50cc moped | Conversion - Electronic ignition 12Volt | Kokusan op een Kreidler brommer

In this series of upcoming videos I will show you the restoration process of my new bike.
Some details of the bike:
Brand - Kreidler Florett (RS)
Year - 1977
Engine - 2 stroke | 50 cc
Gearbox - direct | 5 speed (gears)
Modifications which needs to be done:
- Changing the ignition system, from a conventional 6V system to an 12V system. (Shown in this video )
- Replacing the wheel bearing (Front one done, rear wheel aswell)
- Rewire the whole bike with a new wiring system (Done)
- Repairing the rear drum brake (Sorted)
- Refreshing the oil in the front suspension fork. (Overhaul of the complete fork is shown in this video)
- Renewing the gearbox oil
- Renewing the rear tyre (Sorted)
- Etc, etc, etc.
I have a Patreon page, consider checking it out:
www.patreon.co...
Video gear used:
- Sony DSC-WX500
- Vanguard tripod
- This video was created with iMovie -
All the best,
Jan

[@johnfry9010]

I still have my old 70's 400cc Jawa CZ that I rode when I was young , it was a challenge to keep in tune with the dual point ignition , that electronic setup is the ticket !

[@JanDootjes]

Hey John!
What a beast that must be, 400cc jeez!
Electronic ignition is the way to go nowadays :) Especially when you're about to make a lot of and long (hopefully) trouble free rides.
All the best, from Holland!
Jan

[@jgdsfds]

Why everyone use HPI, even pvl rotor but i dont see anyone using analog selettra ignition?

[@MrJackiyi1]

Hey there, can you tell me which one of the marks from the baseplate is the right one to line it up with the pole wheel?

[@paulolemos7032]

Very good

[@triumphdollysprint]

hey mate, thanks for the video, very helpful. do you think the same method would work with a piaggio si 50cc motor? im struggling to find an off the shelf 12v kits where i am...

[@ag2938]

Wieviel Watt Leistung hat die neue 12 Volt Zündungsanlage?

[@JanDootjes]

Moet je even googelen

[@SunnyHolly2022]

Kokusan zB hat ca 70-80 Watt, HPI Innenrotor hat Lichtspule mit 60 Watt

[@DimitrisEuaggelia]

Hi man. What about the cdi after 3 years,
Does it still work fine?

[@JanDootjes]

I sold the bike two years ago 😅

[@Helikopterpop]

What is the benefits of kokusan and which wattage is best for a mustang mamba moped?

[@ag2938]

12 Volt, immer mein Traum, hätte damals so gerne ein H4 Scheinwerfereinsatz gehabt, war zu dieser Zeit das Nonplusultra (1976)an Licht, aber nicht zu Realisieren .

[@JanDootjes]

Geen idee waar je het over hebt

[@ag2938]

Danke

[@erculatif2306]

cool very nice man :)

[@JanDootjes]

Thanks for the comment!

[@intelmossadcabangdjakarta7893]

what kind of a complete set of new magnetto you used？ is the new rotor magnetto inner diameter are exactly same with it’s origin kreidler？tx

[@schirmeyerb]

Why with the turbine.....there is not exterior box....? Do you have put a little batterie..? I wait an answer here please..please

[@schirmeyerb]

Des gens dise que le KENNEDY ..est plus facile à installer..et marche à tout les coups.........mais il est 3× plus chère...neanmoin tes vidéos sont tous EXTRA

[@Helikopterpop]

Why retard 1,2mm? Some say 1,8mm? What is the best value? The ealier you get the timing, the more the compression builds up right?

[@tim9464]

Because if your cilinder runs above 12k rpm there is a chance it will blow a hole in your piston if the timing is at 1.8mm

[@amyandbillyradcliffe2751]

hi what manufacturer is it and nice job

[@Youri.46]

Dankje, erg hulpzaam. Moet mijn kokusan ook afstellen

[@JanDootjes]

Goed om te horen dat het je helpt Youri! Succes met afstellen :)