Dag bro, I just finished watching another one of your videos about this from about a year prior; sorry to see that you are in the same boat and definitely sorry to see that it stopped during your conclusion demonstration 🤦🏾♂️ I have the same problem so I was rooting for it to work this time. Welp, time for me to go out there and see what I can figure out about mine. Thanks for the walk-thru (again).
@@northcackalackylife6175 I might’ve 🤔… a few days ago I took it to an automotive shop down the street but they said they couldn’t find the part anywhere and told me to take it to the dealership. I’ll hit them up about the recall, thanks!
My last bushing replacement lasted six months.....saw a video where someone suggested thermoplastic. Another suggested zip ties to keep it in place. Almost opted for the entire transmission but haven't got there yet.......
There is a recall on the 2013 Chevy Equinox for this windshield wiper issue. They haven't yet expanding it to other model years. But I had the same issue with my 2015. I've replaced the wiper transmission 2, with the Dorman model, and its always that same bushing. Always fails in the rain too. As if when the motor is turning that final small arm gets in a bad position and has some resistance, then it all breaks. Thanks for the video.
Thanks for the tip man Good video I found out too it's a little easier if you heat it up with a heat gun you can push it on by hand worked out for me I broke the first two.lol
I just did this on my 2012 Equinox and have to tell you this video was a great help. I was able to pull the old one and install the new one in about 30 minutes. Appreciate your clear directions.
Just had the same problem. Though I just Mickey Moused it for now - using thick rubber bands to keep it from popping out. I'll deal with actually replacing it in the spring.
Where in the hell were you able to find the wiper linkage bushings I've been looking for the wiper transmission bushing everywhere and cannot find it. Can you please tell me where you found them
Same problem definitely would have worked if you drilled out the middle and connected with something that way. How’s the car in oil they have an engine defect from that year even a recall because the engine burns off the oil The car runs you just got to keep feeding it oil
I had a fleet of HHRs I could drill them out and nut and bolt. 2015 No room for nut and bolt. I like the idea of the Delco replacement. Gonna try other sizes to see first.
GM is the piece of crap , they should have never allowed this design to leave the factory, and won't even allow you to purchase the correct replacement bushings.
Don't ever buy a 2012 either same problem also when it came out of the dealer it had bad rings using oil like crazy . It took a whole year for the dealer to get an okay from general motors to overhaul the engine. And the worst part it was my daughter's car and I talked her into buying it. piece of crap 😠
Dorman doesnt make them at all for this vehicle!! You buy a new wiper transmission without the motor. Or go to the junkyard, but you dont know how long it will last. The part number he is using is for a damn Nissan or something!!!
I’m pretty sure you’re wrong on that but I don’t have time to verify. It was an exact match to the one I took off. I’ll take your word for it but I don’t think a different bushing would do any good it’s just a sorry piece of crap from the start
Well being a FULL-TIME mechanic YOU are wrong! You provided the wrong part number to everyone here!! The DORMAN CATALOG i have here beside me says its for NISSAN VEHICLES!! www.dormanproducts.com/p-7639-49449.aspx?origin=keyword. This is from online. And this IS WHY your bushings popped off 10 TIMES!!!! Im not trying to be an ass. I want you to learn from YOUR mistake!! Ive made plenty myself. Just because something "looks" IDENTICAL doesnt mean it will fit.
Ive been using these dorman bushings FOR SEVERAL YEARS and they have never popped back off and NEVER came back to my shop!!! You must use them for THE CORRECT VEHICLE!!
I just drilled a hole straight through the bushing from top to bottom, Popped a cotter pin through, And was good to go. Don't know how long it will last, but traded it in a year after the repair and was still holding.
@@laceyurdiales6888 it lasted a year and I traded it in, At that point it was still holding. I did the same fix on a friend's Pontiac G6 also, And that's been holding the past 6-7 months or so now.
Did this today on a 2010 and it sucks azz those bushings were cheap kept popping off after putting on and wipers goung wrong way lol took off and on 20 times or more best thing is JUST BUY A NEW ASSEMBLY instead of wasted hours trying to figure it out😂 oh if the motor is good you can just buy the linkage save a few dollars
To all who have spent money on this fix, you can be reimbursed. GM has a special coverage adjustment for the wiper transmission static.nhtsa.gov/odi/tsbs/2019/MC-10171252-9999.pdf for vehicles 2010 - 2012 and 2014 - 2017 for Equinox and Terrain
2014 purchased new has the same issue at 132K miles, bought the ac delco replacement online for $67 shipped including motor. smh, mechanic wanted over $400 to replace it, I am with you- and also done with Chevy due to their poor engineering
Me and you are riding in the same boat man. I've had to work on my wife's several times. It never seems to hold up. New line of SUV's.. Chevrolet POS Series.
Why buy new linkage if it has the same plastic pieces... I just read a guy said he drilled a hole through the nipple and used a cotter pin. I'm in the same boat as you but am considering the drilling method because the plastic will probably keep stripping.
Just found your video because I got a recall notice for our 2015 Equinox for this same issue. We haven't had this issue, but after seeing your video and some others, I'll definitely be looking into the fix/replacement.
I just ordered a new one Fam 😩 from all the compliments I've seen replacing bushings isn't worth it cuz they break so easily. I have 2012 Terrain I've been waiting for these things to break since I've seen the recall but not on mine only 2013- 2015 are recalled! Of course they broke on the worst day possible biblical rain at least they 🛑 while I was pulling into work. Easy enough to fix diy but poor design by GM. Rubbish ass Suv!!!
You are my UA-cam University Hero! I don't think I would have even tried this if I didn't see your video. My "timing" on blades was a bit off but eventually I got it. Keep posting--for I, too have a POS Equinox... Thank you so much...!
thank you for the video. I used the 7/8th socket with a 5/8th socket, along with a c clamp used for calipers. no grease needed, so far its held together!
Bro , that sucks , I have a 2012 about to change the bushings out right now , I see I’m gonna be taken for a ride on this lol did you end up buying a whole new linkage ? 😊
Richard Ehrne It’s hard to explain, just have to play around with it. When you put it back together the arms on the transmission assembly must have moved. You can snap turn the motor by hand and watch the screws that the wipers attach to turn. If they are turning in opposite directions it’s wrong.
Is it a different issue when one side (passenger) is still working fine & other (driver) is not? So far I've only gone as far as popping off the black plastic cap off the non-functional one to see if maybe bolt was still moving but the arm was just slipping (it was not moving)
Thank u this video helped me alot... just for the end when u talk about it going backwards I seemed to have that happen but It was the placement of the arms...
Hi there, I need to check the hose on my 2016 equinox as the fluid doesn't spray but yet the bottle empties and the motor runs. Was glad to watch your video but I need to know how to remove the four tabs at the beginning. I don't want to break them! Do you have to squeeze when you pull them up or just go for it? Please let me know if you get a chance, thanks!
Just changed the connectors on my 2011 GMC Terrain following your instructions in this video. Worked PERFECTLY, especially the 5/8 and 7/8 field hack. Saved me a bunch of money. Thank you for making this video!
Check out my latest video of what I think will be a permanent or at least long term fix. It’s a little bit of a rig job but cost and difficulty is relatively low.
Im a woman and used this video ty so much! The mechanics tried changing $400! I didn’t even need parts just cleaned it out and put it back together
Watched you and fixed it in no time. I just bought the whole assembly motor and all for 100 bones.
I own a 09 Torent. Not quite the same as an Equinox but close enough. Your tips were helpful in my repair, thanks for posting. 🙂
Don't buy a 2011 Equinox either. Replaced engine, transmission and am about to replace the wiper/transmission assembly too. Thanks for the vid.
Dag bro, I just finished watching another one of your videos about this from about a year prior; sorry to see that you are in the same boat and definitely sorry to see that it stopped during your conclusion demonstration 🤦🏾♂️ I have the same problem so I was rooting for it to work this time. Welp, time for me to go out there and see what I can figure out about mine. Thanks for the walk-thru (again).
Did you catch my permanent fix vid? Also there was a recall from what I hear so dealership may do it for free.
@@northcackalackylife6175 I might’ve 🤔… a few days ago I took it to an automotive shop down the street but they said they couldn’t find the part anywhere and told me to take it to the dealership. I’ll hit them up about the recall, thanks!
My last bushing replacement lasted six months.....saw a video where someone suggested thermoplastic. Another suggested zip ties to keep it in place. Almost opted for the entire transmission but haven't got there yet.......
There is a recall on the 2013 Chevy Equinox for this windshield wiper issue. They haven't yet expanding it to other model years. But I had the same issue with my 2015. I've replaced the wiper transmission 2, with the Dorman model, and its always that same bushing. Always fails in the rain too. As if when the motor is turning that final small arm gets in a bad position and has some resistance, then it all breaks. Thanks for the video.
Thanks for the tip man Good video I found out too it's a little easier if you heat it up with a heat gun you can push it on by hand worked out for me I broke the first two.lol
this just happened to my 2012 Chevy Equinox, I’m going to try this fix tomorrow and see what happens, hopefully it works.
I just did this on my 2012 Equinox and have to tell you this video was a great help. I was able to pull the old one and install the new one in about 30 minutes. Appreciate your clear directions.
About to do this with my 2012 Equinox , darn it
Thanks so much for this video! Just did my 2014 nox. Easy to follow video!
Just had the same problem. Though I just Mickey Moused it for now - using thick rubber bands to keep it from popping out. I'll deal with actually replacing it in the spring.
You saved me 60$. Respect
I found that Dorman 49455 bushings fit very well.
i will try this part no. thank you were did you purchase from
Where in the hell were you able to find the wiper linkage bushings I've been looking for the wiper transmission bushing everywhere and cannot find it. Can you please tell me where you found them
There is A recall on 2014 and 2015 Equinox for this very reason, you get A free repair.
My 1978 daily driver doesn't have any wiper issues.
My rodeo I had the same issue after a while it just kept popping off again And those little plastic things were hard to get in
Hey put the nylon bushings in boiling water for a few minutes makes pushing them in easier
Same problem definitely would have worked if you drilled out the middle and connected with something that way.
How’s the car in oil they have an engine defect from that year even a recall because the engine burns off the oil
The car runs you just got to keep feeding it oil
This is happening to me now., there is a huge amount of ppl and a way for them to replace it all.
I had a fleet of HHRs I could drill them out and nut and bolt. 2015 No room for nut and bolt. I like the idea of the Delco replacement. Gonna try other sizes to see first.
Andrew M check my other video. I drilled and tapped ball joint and used a bolt. Been working ever since.
Thank you mine busted for the 2nd time they made these cars like shit, I just bought the whole linkage
lots a help! thanx for the info!
Was that glue or grease ?
Grease
What well they chged at a shop to do this?
No idea
But there is a recall on some years
Soaking the new plastic piece in boiling water for 3 min. will make it go in without breaking
i just fix mine with jv weld and wire, i hope they last a couple of months
The company sent a recall letter for the windhield wiper failure , they will fix free
Thanks
Dorman 49449 bushings are for Nissan products, probably why they have popped off for the 10th time
Blow these fucking cars up and turn em into the insurance company.
GM is the piece of crap , they should have never allowed this design to leave the factory, and won't even allow you to purchase the correct replacement bushings.
Don't ever buy a 2012 either same problem also when it came out of the dealer it had bad rings using oil like crazy . It took a whole year for the dealer to get an okay from general motors to overhaul the engine. And the worst part it was my daughter's car and I talked her into buying it. piece of crap 😠
Agreed the bushings are crap
You do know Chevrolet and GM have a recall on this problem. They will fix it for free.
Yes I’ve made that comment here I think. When I made the video there wasn’t a recall yet.
American engineered junk
2014 too piece of junk.
Those dorman bushings youre buying, are the wrong ones!! Thats why they kept popping off!
Dorman doesnt make them at all for this vehicle!! You buy a new wiper transmission without the motor. Or go to the junkyard, but you dont know how long it will last. The part number he is using is for a damn Nissan or something!!!
I’m pretty sure you’re wrong on that but I don’t have time to verify. It was an exact match to the one I took off. I’ll take your word for it but I don’t think a different bushing would do any good it’s just a sorry piece of crap from the start
Well being a FULL-TIME mechanic YOU are wrong! You provided the wrong part number to everyone here!! The DORMAN CATALOG i have here beside me says its for NISSAN VEHICLES!!
www.dormanproducts.com/p-7639-49449.aspx?origin=keyword. This is from online. And this IS WHY your bushings popped off 10 TIMES!!!! Im not trying to be an ass. I want you to learn from YOUR mistake!! Ive made plenty myself. Just because something "looks" IDENTICAL doesnt mean it will fit.
Ive been using these dorman bushings FOR SEVERAL YEARS and they have never popped back off and NEVER came back to my shop!!! You must use them for THE CORRECT VEHICLE!!
@@johnm1055 So what is the right part number? That would be helpful if you could add that information.
I just drilled a hole straight through the bushing from top to bottom, Popped a cotter pin through, And was good to go. Don't know how long it will last, but traded it in a year after the repair and was still holding.
Still holding?
@@laceyurdiales6888 it lasted a year and I traded it in, At that point it was still holding. I did the same fix on a friend's Pontiac G6 also, And that's been holding the past 6-7 months or so now.
I will try this too!
Did this today on a 2010 and it sucks azz those bushings were cheap kept popping off after putting on and wipers goung wrong way lol took off and on 20 times or more best thing is JUST BUY A NEW ASSEMBLY instead of wasted hours trying to figure it out😂 oh if the motor is good you can just buy the linkage save a few dollars
To all who have spent money on this fix, you can be reimbursed. GM has a special coverage adjustment for the wiper transmission static.nhtsa.gov/odi/tsbs/2019/MC-10171252-9999.pdf
for vehicles 2010 - 2012 and 2014 - 2017 for Equinox and Terrain
YOU ARE THE REAL MVP!!
2014 purchased new has the same issue at 132K miles, bought the ac delco replacement online for $67 shipped including motor. smh, mechanic wanted over $400 to replace it, I am with you- and also done with Chevy due to their poor engineering
So o'reilly's said that part number for the bushings only fits.Nissan, it's not for the twenty fifteen chevy.Equinox
Me and you are riding in the same boat man. I've had to work on my wife's several times. It never seems to hold up.
New line of SUV's.. Chevrolet POS Series.
I have a 15 equinox wipers stopped working in heavy downpour. Checked the fuses, those are good next checking the bushings
I had to melt my plastic bushing but it worked very well. Didn't grease it up tho . Still working after 6 weeks
Same BS with the 2016 equinox., that’s what the hell I get for buying a car cuz I thought the name was cool.
How do u keep the blades from goin the opposite directions
Broke 2 packs trying to get 1 on. Gave up after a few hours.
Thanks for the video. I just had to do this on a 2014 Nox. Pain in the ass but your video really helped me out, bud.
Why buy new linkage if it has the same plastic pieces... I just read a guy said he drilled a hole through the nipple and used a cotter pin. I'm in the same boat as you but am considering the drilling method because the plastic will probably keep stripping.
I'm too late, but there is actually a recall for these on 2014-2015 Equniox and GMC. They will replace the entire assembly free of charge.
Just found your video because I got a recall notice for our 2015 Equinox for this same issue. We haven't had this issue, but after seeing your video and some others, I'll definitely be looking into the fix/replacement.
This helped so much. We have a 2015. I took your advice and bought the whole assembly.
Just had to replace the while assemble i have a 2014 and it's nothing but a peice of crap will never buy another chevy or ford again
This is the line for you?
I just ordered a new one Fam 😩 from all the compliments I've seen replacing bushings isn't worth it cuz they break so easily. I have 2012 Terrain I've been waiting for these things to break since I've seen the recall but not on mine only 2013- 2015 are recalled! Of course they broke on the worst day possible biblical rain at least they 🛑 while I was pulling into work. Easy enough to fix diy but poor design by GM. Rubbish ass Suv!!!
Gracias mi ayudo mucho 😊
You are my UA-cam University Hero! I don't think I would have even tried this if I didn't see your video. My "timing" on blades was a bit off but eventually I got it. Keep posting--for I, too have a POS Equinox... Thank you so much...!
Also the is a recall for 2014 and 2015 equinox. Make gm pay for their defect.
Or a 2014 Equinox. I replaced the bushings 5 times before buying the linkage.
thank you for the video. I used the 7/8th socket with a 5/8th socket, along with a c clamp used for calipers. no grease needed, so far its held together!
They finally issued a recall for this problem!
Thank you sir!!!
thank you
Bro , that sucks , I have a 2012 about to change the bushings out right now , I see I’m gonna be taken for a ride on this lol did you end up buying a whole new linkage ? 😊
No, see my other video on permanent fix. Also there was a recall by GM
I tried this and had the problem you mentioned of them going opposite directions how do I get them back to turning the same way
Richard Ehrne It’s hard to explain, just have to play around with it. When you put it back together the arms on the transmission assembly must have moved. You can snap turn the motor by hand and watch the screws that the wipers attach to turn. If they are turning in opposite directions it’s wrong.
Is it a different issue when one side (passenger) is still working fine & other (driver) is not? So far I've only gone as far as popping off the black plastic cap off the non-functional one to see if maybe bolt was still moving but the arm was just slipping (it was not moving)
ML Manville I’m not sure on that. If the linkage is broken they both quit working. Might be stripped at the end of the wiper where it connects.
Way late but yes it’s still the linkage when one spindle moves but not the other.
Did it blow up yet?
Even my wife’s terrain dose the same shit unbelievable
www.cars.com/research/chevrolet-equinox-2014/recalls/
I'm greatful for this video but the part number I have is #49455 . I have a 2015 Chevrolet Equinox LT.
Thank u this video helped me alot... just for the end when u talk about it going backwards I seemed to have that happen but It was the placement of the arms...
Hi there, I need to check the hose on my 2016 equinox as the fluid doesn't spray but yet the bottle empties and the motor runs. Was glad to watch your video but I need to know how to remove the four tabs at the beginning. I don't want to break them! Do you have to squeeze when you pull them up or just go for it? Please let me know if you get a chance, thanks!
My wipers do not go home and do not go full travel. They seem quiet. What controls home/park position and full travel position?
This are very good suvs i love them sale them like hot cakes. Just give them a little love and care
Same boat....2014 chevy equinox... after 125k it has been one problem after the other.
I'm having a hard time popping the tabs. And easy methods to get them off. Thanks
You dont need to put grease, thats why it pops off. it goesin dry
My wife bought sane car. Your the man in the boat with us
Rock auto had the complete assembly for 29
Don't buy 2014 either.
There your problem dorman parts there junk. Just replace the whole think for about $50.oo bucks
It’s $130 over here. No after market parts for this
Just changed the connectors on my 2011 GMC Terrain following your instructions in this video. Worked PERFECTLY, especially the 5/8 and 7/8 field hack. Saved me a bunch of money. Thank you for making this video!
Duly noted
Too late
Check out my latest video of what I think will be a permanent or at least long term fix. It’s a little bit of a rig job but cost and difficulty is relatively low.