
It's a filter that speeds up the video
The video is speeded up dude
@@brooklyn_noine_noine ikr
Thank you sir. It helps me for making best science project in my science fair
All the best 👍👍👍😊😊😊❤❤❤
Thanks i will use this for our project wind mill to our subject CPAR
Good luck!
You are great bro speech and windmill
Wow wow that is cool i mean press to make it out of cardboard you get a prize you got five stars
Thanks a lot
Awesome blade shape
Thanks
It's the best design for my project thank you sir for your wonderful project 👍👍☺️😊😊❤️🙏
Thanks a lot
nice job! i love your works... i've finished this work and i've presented the work to my whole class and i got the best category 😍🥰
Awesome, thank you!
interesting 😲
Thanks a lot 😊
Thank you 🙏 nice project is project ki vajah se mujhe first prize Mila
Great 👍👍👍
it is better to make it help people 💪💪💪👍👍👍👉
Thanks for the visit ❤❤❤👍👍👍😊😊😊
Amazing😍😍😍😍😍😍😍
Thanks 😄
Thanx bro for idea
Thank you too
Good
Thanks a lot 😊😊😊
wwoooww its like a real one ,,,😍,,,
i also make a solar and wind turbine model power house ,,,,
Thank you very much 😊😊
beautiful
Thank you! 😊
We are making lighthouse so we need wind mill for say that the wind energy claimed at lighthouse and give light ti boats thanks
All the best
The thing I was searching for
Nice
Thanks
Really good for school project
Thank you so much this video helped do much for my school project thank you 😊👍👍👍
You are welcome 😊
Superb
Thanks...
Its ok sir
Very nice 👍🙂
Thanks
You are a genius genius 🙏🏘️🏘️
Thanks a lot....
Excellent work
wow it's awesome!!!
Thank you! 😊
Btw. It's amazing
👍👍👌
Thanks 😊
Its binod .. not binoy
Wonderful
Thank you
Nice job! What are the specs of the capacitor soldered to the motor terminals?
thanks
You're welcome!
The wires you are showing in the motor can be found at any electrical shop.
Hello sir! Could you please tell me the specification of the motor? Which one should I buy to make this working wind turbine?
You need a very slow rpm dynamo for this turbine. Somewhere between 10 to 90 rpm. Lesser the rpm, better will be the output.
where can I find the measurements? Btw an Amazing build!
Sir,I have to show this in my school and I m not able to carry table fan or dryer so can u plz tell me where can I fix battery in this according to ur discription plzzz reply because I have only 2 days to make this 🙏🙏
You can fix the battery and a switch at the tower base platform (bottom cylindrical structure)
@@diyasfunplay ohhh thanku sooo much sir
Sir can u plz make a video on this because I have never done this type of work so I have no experience and no one is here for help
@@parirajput6417 Yes, i will make a video as soon as possible. But, connecting a battery and a switch is relatively easy. Just connect one end of the wire to a motor. There will be two wires. Wire for positive will be red and the wire for negative will be black. Connect one side of these wires to the motor and the other side to a 9Volt battery. You will need a battery cap for this battery to connect the wires. And finally, cut the positive(red wire) alone somewhere in the middle and connect a switch. Connect the ends you had cut to the two terminals in the switch. If you still have doubts, let me know and i will upload a video tomorrow.
@@diyasfunplaysir help me please... How can i connect led, motor, switch simultaneously...
there is weight on blades
try to measure the blades
one of them isn't in the right place
Yes you're right. Good observation. One of the blade slipped slightly while fixing with hot glue gun (went out of angle limit). Glue went solid before i could adjust it. So left as it is. Thanks for mentioning.
Why a cone ahead
To reduce drag at high winds 😊
Whats the length of the blades...please tell measurements of blades
Around 25 cms
how to put motor and generator together
I have used only a generator. I would have mentioned the generator as motor in my comments, But, I have used only one generator for the wind turbine.
How big is the circle the blades are attached to?
Miss is this phenomenon can be called as uniform circular motion?? I have to do a model regarding uniform circular motion can u help me pls....
I am like
Thanks a lot
Can i use dc motor in this instead of dynamo
Yes
👍
Btw wt have u attached with the dc motor
Its a capacitor to make the circuit healthy
Where can I get them
Sir, my windmill is moving with speed but the motor is of 9v but can the motor glow a 12v led bulb plss tell me
It will work, but the LED brightness will be low.
Yess sir it worked
Name of motor?
@@diyasfunplay Yes Sir Exactly
Can I use a dc motor for the windmill??
Yes you can.
My motor in 12v does it work
Yes it will work
Sir can you tell me the measurements of card boards that you used?
Sorry that i missed out the dimensions in this project. For the turbine blades you can use a cardboard of size 30X14cm and the tower should be 40 cm tall. You use the other dimensions accordingly. Please let me know if you need any other clarification.
Hi can i adgust the height of cardboard to around 30 to 35 cm
(Tower)
@@tranju1978 Yes, you can. Make sure to reduce the blade lengths accordingly. Else, it will hit the ground.
@@diyasfunplay how long should the turbin blade be
@@mariaelsayed5502 The blade length i had used is around 35cm. Plan accordingly.
Is there an alternative for the rotation knob
Its amazing but add a cm
Sir can you Name the material you had used in it
Items needed for this project:
Cardboard,
Thermocol (only if you want a sturdy base)
hot glue gun
wires,
led bulbs,
switch,
dynamo, generator or dc motor (as you need)
scissors.
Anna that white paper name enna anna
It is called butter paper. You can also use tissue paper.
Name of your glu gun
Themisto
VERY GOOD , BUT ... I have tried with a dc motor and it will not light up unless I spin the blades at almost 1000-RPM using a pc blower , how did You get it right with such a slow turn rate on the shaft ?
You haven't mention measuments of wing.
Length of each blade is around 30 cm
Sir what is the tentative rod size?
Make it at least 10cm longer that the blade, else the blade tips may hit the objects below.
@@diyasfunplay thank you..
hi can u tell how to connect a motor with a battery for this model
Can I make it without any motor?🤔🤨
Hello sir! May I ask what that blue piece at 5:14 is called and where I can get it?
That is a small pulley attached to the motor shaft. That is really not needed for this project. Some dc motors have gear wheels and some have pulleys and others may have wheels too. You can ignore it.
Can u tell me where u got the DC motor pls?
In Amazon
Thanks a lot,sir
What are the lights called and where can I purchase them. Please get back to me as soon as possible.
They are led strip lights. You can get them in electrical shops or online.
Amazon link: amzn.to/449snSc
Thank you
@@diyasfunplaythank you so much
From where you buy cardbord
In local store and sometimes in Amazon.
From where we can get the led lights ??
In electrical shops or online
Hi Guys
What cap value did you use for the LED?
99
Sir you have used how much rpm DC motor?
Somewhere between 10 to 90 rpm. Better is the output
Hope it helps ♥️♥️
Mein kis tarah se aapka dhanyvad Karu
Thank you too...
Plsss tell me how can i run both the windmill and the bulb plss reply me i have to show tomorrow 🙏🙏🙏
If you want to run the wind turbine without an external wind source, you'll have to use a battery to run both the turbine and the light,
Can you tell how to make dynamo
Such as well
Super
What's the use of led bulb
How to make this house
ua-cam.com/video/GtGQB3DvDcg/v-deo.html
what are the measurements??
Sir can windmill blades and stand be available redeemed ?
Sorry, I do not have them now.
It's ok
😀😀😀😀😃😃😃😃😄😆😆😅😂
😜😜😝😝😗☺☺😛😛😛😛☺😗😗☺😚
😗😝😜😔😌😬😍😐😑😶😏😒😬😬😌😔😜
Can you tell me the name of the motor you used to generate electricity
Slow rpm dynamo (can generate power at low speeds)
@@diyasfunplay thankyou
Fun play time ki bacchi tere Jo video hai na sare link mein dal deti hai tu khud dikhaya karna sab kuchh itna information deti baithe ho usse achcha to vah acche to vah Riaz fan play time
Can I get all the materials listed out
Items needed for this project:
Cardboard,
Thermocol (only if you want a sturdy base)
hot glue gun
wires,
led bulbs,
switch,
dynamo, generator or dc motor (as you need)
scissors.
Sir my LED is not working
why?
@@diyasfunplay i did same as you shown in the video. But after switch on the table fan and took the project to front of table fan,Only the motor is running and the light is not working.
Check and make sure that all the connections are correct. Check your generator/dynamo specifications. It should be a "low rpm generator". Normal generators will need more than 1500 rpm to generate electricity. But low rpm generators can generate electricity at a very low rpm. The turbine in my model rotates at around 80- 100 rpm. Only low rpm generators can generate electricity at this rpm. If all connections are correct, then the problem could be with the motor (not being able to generate enough electricity). Also make sure to use a low watt led.
How to make this house
ua-cam.com/video/GtGQB3DvDcg/v-deo.html
Such as well