I have the same device the fan volume is somewhat loud even though the processor temperature is low and I did a good cleaning of the fan and changed the cooling paste for the proctor and the screen card, but unfortunately it is of no use please advise me of the cause of this malfunction
When I connect this all up it appears to trip the ac adapter circuit breaker? as it shuts down. (I tried more than one working adapter, same results). When I take the power input board from the mobo off it does not do that and I get the 19v on the jack. So the mobo is shorting the power out. Is there a component I need to test that may be causing this or is it likely a more major failure?
Your laptop motherboard 19V line short to GND, so you need to inject voltage from external power supply that should be 5amp, then you can find out which parts short.
What if you get 3.3v and 5.1v on those two capacitors? I checked similarly like you checked, what I noticed is that there are two 2.5v capacitor and getting a reading of 0.
Hi, I have this problem on n5110 mb, I change capacitors but no results, 5v and 3v missing...and is not short! On TPS51123 all voltages are like in your video, what ellse can be? tnx
Hi sir.. I have similar problem on dell N 5110. I check power jack voltage it shows 19.5 volts and after that I checked voltage at the same resistor as u told, I found voltage continuously dropping from 19.5 volts to 1 volts. Please tell me why this happen and what should I do now.
Excellent video and your knowledge is impressive. I have a problem with an N5110 that I've not seen before and wondered if you could help. Power button, tested as working, (tried a couple of them) will not turn on the laptop If I unplug the power button ribbon from the mainboard and remove and replace the cmos battery when I plug in the mains charger the laptop will boot and run fine. If I remove the charger to power the laptop off and then replace the power button ribbon cable once again the laptop will not longer start. I have to repeat the procedure and remove the power button again from the laptop, remove and replace the cmos battery and plug in the mains charger without the power button attached for it to boot. There is no visible damage to the pins of the power connector on the board so I'm at a loss. Any help would be welcome and appreciated.
@@Laptop_repair_zone Hi, in this particular laptop is there anything wrong with the screen, on the extreme left up to down screen does not seem normal...my friend's laptop n5110 has this screen issue. Do we need to change screen or the lvds cable?
i have this same model and i have battery iisues i mean it drains quickly and i have to charge it continuously what should i do i have win10 i5 2nd generation install in this model what should i do Please Suggest ne should i replaced my battery or something else i should do
Laptop is powering on through battery. But not powering on through power cable without battery. I checked all voltages as you told with the battery out and power cable plugged. All voltages are correct. Capacitors also gave correct reading. What could be the problem?
@@Laptop_repair_zone Charging section and SIO are showing correct readings. Nothing wrong there. Today after checking. The charging light is blinking. And when the laptop switched on, the charging symbol is also blinking. It is not staying for long.
Greetings friend, I have the same pc. supply voltage is 19.5v that of the first capacitor is 0.752 v , the second of 0.432 v I do not know how to measure the voltages of the next piece, the one at minute 2:24 I don't know exactly what pin. you help me please
i am facing problem on turn off . after press shutdown, it just close the lcd but still power button is on. i have to press and hold on the power button for complete shutdown. please advise. i am really worried due to this issue,
Laptop Repair Zone when i power on the lap it is black screen like the one shown in end of your video at 6:18 in yours say connect to 85w charger in my message say connect with 135w charger and the lap is toooooo slow
Hi, I have Inspiron N5010 and it got dead during BIOS update from A12 to A15. No power LED nothing just dead. Where to look for the problem BIOS or Power supply? Laptop is dead and no LED or Power button response after plugged in. Adaptor is working. Any help appretiated.
Laptop and it's Fan starts after clicking Power button and after 5sec, Fan stops but Light of Power button still On.. After 10sec, Beep sound starts.. Whats the Issue..?
Sir How do you be sure!!..i have a 9104p , 19v is ok ,no 3valw/5valw , no short to ground in the rail of 19v and the rail of 3/5 valw...change the Ic ( RT8205LZQW) with a sure one who works perfect at other motherboard same problem ! i think that all the V is Ok on this IC ,entrip 1 and 2 = 1.2 and 1.3 v....vreg 3 = 3.3v and vreg 5 = 4.5 v! ...Vin =19 v...en = 3v....i take this result with multimeter on OHM mode for the 2 solid capacitor after the coil , rail 3v = 122 ohm , rail 5v = 82 ohm....sir waht else to chek!!..thx
Hi bro, Does this power board (dq15dn15) generate 19v voltage when not connected to the mainboard? I have a dell i5 with crazy voltages on the power board and I don't know if it's a problem on the power board or if it's a problem on the mainboard! I have already removed several components and the problem persists. i.postimg.cc/j2p5Yx1v/6874684-jpg-baa0f434a5ba78916708c1a5a0d9b592.jpg i.postimg.cc/T2FhD0Pm/Sem-t-tulo.jpg
i'll make video soon how to find short and leakege capacitor on matherboard.
Same issue how much cost in rupees
Was that cap shot ? How did you pin point that cap cause 3&5V IC to not out put the Voltage
Beautiful video🎥 Bro👌👍🙏🙏
How to buy this Capacitor
Please Help me🙏🙏
I have the same device the fan volume is somewhat loud even though the processor temperature is low and I did a good cleaning of the fan and changed the cooling paste for the proctor and the screen card, but unfortunately it is of no use please advise me of the cause of this malfunction
Hi..sir if u don't mind...
Why are you changing capacitor...anad
How to guess 🤔 this problem 🤝
When I connect this all up it appears to trip the ac adapter circuit breaker? as it shuts down. (I tried more than one working adapter, same results). When I take the power input board from the mobo off it does not do that and I get the 19v on the jack. So the mobo is shorting the power out. Is there a component I need to test that may be causing this or is it likely a more major failure?
Your laptop motherboard 19V line short to GND, so you need to inject voltage from external power supply that should be 5amp, then you can find out which parts short.
good video thank you for sharing. i fixed my laptop
What if you get 3.3v and 5.1v on those two capacitors? I checked similarly like you checked, what I noticed is that there are two 2.5v capacitor and getting a reading of 0.
Check step by step as I check.thanks.
@@Laptop_repair_zone that is what I did although the power ic part can be a bit trickier to exactly touch the right pins. Thanks.
Hi, I have this problem on n5110 mb, I change capacitors but no results, 5v and 3v missing...and is not short! On TPS51123 all voltages are like in your video, what ellse can be? tnx
Thanks for your comment.please change TPS51123.
My dell N5110 has pch short circuited!!!Can I replace Pch?
Thanks for your comment. yes you can replace.
Hi sir.. I have similar problem on dell N 5110. I check power jack voltage it shows 19.5 volts and after that I checked voltage at the same resistor as u told, I found voltage continuously dropping from 19.5 volts to 1 volts. Please tell me why this happen and what should I do now.
GAURAV PURWAR 19.5 volt rail maybe short to GND try to find short components thanks
Excellent video and your knowledge is impressive.
I have a problem with an N5110 that I've not seen before and wondered if you could help.
Power button, tested as working, (tried a couple of them) will not turn on the laptop
If I unplug the power button ribbon from the mainboard and remove and replace the cmos battery when I plug in the mains charger the laptop will boot and run fine.
If I remove the charger to power the laptop off and then replace the power button ribbon cable once again the laptop will not longer start. I have to repeat the procedure and remove the power button again from the laptop, remove and replace the cmos battery and plug in the mains charger without the power button attached for it to boot.
There is no visible damage to the pins of the power connector on the board so I'm at a loss. Any help would be welcome and appreciated.
lee reflow the PCH then try,thanks.
Hi was that PCH problem ? i would be appreciated if you share your experience with this wired case :)
@@Laptop_repair_zone Hi, in this particular laptop is there anything wrong with the screen, on the extreme left up to down screen does not seem normal...my friend's laptop n5110 has this screen issue. Do we need to change screen or the lvds cable?
Same issue How much it will cost to repair????
i have this same model and i have battery iisues i mean it drains quickly and i have to charge it continuously what should i do i have win10 i5 2nd generation install in this model what should i do Please Suggest ne should i replaced my battery or something else i should do
Hi, my problem is, my system showing the screen like BOOTMGR is missing press ctrl+Alt+Del to restart
But it is not working. So what can I do?
byella dilip kumar thanks for your comment. Please reinstall operating system.
Laptop is powering on through battery. But not powering on through power cable without battery. I checked all voltages as you told with the battery out and power cable plugged. All voltages are correct. Capacitors also gave correct reading. What could be the problem?
Thanks for your comment. Please check charging section and SIO.
@@Laptop_repair_zone Charging section and SIO are showing correct readings. Nothing wrong there. Today after checking. The charging light is blinking. And when the laptop switched on, the charging symbol is also blinking. It is not staying for long.
Chech if the 3rd pin of charging port is connected. Because of the design this 3rd data pin often get disconnected over time
Sir pin number 18 enable voltage is not present so what can i do for that salutation
Thanks for your comment. Please follow the Schematic diagram.
Sir hamara leptop dell Inspiron n 5030 on nahi ho raha hai please help me
Greetings friend, I have the same pc.
supply voltage is 19.5v
that of the first capacitor is 0.752 v
, the second of 0.432 v
I do not know how to measure the voltages of the next piece, the one at minute 2:24
I don't know exactly what pin.
you help me please
Thanks for your comment, change 3v and 5v IC
i am facing problem on turn off . after press shutdown, it just close the lcd but still power button is on. i have to press and hold on the power button for complete shutdown. please advise. i am really worried due to this issue,
You didn't fix it? Where is voltage protection diode on the n5100 ?
Please write ✍🏾 a step by guide on how to do this please 🙏🏾
I have Dell Inspiron n5110 and I want to play GTA 5 in my laptop.please make a gaming PC build video for Dell Inspiron n5110 laptop
Thanks for your comment.
in my n5110 the battery not charged/not detected and give me the massage in black screen i need to connect to 135 w charger what shall i do
Ehab Mohamed what massage show in your screen?
Laptop Repair Zone when i power on the lap it is black screen like the one shown in end of your video at 6:18 in yours say connect to 85w charger in my message say connect with 135w charger and the lap is toooooo slow
It’s motherboard issue you need to check motherboard charging Port.
Laptop Repair Zone how can i check it. And you mean heck power board only or all motherboard
Hi, I have Inspiron N5010 and it got dead during BIOS update from A12 to A15. No power LED nothing just dead. Where to look for the problem BIOS or Power supply? Laptop is dead and no LED or Power button response after plugged in. Adaptor is working. Any help appretiated.
Rizwan Naik your location please.
@@Laptop_repair_zone mumbai. But i am tech. I can try to solve myselfe. Need guidance.
sorry bro my location is dhaka bangladesh.
remove bios ic than flash it
@@GMurali26 how to getbto bios ic. Any directions?
Laptop and it's Fan starts after clicking Power button and after 5sec, Fan stops but Light of Power button still On..
After 10sec, Beep sound starts..
Whats the Issue..?
Thanks for your comment, how many beeps?
@@Laptop_repair_zone Beeps continues until we switch off manually
I have same problm but there is no ENC voltage
Thanks for your comment.
How check this modle white screen??
Chetan Darji check lcdvcc 3.3v parts number U4901 thanks.
ayse kaise change kiya aapne bataya he nahi ke kharabi nikli kaise
great fix thank you very much for sharing!
really !! that's awesome; good job
Nice Ji
what is model no of 3v &5v power IC
Nambi Rmk you can use TPS51125
Sir my volt power ic heat too much and 3 v n 5 v also not show kindly give me solution plzzz
Thanks for your comment.1st check 3v LDO 5v LDO is short or not.
leakage capacitor.
Sir How do you be sure!!..i have a 9104p , 19v is ok ,no 3valw/5valw , no short to ground in the rail of 19v and the rail of 3/5 valw...change the Ic ( RT8205LZQW) with a sure one who works perfect at other motherboard same problem ! i think that all the V is Ok on this IC ,entrip 1 and 2 = 1.2 and 1.3 v....vreg 3 = 3.3v and vreg 5 = 4.5 v! ...Vin =19 v...en = 3v....i take this result with multimeter on OHM mode for the 2 solid capacitor after the coil , rail 3v = 122 ohm , rail 5v = 82 ohm....sir waht else to chek!!..thx
Change 2 solid capacitor and then check.thanks
You can use smd 330uf capacitor?
I do , but same issue! no 3 /5 valw !
Bro my laptop turns off with a click and using it for 30 or 15 mins, I don't think it is overheating please help
How much repair cost for this issue in rupees tell me
Thanks for your comment, i have no idea how much cost will be you there, im from dhaka bangladesh.
@@Laptop_repair_zone u can tell me in ur currency, I'll convert in my currency so that I can negotiate to repair.
Red light is blinking 4 times and my laptop is not being on. Please help me
Thanks for your comment,motherboard problem.
Good job 👍
Thank you! Cheers!
Hi bro, Does this power board (dq15dn15) generate 19v voltage when not connected to the mainboard? I have a dell i5 with crazy voltages on the power board and I don't know if it's a problem on the power board or if it's a problem on the mainboard! I have already removed several components and the problem persists.
i.postimg.cc/j2p5Yx1v/6874684-jpg-baa0f434a5ba78916708c1a5a0d9b592.jpg
i.postimg.cc/T2FhD0Pm/Sem-t-tulo.jpg
Same problem 😢 price?
Thanks for your comment...
Sir do more videos ❤️
Dell inspiron 3521 not turn ing on pls upload video
MOHAMMED NAJEEBUDDIN I already uploaded please check in my videos.
@@Laptop_repair_zone thanks a lot
Hi lwant to learn
good job
Thank you
Thanks for your comment,
thanx sir ❤️
googd master
Love you
Mera dell laptop charge ho rha hai but on nhi ho rha hai kya karu.. 7353022456
thanks for your comment, if you are a technician than take out the motherboard and check all the require voltage step by step.
@@Laptop_repair_zone m not a technicians plz send ur no.
good job
googd master
thanks for your comment.