@rcnightmare Just took it apart, the spring was lose and the one way bearing had grit on it, give both parts a wipe and now have the tedious job of getting it back in the case XD thanks for your help
What I use to replace the pull start string is window blinds string the good ones,! Some people throw them out so free to me .,,,!! The stuff is so strong I have never had it brake as long as you have good knots on the ends no problem, and my engine has high compression being a racing engine.
I have a HPI truggy, had it 3 weeks, took it out 3 times and then the pullstart went slack, on the 3rd run, so it doesnt retract into the pullstart case, any ideas why? p.s. I never pulled it more than 30cm btw :) Cheers
It is just not that easy I tried to do this with my exceed rc 1/8 .28 short course truck please don't try this unless you don't mind having an aneurysm
@yoyoairsoft1411564 why don't you messure up your broken cord for the length? even if it broken you can still put the 2 pieces behind iech other and messure it up.
@keith179150 it took like 3 shoots cuz the thing kept exploding! That said some people don't mind it, I am with ya though...I be ordering a new one in the event it breaks :)
the part when you put in ..you pull out the winding metal plate but the video was not able to capture how you plugged it in. that was the most important part..i don't know what you did there coz it was not shown.
I also struggled with this problem. Solved it by winding up the spring as tiny as possible. Than use pliers to hold the barely end of the spring and the beginning of the spring. Do not loose grip, otherwise it wil unwind itself again. Than put it in the housing and slowly release the pliers. Now the spring will unwind on the housing.
easiest way is to wind up the spring after installing the spool in the housing since you can pull the spring through the housing and wind it into the housing.
Dude what you did in 13:11 took me 10 hours, the 30 seconds it took you to tighten the chord took me 5 hours. Cut my finger open and caused a large amount of depression, ps i still cant do it. Fuck this demo
1st most of us would have liked to see how it comes apart. 2nd close-ups to view detail would be nice. 3rd stop with the twitchy hands and show what you're talking about. finally it was painful to watch too slow had to fast forward to the important bits only to find twitchy hand syndrome failing to show detail. Anyway you tried, thanks.
you don't like his vidio, you must be stupid, you can change the channel. very interesting, don't mind them, but keep the camera so we may see better. God bless
MrZoomey probably wayyy tooo lateee but if you want you can super glue the hook thing into the place where it grabs it so you can spin the metal inside easier
To all nitro rc enthusiasm if your pull start should come apart just buy a new one it'll piss you off to the point where you wouldn't want to see another nitro rc car . The rc world should stop making pull starts along with body clips they are the worst thing about this hobby
i agree with you , but i'm fuckin sick of the hobby shop charging a fortune for their dodgy shit that can be fixed in no time , it's so wasteful , their attitude of disposing of things and buying more . other than flimsy quality nitro cars are fun .
You need to get more straight to the point cause you took forever to get started seriously dude most people can see the parts already so they know what it is if they at this stage
I was fixing to give up and buy a new one till I found your video after watching it I got it on the first try ..Thank you
you suck lol😂😚
@surfboyrio thanks for the kind words!
@rcnightmare Just took it apart, the spring was lose and the one way bearing had grit on it, give both parts a wipe and now have the tedious job of getting it back in the case XD thanks for your help
the amount of times ive had to do this is mad!
17 to be precise, but on 3 pullstarts!!!
What I use to replace the pull start string is window blinds string the good ones,! Some people throw them out so free to me .,,,!! The stuff is so strong I have never had it brake as long as you have good knots on the ends no problem, and my engine has high compression being a racing engine.
can you explain more tips on how not to have the coil spring shoot out and how to tuck the coil in while having it hook properly.
**wipes tears and blood off keyboard**
Thank you!
I have a volcano s30 gas powered 4x4 truck. Rope snapped when trying to start. How Can I make this work again?
Great tutorial of the table top.
Thanks. Most practical method i found on youtube, i finally did,
@NirvanaRox4Eva it may have come loose inside, I think just taking it apart and rewinding there might be a tangle too
@rcnightmare which way does the one way bearing go in by the way Xd i forgot which way i took it out :P
at 8:58 you didn't show us how to attach it .... this is some bullshit
Awesome I did it. Thanks.
u make it look so easy GRRRRR lol my spring is huge in mine, an its a bitch to wind, pisses me off SO BAD LOL
I have a HPI truggy, had it 3 weeks, took it out 3 times and then the pullstart went slack, on the 3rd run, so it doesnt retract into the pullstart case, any ideas why?
p.s. I never pulled it more than 30cm btw :)
Cheers
It is just not that easy I tried to do this with my exceed rc 1/8 .28 short course truck please don't try this unless you don't mind having an aneurysm
I know bro I'm gonna kill it !! same truck!!😂
@@glenhuson15i doing this on my os18tm IM GONNA FUcKInG THROW THIS THING
Haha. Not to mention diced fingers , but I saved a very nice vintage engine doing this , took hours.
thanks you saved my day
@mullimaddness no worried...its a pain....
you don't show the most interesting part starting 8'38 to 8'58
@yoyoairsoft1411564
why don't you messure up your broken cord for the length? even if it broken you can still put the 2 pieces behind iech other and messure it up.
some on please help when i tighten my pull start screws it does not recoil but when i leave then loose the recoils please help
@official... I think your metal strap/spring is detached.
@keith179150 it took like 3 shoots cuz the thing kept exploding!
That said some people don't mind it, I am with ya though...I be ordering a new one in the event it breaks :)
Thank you it help out
i have a carson 1:10 buggy i think it works!
Where can I take my Rc Car to get it put back together?
Ginge Cast a hobby shop
the part when you put in ..you pull out the winding metal plate but the video was not able to capture how you plugged it in.
that was the most important part..i don't know what you did there coz it was not shown.
the coil spring is ALOT of fun. it takes forever so u get nonstop "exitement" for days to come. yay.
fuq my life
ive been having a blast with my spring. I love my spring.
thanks , very much , like is the channel youtube :D
When I pull on the cord it doesn't rewind?
Airgun Cole try oiling or greasing the spring
Ok this is making me what to leave this hobby
How the f--/:$&ck you get the spring in the housing this is the third day I'm trying I can't get it in
I also struggled with this problem. Solved it by winding up the spring as tiny as possible. Than use pliers to hold the barely end of the spring and the beginning of the spring. Do not loose grip, otherwise it wil unwind itself again. Than put it in the housing and slowly release the pliers. Now the spring will unwind on the housing.
easiest way is to wind up the spring after installing the spool in the housing since you can pull the spring through the housing and wind it into the housing.
Dude what you did in 13:11 took me 10 hours, the 30 seconds it took you to tighten the chord took me 5 hours. Cut my finger open and caused a large amount of depression, ps i still cant do it. Fuck
this demo
the part you are looking for is 3:50 the other part your looking for is at #hobbyshop
i did it the cord went back in screwed onto my car and it wouldnt go back in
jesus get on with it
1st most of us would have liked to see how it comes apart. 2nd close-ups to view detail would be nice. 3rd stop with the twitchy hands and show what you're talking about. finally it was painful to watch too slow had to fast forward to the important bits only to find twitchy hand syndrome failing to show detail. Anyway you tried, thanks.
u skipped the most important part. godamn it why?
you don't like his vidio, you must be stupid, you can change the channel. very interesting, don't mind them, but keep the camera so we may see better. God bless
@mullimaddness that wasn't nice...
MY ONE KEEPS SHOOTING OUT
this fukin spring thing is pissin me off
MrZoomey probably wayyy tooo lateee but if you want you can super glue the hook thing into the place where it grabs it so you can spin the metal inside easier
0:20 to skip ads
hahah pullstarts r a pain in the ass, it easier just to buy a new one, i've tried repairing em before, it takes forever
@Gopedrider
If you go to my page in about 10 hrs I'll have a video up
To all nitro rc enthusiasm if your pull start should come apart just buy a new one it'll piss you off to the point where you wouldn't want to see another nitro rc car . The rc world should stop making pull starts along with body clips they are the worst thing about this hobby
i agree with you , but i'm fuckin sick of the hobby shop charging a fortune for their dodgy shit that can be fixed in no time , it's so wasteful , their attitude of disposing of things and buying more . other than flimsy quality nitro cars are fun .
You need to get more straight to the point cause you took forever to get started seriously dude most people can see the parts already so they know what it is if they at this stage
Your intro music is awful...but great tutorial...
This way ruined my pull start !!!
rEALLY ISNT EASY I MIGHT JUST HAVE TO PAY THE £30
"As you can see" yea fuck all...
to much info, get to the point
Holy crap I give up this video is so slow
would have been nice to actually see what hes talking about.... what a waste of 10mins.
Painfully slow...