Just a heads up: Later versions of the CR-6 SE (Don't know about the Max) might have came with a Creality Era V1.1.0.3 motherboard. The ID silkscreen will be smack in the middle if you have one of these Creality Era boards. This is going to be functionally equivalent to 4.5.3, so follow those instructions. Just wanted to put that out there in case you were confused like me when trying to figure out what firmware to go with. Happy printing!
Great guide and video. Followed the steps and it worked first time. Took your advice and changed the name to firmware1 straight away. Brilliant. Levelling the bed is much more informative, showing you the calibration it makes for the mesh. Love it. Thanks dude.
Thanks for this video. Really good job in breaking it down step-by-step and covering all the need-to-know points that veterans might be aware of, but newbies like myself have no clue about. Really great. Your review on the CR^SE was also part of what led me to get one in the first place, so thanks for that as well. :)
Love the community firmware. Been using it since Christmas. AM eagerly awaiting Release 6. Sebastiaan and team have done an outstanding job when compared to Creality's stock version.
A great video! Just a note... I believe that the SD card for the MB firmware should also be formatted the same way as the mini SD card used for the screen (no bigger than 8MB, FAT 32, and 4096 cluster size). In other words, both SD cards should be the same size and formatted the same way.
Just updated to 6.1. Huge thank you for this. I too had to change the file to 1.bin but after that, it worked like a champ. Love the update as I've got a fairly uneven bed but the new update seems to be able to overcome that.
just upgraded my CR6-se today. And love the new interface. Thanks for the step by step video. you rock @the Edge of Tech!!!!!!!! can't wait for version 6. couldn't log in to the discord link. Again thanks
Thank you so much for this video! I just dusted off my CR6 SE after a couple years of sitting idle. Prints kept stalling, and I read there were some SD card reader issues. I updated to the latest community firmware per your perfect instructions, and I'm printing again! Thank You!
Excellent video! Made it easy to upgrade my (Kickstarter, received in October) v4.5.2 motherboard and v1.0.2 screen firmware. Was previously having a lot of issues (stringing/etc) with the stock MB/TFT firmware and was hesitant about trying the Community Edition firmware but you sold me. Now running test prints (first two tests look good). Thanks for your time and energy!
I was an early bird on this kickstarted and its been sitting in the box since I got it. I was first 300 and one of the last few to receive mine. Purchased the upgraded CR Era board a couple months back and am tackling this now before I even try to print!
Hey thanks for this guide dude. I just updated to the 6.1. I was avoiding the community f/w, but after watching this, I went for it. Great results. Worked just as you said. Smooth sailing, renamed the mainboard file, used a 2gb SD formatted as you explain. Great job!
They haven't really released the display firmware, but the DWIN tools contain the ability to reverse engineer the project files from the display firmware binaries.
If it weren't for this video, I have no doubt I would have been too intimidated to try the Community Firmware upgrade on my own. Thanks to this video it worked like a charm...great video!
7/26/2022 just updated my cr6-se and it works fantastic ! havent used it for a few years so long overdue but looking forward to trying some prints again. Big thanks for this video !
Thank you so much! This was an easy guide to follow even with a newer version for a newbie like me. Again thank you so much, I can't wait to get back to printing.
Thank you very much for the video!. It helped me a lot. Very good firmware development. I recommend it, excellent work by Sebastian's team. Now the printer has leveled up and it is excellent. Thank you very much again for teaching how to install this fabulous Firmware. Greetings!.
Thanks. Just worked perfectly. Had to format the micro SD on a Mac in terminal using the instructions in the readme file. Put on the latest version and up an printing in about 30 min.
Haven't gone to the community FW yet, but when I do, was your screen timing out after only a few seconds after you updated to v6? If so, that'll get annoying really fast.
Just installed the community firmware, everything works great. One thing you didn't mention in your video ( but it is mentioned in the read me files ), you screen needs to say " T5L1 DGUS2 V3.5 2020.07.30 " at the very top while / after doing the screen firmware ( that red text ) . If it is a lower or higher V number, your screen will be blank after taking out the micro sd card. If this is the case, simply add the files from the "CR-6 kernel upgrade" map to the "DWIN_SET" map and start over again with the screen firmware. Everything should be fine after that.
Really great video! Thank you! But i was wondering about the SD card (not the micro SD) can it be taken out to transfer prints on? Or does it need to be inserted at all times now with the firmware? :O
Hey Jim, I followed this video and upgraded my firmware to the Community version.......LOVE IT! Now I have a question since new versions have come out. Do I have to flash both the screen and firmware or can I just upgrade the firmware to the new version?
Great thank you so much for you easy to follow explanation thanks also to the community, my printer works great now had issues with leveling but all fixed, A************ to all
Do you have a video that gives step by step to install a BMG on to the cr6 se? This video was very clear adn straight forward so keep up the great work.
Hello, I don't information on the compatibility with what it seems to be latest motherboard of the CR-6 SE, the "CR-ERA_V1.1.0.3" version. Would the firmware for the 4.5.3 version compatible ?
I bought the cr6se because it was only 20% more than the E3v2 in stores around my country. Seemed like it would be worth it for the extra features, and hoping that there are no lingering magic smoke issues on whatever ones they had in stock
Jim,, Good video. I no longer have mine but will pass this on. Does this provide new functions / features? This would be easier if the display Micro SD card could be accessed with out removing the screen
Thanks! Ya, it's much better than my stock firmware! You can see a list github.com/CR6Community/Marlin/releases/tag/v2.0.7.3-cr6-community-release-5-beta the changes here!
@@TheEdgeofTech Thanks for the link. It seems like a lot of improvements have been made. This is one reason that I gave the printer to my neighbor, it was just too limited and very little upgrade options
I went to print something and the screen is just a blank screen. I tried to reflash the screen and it does get any further then 3 lines and I left it to see if it's going to finish and after a couple hours was still stuck at that point. I'm not sure what to do from here, can you help me out?
I know this video is a bit old, but does anyone have directions on how to change the firmware size of the bed on my CR6SE? I did a change and my bed is now limited narrower by direct drive mount.
I have a CR-6SE and its been great so far, but I am starting to notice the firmware holding me back when compared to my manually compiled firmware of my Ender 3 Pro. This video is a year old now, so I was hoping you could give a little direction on where I can find the latest firmware for my CR-6 and ask if you recommend I upgrade?
I've tried many times to flash my TFT I got mine with a motherboard that says CR -ERA 1.1.0.3, I've read I need to use the CF6.1-Final-cr6-se-v4.5.3-mb-2021-06-04-16-53 but after flashing it multiple times and following the instructions here it still doesn't work. When I boot up it says creality community firmware in the loading screen but it just stays there. Any advice or something else I could try? Thank you!
ive got a question. No one seems to want to provide a proper explanation as to why the nozzle temp is set to 0 when leveling the bed as the z axis goes down. wouldnt you be getting inaccurate measurements of the bed if youre probing all 16 points at varying different temperatures? so one point can probe at 149 then the next gets probed at 140 and so on.
Hi! I've just ran this procedure in my printer (all installed without issues) and it failes to heat up afterwards, so it´s not even able to do the bed leveling. Any idea what might be going wrong? Many thanks!
Bro im not sure if i want to do this now that i already have bed issue, my bed is moving slowly some times and so the nozzle and the bed are never centred
What are the biggest differences/significant advantages to use the community firmwares? I am struggling to find two SD card types to flash the machine, and am wondering whether it is worth the effort…
I followed the steps including copying the kernel upgrade files into DWIN_SET folder. My screen gives me the updates Community Edition splash screen, beeps once and freezes at 100%.
@@Wicky_FPV Its been awhile so I forget exactly how I got it to work. I know once I bought a new SD card with the correct specs I was able to get it to work. Best of luck!
That's what I was hoping to understand. Is there a reason I want this over Marlin? Edit: this is from their github This Marlin fork has the goal of cleaning-up the source code changes for the CR-6 so it can be merged upstream. We also want to extend the functionality to make it fully functional So maybe Marlin doesn't currently have support and they are working on fixing that and then merging with the main branch of Marlin.
Cura "Pause" and "Filament Change" scripts now work. Z-height offset is now adjustable to 0.01mm, on the fly flow rate, and better bed leveling are just a few of the features I use and love.
I just upgraded firmware to 6.1, and no matter what I do, auto-leveling does nothing. It heats up. homes and then just sits there. It doesnt level. Couldn't find anything else on the github about others having this issue.
Try running the firmware again, and make sure it's the newest version. Just out of curiosity, what's it heats up and it's just sitting there, what happens if you turn the nozzle temperature down a degree or two. Does it start?
@@TheEdgeofTech I tried launching the firmware on the main sd card 2 or 3 times. Still does the same thing. It heats to 145 for hotend and 50 for the bed. I can't change the temp of anything, I can't even hit back, as it just says " it needs to finish up "
Hi there, thank you for the video. I have updated my Printer and It works great but i started noticing that the printer is taking longer, way longer than before while printing the same objects.
What do I do if I do not have any display on my touch screen? There is nothing there and it won't turn on. Just a fan and a flashing light in the extruder.
JIm, question. I have updated per your instructions and I believe firmware is ok with version 6, but problem when the printer is homing the nozzle gets press on the glass plate. NOTE:I have done reset factory. HELP HELP. I tried to install old firmware and problem still there, I have to assume all the zoning is bad ALL help is really apreciated
OK Stupid question. I'm trying to figure out which motherboard I have but there's no number on board. I looked in the info and have the 2.0.1.9, so I'm holding off until I get figure out these questions. I hope you can help me.
Hi not good the new update does not work the back button does not display the time properly and there is still a problem with the display. :( Where can I find the pre-update ??? creality cr6 se. Which is good for eliminating the initial temperature drop in printing
Hello guys I had a problem with the installation and the touch doesn't work anymore. I tried to go back to the original software and it doesn't work either. could you help me?😭
I just tried this and the screen totally rejected the update. I have a new printer with the v1.1.0.3-ER mainboard. I followed these instructions and the included the Kernel update files for the screen as the text file instructs and the screen booted as normal. I rebooted multiple times and it didn't read the card. . When I went to the "Info" tab, it had no version. I removed the card and rebooted the printer and it was as if nothing happened. I wonder if there's been a revision to the screen firmware since the most recent update.
@@TheEdgeofTech The issue was the printer's screen didn't like my 16GB micro SD card. I formatted a 32GB as a 16GB and it recognized it. I'm all good now. Thank you for the awesome videos and content.
My CR-6 SE would not level anymore. So I reloaded the release 6 software and still had the same problem. Do you have any ideas that might help? I reloaded the beta 5 version and it works, but not as good as the latest. Any ideas?
Bonjour à Tous ! Pouvez vous me confirmer qu'en exécutant la mise à jour pas à pas du Firmware communautaire, cela fonctionne très correctement en date du 31 mai 2022 ? Et juste une petite remarque sur le gars de la vidéo, euh sans être méchant mais plutôt méfiant, ce gars là ne m'inspire pas vraiment confiance, alors si il y a des gens qui ont installés cette fameuse MAJ, je souhaiterai cordialement avoir des retours positifs avant de risquer de mettre ma machine en carafe, par avance merci! Note: j'en suis a ma deuxième imprimante, la précédente qui fonctionne toujours parfaitement, mais manquant un peu de précision et d'options je trouve (Elegoo Neptune 2S), je souhaite me diriger vers un Upgrade ou plutôt ici vers un changement complet du Firmware, ceci en ayant auparavant bien maitrisé La CR-SE fonctionnant sous Cura, donc c'est une évolution sage et maitrisée j'espère.. merci à tous de vos retours (même si je sais que ce n'est pas la place idéale pour ce genre de demande
Great video. Unfortunately, after flashing everything, it now drives the head into the build plate when it auto-homes. I've verified the motherboard version and firmware versions (I'm aware that is you install new version firmware on old version MB it does this, but I've verified I have new MB version). No idea.
Well I used the same cards as you did and when updating the display, it jumps right to tge normal screen. Before you ask, I did everything you did. Any thoughts?
My printer beeps a bunch when I boot it up now, the blue light is blinking and doesn’t stop, and I see no firmware version listed on the menu. Also , no files appear on the file select. Can you please help me fix this?
Just a heads up: Later versions of the CR-6 SE (Don't know about the Max) might have came with a Creality Era V1.1.0.3 motherboard. The ID silkscreen will be smack in the middle if you have one of these Creality Era boards. This is going to be functionally equivalent to 4.5.3, so follow those instructions.
Just wanted to put that out there in case you were confused like me when trying to figure out what firmware to go with. Happy printing!
Awesome video - was worried it would be very difficult but you made it easy - the screen part was the hardest. Thank you!
I have had a tremendous experience with the community firmware.I have been following Discord and they are working on 6.1! Just amazing!
I agree! It's been awesome to me as well!
Thank you - pitched at exactly the right level, clear, concise and worked first time. Great work!
Great guide and video. Followed the steps and it worked first time. Took your advice and changed the name to firmware1 straight away. Brilliant. Levelling the bed is much more informative, showing you the calibration it makes for the mesh. Love it. Thanks dude.
Thanks for this video. Really good job in breaking it down step-by-step and covering all the need-to-know points that veterans might be aware of, but newbies like myself have no clue about. Really great. Your review on the CR^SE was also part of what led me to get one in the first place, so thanks for that as well. :)
Love the community firmware. Been using it since Christmas. AM eagerly awaiting Release 6. Sebastiaan and team have done an outstanding job when compared to Creality's stock version.
Awesome!!
A great video! Just a note... I believe that the SD card for the MB firmware should also be formatted the same way as the mini SD card used for the screen (no bigger than 8MB, FAT 32, and 4096 cluster size). In other words, both SD cards should be the same size and formatted the same way.
Just updated to 6.1. Huge thank you for this. I too had to change the file to 1.bin but after that, it worked like a champ. Love the update as I've got a fairly uneven bed but the new update seems to be able to overcome that.
just upgraded my CR6-se today. And love the new interface. Thanks for the step by step video. you rock @the Edge of Tech!!!!!!!! can't wait for version 6. couldn't log in to the discord link. Again thanks
Thank you so much for this video! I just dusted off my CR6 SE after a couple years of sitting idle. Prints kept stalling, and I read there were some SD card reader issues. I updated to the latest community firmware per your perfect instructions, and I'm printing again! Thank You!
Excellent video! Made it easy to upgrade my (Kickstarter, received in October) v4.5.2 motherboard and v1.0.2 screen firmware. Was previously having a lot of issues (stringing/etc) with the stock MB/TFT firmware and was hesitant about trying the Community Edition firmware but you sold me. Now running test prints (first two tests look good). Thanks for your time and energy!
I was an early bird on this kickstarted and its been sitting in the box since I got it. I was first 300 and one of the last few to receive mine. Purchased the upgraded CR Era board a couple months back and am tackling this now before I even try to print!
Thank you. I found the community firmware page on my own, but the wall of text was daunting. Your vid helped me figure out what to do.
Hey thanks for this guide dude. I just updated to the 6.1. I was avoiding the community f/w, but after watching this, I went for it. Great results. Worked just as you said. Smooth sailing, renamed the mainboard file, used a 2gb SD formatted as you explain. Great job!
Interesting upgrade.
Nice to hear that Creativity have released the display FW.
Thanks for sharing your experience with all of us 👍😊
Thanks for watching!
They haven't really released the display firmware, but the DWIN tools contain the ability to reverse engineer the project files from the display firmware binaries.
Thanks a lot mate, worked first time. Much appreciated! :)
If it weren't for this video, I have no doubt I would have been too intimidated to try the Community Firmware upgrade on my own. Thanks to this video it worked like a charm...great video!
7/26/2022 just updated my cr6-se and it works fantastic ! havent used it for a few years so long overdue but looking forward to trying some prints again. Big thanks for this video !
This is how you give UA-cam value....superb effort, I love this, thanks a stack!!!
Thank you so much! This was an easy guide to follow even with a newer version for a newbie like me. Again thank you so much, I can't wait to get back to printing.
Thank you so much for your time and help i watched this so many times to get all 3 updated
Ive held off on factory default since I got my cr6-se. Thank you so much for making this so dam easy!
Thank you so much. Extremely helpful- especially the part about the motherboard not taking!!
Massive thanks! Just upgraded my printer and it's great! Thanks for sharing.
Thank you very much for the video!. It helped me a lot. Very good firmware development. I recommend it, excellent work by Sebastian's team. Now the printer has leveled up and it is excellent. Thank you very much again for teaching how to install this fabulous Firmware. Greetings!.
CR6-Max runs perfectly also on this new Community Firmware WELL DONE!!
thank you soo much, I was scared, and now I'm not. This video helped greatly, works like a charm now!
Thanks. Just worked perfectly. Had to format the micro SD on a Mac in terminal using the instructions in the readme file. Put on the latest version and up an printing in about 30 min.
The discord link you provided isn't working
Thankyou for this really great explanation. Now we can print again!
Thanks man I was having a really bad time trying to install the firmware!
Thank you. I've been struggling with this and you made me understand.
If there's so much people working on it, it's probably a very nice printer.
Haven't gone to the community FW yet, but when I do, was your screen timing out after only a few seconds after you updated to v6? If so, that'll get annoying really fast.
Just installed the community firmware, everything works great.
One thing you didn't mention in your video ( but it is mentioned in the read me files ), you screen needs to say " T5L1 DGUS2 V3.5 2020.07.30 " at the very top while / after doing the screen firmware ( that red text ) . If it is a lower or higher V number, your screen will be blank after taking out the micro sd card.
If this is the case, simply add the files from the "CR-6 kernel upgrade" map to the "DWIN_SET" map and start over again with the screen firmware. Everything should be fine after that.
Really great video! Thank you! But i was wondering about the SD card (not the micro SD) can it be taken out to transfer prints on? Or does it need to be inserted at all times now with the firmware? :O
thank you very much, super video.
Hey Jim, I followed this video and upgraded my firmware to the Community version.......LOVE IT! Now I have a question since new versions have come out. Do I have to flash both the screen and firmware or can I just upgrade the firmware to the new version?
:D nice guide it help me alot for my CR6-se doing a print right now aanyway thx @The Edge of Tech you rock :D
Thank you!!
I din't see anymore videos done, by you, on the CR6-SE. Just curious - how come? Is the printer a piece of garbage / junk?
Awesome video Man thanks very much well done
Great video dude
so smooth now, thanks everybody
Great thank you so much for you easy to follow explanation thanks also to the community, my printer works great now had issues with leveling but all fixed, A************ to all
Do you have a video that gives step by step to install a BMG on to the cr6 se? This video was very clear adn straight forward so keep up the great work.
I don't, but I'll add it to the list!
When in doubt, took at the mainboard.
For sure!!
i think creality should definitely hire these guys!
Hello, I don't information on the compatibility with what it seems to be latest motherboard of the CR-6 SE, the "CR-ERA_V1.1.0.3" version. Would the firmware for the 4.5.3 version compatible ?
Thank you for the help!
Thank Man! it worked perfect
Great job still deciding which printer to get. Ev2 or this.
I bought the cr6se because it was only 20% more than the E3v2 in stores around my country. Seemed like it would be worth it for the extra features, and hoping that there are no lingering magic smoke issues on whatever ones they had in stock
Nice video! I saved time by using one card for both.
How?
Legend
While watching the bed level process your nozzle temps seem to be up and down. Did you run a PID tune after the upgrade?
I did not for that video
Jim,, Good video. I no longer have mine but will pass this on. Does this provide new functions / features? This would be easier if the display Micro SD card could be accessed with out removing the screen
Thanks! Ya, it's much better than my stock firmware! You can see a list github.com/CR6Community/Marlin/releases/tag/v2.0.7.3-cr6-community-release-5-beta the changes here!
@@TheEdgeofTech Thanks for the link. It seems like a lot of improvements have been made. This is one reason that I gave the printer to my neighbor, it was just too limited and very little upgrade options
I went to print something and the screen is just a blank screen. I tried to reflash the screen and it does get any further then 3 lines and I left it to see if it's going to finish and after a couple hours was still stuck at that point. I'm not sure what to do from here, can you help me out?
Great video 👍
Aside from some new icons, whats the difference
Any videos on preparing the sd card on a Mac? I am a noob and have a hard time understanding the instructions on README
I know this video is a bit old, but does anyone have directions on how to change the firmware size of the bed on my CR6SE? I did a change and my bed is now limited narrower by direct drive mount.
Hi thank you very much i love your prestance i have the version 2.0.1.3 which mother board is ? thank.
finally is version 4.5.3 thank its work
I have a CR-6SE and its been great so far, but I am starting to notice the firmware holding me back when compared to my manually compiled firmware of my Ender 3 Pro. This video is a year old now, so I was hoping you could give a little direction on where I can find the latest firmware for my CR-6 and ask if you recommend I upgrade?
Warlock tower in the background!!!
Is the community firmware still the first choice?
I've tried many times to flash my TFT I got mine with a motherboard that says CR -ERA 1.1.0.3, I've read I need to use the CF6.1-Final-cr6-se-v4.5.3-mb-2021-06-04-16-53 but after flashing it multiple times and following the instructions here it still doesn't work. When I boot up it says creality community firmware in the loading screen but it just stays there. Any advice or something else I could try? Thank you!
Still no one replied to this???
Thank you!! easy to follow, Why did you use a 8gb micro sd when you said 16gb would be enough?? tbf I also used an 8gb micro sd
ive got a question. No one seems to want to provide a proper explanation as to why the nozzle temp is set to 0 when leveling the bed as the z axis goes down. wouldnt you be getting inaccurate measurements of the bed if youre probing all 16 points at varying different temperatures? so one point can probe at 149 then the next gets probed at 140 and so on.
Is the Firmware only a benefit for the Human Interface?
Hi! I've just ran this procedure in my printer (all installed without issues) and it failes to heat up afterwards, so it´s not even able to do the bed leveling. Any idea what might be going wrong? Many thanks!
bro im having the same issue did you find anything out yet?
Bro im not sure if i want to do this now that i already have bed issue, my bed is moving slowly some times and so the nozzle and the bed are never centred
What are the biggest differences/significant advantages to use the community firmwares? I am struggling to find two SD card types to flash the machine, and am wondering whether it is worth the effort…
I followed the steps including copying the kernel upgrade files into DWIN_SET folder. My screen gives me the updates Community Edition splash screen, beeps once and freezes at 100%.
The same is happening for me.
Did you find a fix?
@@ericmaggard6182 same. Update?
@@Wicky_FPV Its been awhile so I forget exactly how I got it to work. I know once I bought a new SD card with the correct specs I was able to get it to work. Best of luck!
thanks Jim!!!
I didn’t see any features listed that I don’t already have. What am I missing? How does this make the printer work better?
That's what I was hoping to understand. Is there a reason I want this over Marlin?
Edit: this is from their github
This Marlin fork has the goal of cleaning-up the source code changes for the CR-6 so it can be merged upstream. We also want to extend the functionality to make it fully functional
So maybe Marlin doesn't currently have support and they are working on fixing that and then merging with the main branch of Marlin.
You can find the list of changes and new/upgraded features here: github.com/CR6Community/Marlin/releases/tag/v2.0.7.3-cr6-community-release-5-beta
Cura "Pause" and "Filament Change" scripts now work. Z-height offset is now adjustable to 0.01mm, on the fly flow rate, and better bed leveling are just a few of the features I use and love.
I just upgraded firmware to 6.1, and no matter what I do, auto-leveling does nothing. It heats up. homes and then just sits there. It doesnt level. Couldn't find anything else on the github about others having this issue.
Try running the firmware again, and make sure it's the newest version. Just out of curiosity, what's it heats up and it's just sitting there, what happens if you turn the nozzle temperature down a degree or two. Does it start?
@@TheEdgeofTech I tried launching the firmware on the main sd card 2 or 3 times. Still does the same thing. It heats to 145 for hotend and 50 for the bed. I can't change the temp of anything, I can't even hit back, as it just says " it needs to finish up "
@@xXEagle3y3Xx Try changing the firmware name on the card. Then run it again..
Also to note, when it homes, it stops immediately after the bar hits the red home laser, so it sits a good inch or so above the bed
Hi there, thank you for the video.
I have updated my Printer and It works great but i started noticing that the printer is taking longer, way longer than before while printing the same objects.
What do I do if I do not have any display on my touch screen? There is nothing there and it won't turn on. Just a fan and a flashing light in the extruder.
My board says V1.1.0.3 so which firmware would I need?
You have to flash the v4.5.3 firmware
the printer isnt recognizing the screen firmware and i dont understand why
JIm, question. I have updated per your instructions and I believe firmware is ok with version 6, but problem when the printer is homing the nozzle gets press on the glass plate. NOTE:I have done reset factory. HELP HELP. I tried to install old firmware and problem still there, I have to assume all the zoning is bad ALL help is really apreciated
Upgrade to their newest one And make sure you reset the EEPROM when you're done.
I followed everything and can't seem to flash the motherbaord firmware :/ just loading up eternally, any tips?
OK Stupid question. I'm trying to figure out which motherboard I have but there's no number on board. I looked in the info and have the 2.0.1.9, so I'm holding off until I get figure out these questions. I hope you can help me.
Hi not good the new update does not work the back button does not display the time properly and there is still a problem with the display. :( Where can I find the pre-update ??? creality cr6 se. Which is good for eliminating the initial temperature drop in printing
This firmware not workıng for era v1.1.0.3 mainboard. Heatbed and nozzle heating problem. How can I get offical firmware for era v1.1.0.3?
If you have an older 113 board I would check out the TH3D firmware.
my printer is not referencing the z axis, I can't make my nozzle find the bed. Canyou help me?
Hello guys I had a problem with the installation and the touch doesn't work anymore. I tried to go back to the original software and it doesn't work either. could you help me?😭
I just tried this and the screen totally rejected the update. I have a new printer with the v1.1.0.3-ER mainboard. I followed these instructions and the included the Kernel update files for the screen as the text file instructs and the screen booted as normal. I rebooted multiple times and it didn't read the card. . When I went to the "Info" tab, it had no version. I removed the card and rebooted the printer and it was as if nothing happened. I wonder if there's been a revision to the screen firmware since the most recent update.
Good question. I would check on the firmware page to see. Also you could ask the question there as well!
@@TheEdgeofTech The issue was the printer's screen didn't like my 16GB micro SD card. I formatted a 32GB as a 16GB and it recognized it. I'm all good now. Thank you for the awesome videos and content.
i did all this and my printer will not heat up now what do i need top do
My CR-6 SE would not level anymore. So I reloaded the release 6 software and still had the same problem. Do you have any ideas that might help? I reloaded the beta 5 version and it works, but not as good as the latest. Any ideas?
I would ask in the community forum for the firmware on get hub. They would have the best answer to that one.
Thank you.
just updated to version 6 final. still had to change bin file name to 1
its good explanation
but this firm wear dont have restart if the power shut down..
am im right?
Bonjour à Tous ! Pouvez vous me confirmer qu'en exécutant la mise à jour pas à pas du Firmware communautaire, cela fonctionne très correctement en date du 31 mai 2022 ?
Et juste une petite remarque sur le gars de la vidéo, euh sans être méchant mais plutôt méfiant, ce gars là ne m'inspire pas vraiment confiance, alors si il y a des gens qui ont installés cette fameuse MAJ, je souhaiterai cordialement avoir des retours positifs avant de risquer de mettre ma machine en carafe, par avance merci!
Note: j'en suis a ma deuxième imprimante, la précédente qui fonctionne toujours parfaitement, mais manquant un peu de précision et d'options je trouve (Elegoo Neptune 2S), je souhaite me diriger vers un Upgrade ou plutôt ici vers un changement complet du Firmware, ceci en ayant auparavant bien maitrisé La CR-SE fonctionnant sous Cura, donc c'est une évolution sage et maitrisée j'espère.. merci à tous de vos retours (même si je sais que ce n'est pas la place idéale pour ce genre de demande
Great video. Unfortunately, after flashing everything, it now drives the head into the build plate when it auto-homes. I've verified the motherboard version and firmware versions (I'm aware that is you install new version firmware on old version MB it does this, but I've verified I have new MB version). No idea.
I Dont see a version 6 link like what you said you would do in the video.
Well I used the same cards as you did and when updating the display, it jumps right to tge normal screen. Before you ask, I did everything you did. Any thoughts?
I have updated my firmware to version 6, would i use these same instructions for version 6.1?
My printer beeps a bunch when I boot it up now, the blue light is blinking and doesn’t stop, and I see no firmware version listed on the menu. Also , no files appear on the file select. Can you please help me fix this?
Has the community firmware 6 released yet? Could I have the link if it has?
Yes!
@@TheEdgeofTech Thank You! I just installed the Pre Release 6 on it and it’s really cool!
Thank you for share this things, I'm trying to do the Upgrade but I got a stuck on the LCD with .HZK files, you know what to do? thank you in advance