HI Bro, Have you done any video on tooling hole manufacturing and outside edge blend using form releived cutter. If so please let me know need to watch those video.
புரி வெட்டுவதட்கான மிக இலகுவான முறை, cam i விட மெஷினில் வேகமா prg செய்யலாம் Exs… Thread M8 (Pitch 1.25) deep 8 mm T5 M06 G54 G00 G90 G40 G80 G00 X0 Y0 S2200 M3 G43 H5 Z20. M8 G00 Z1. G1 Z0 F400. G1 G42 X-4.D05F225.(4+4 = 8/M8) G2 I4.Z-1.25 G2 I4.Z-2.5 G2 I4.Z-3.75 G2 I4.Z-5. G2 I4.Z-6.25 G2 I4.Z-8 G1 X0 G40 G00 Z20.M9 M30 % (D5 Tools T5 Radio’s)👍 not G41 /G42 ✅ (I4. not 14/ i4) * இப் போர்முலாவை பயன்படுத்தி நீங்கள் எல்லா thread ம் செய்யலாம் தனியா நீங்கள் Pitch ம் அதே ஓடர் இல் deep ம் மாத்தினால் போதும் . Quick Program.
One question is if I have thread depth as 25mm but depth of the part is 30mm. Hole should be through hole , How it will be manufactured. If Iam not wrong. Firstly through hole will be drilled and then thread milling will be done ?
And also blind hole ku arc calculation sonnenga la , adha Konja block ah ezhudhii ... Represent pannenga na , enaku konja puriyum nu nenaikran... Help pannuvengala
I am learned a lot of knowledge from this videos
Very knowledge full video
Thank you sir.its very useful
Anna super explanation thanks anna
Good learning .. Thank you
Could you explain Center point feed and contour feed difference in thread milling program .
Thanks👌👌
Thank you
Super bro
Super
Bro starting la iruthu thana ending poganum niga thread aha end la iruthu starting varra mathiri solluriga
HI Bro, Have you done any video on tooling hole manufacturing and outside edge blend using form releived cutter. If so please let me know need to watch those video.
1 inch bsp thread video podunga anna
புரி வெட்டுவதட்கான மிக இலகுவான முறை, cam i விட மெஷினில் வேகமா prg செய்யலாம் Exs…
Thread M8 (Pitch 1.25) deep 8 mm
T5 M06
G54 G00 G90 G40 G80
G00 X0 Y0
S2200 M3
G43 H5 Z20. M8
G00 Z1.
G1 Z0 F400.
G1 G42 X-4.D05F225.(4+4 = 8/M8)
G2 I4.Z-1.25
G2 I4.Z-2.5
G2 I4.Z-3.75
G2 I4.Z-5.
G2 I4.Z-6.25
G2 I4.Z-8
G1 X0 G40
G00 Z20.M9
M30
%
(D5 Tools T5 Radio’s)👍
not G41 /G42 ✅ (I4. not 14/ i4)
* இப் போர்முலாவை பயன்படுத்தி நீங்கள் எல்லா thread ம் செய்யலாம் தனியா நீங்கள் Pitch ம் அதே ஓடர் இல் deep ம் மாத்தினால் போதும் .
Quick Program.
Hi sir, why cutter compensation G40 is not used for each pass.
Taper boring calculation explain panunga adula minor id 8 degree kudutha antha value eppadi kandupidikanum solunga anna
Sir, npt thread milling program explain pls
Sir thread mill tool two side insert sem concept thana...
One question is if I have thread depth as 25mm but depth of the part is 30mm. Hole should be through hole , How it will be manufactured. If Iam not wrong. Firstly through hole will be drilled and then thread milling will be done ?
How to select the feed and speed for thread milling
For borewell rod adapter
Bro diagram degree machine calculation konjam video podunga please
Vtl thread insert bar la iruthu vmc machine la thread mill program epadi panrathu
Hi bro cnc bspt id fine , threading program
All type off vmc tap pitch calculations pls
HMC la thread mill adikama mudyuma sir
Thala , oru doubt !!
Thread mill oda pass complete aaga solla , G90 la cutter ah work zero ku kondu Vara solla , cutter compensation cancel ( G40 ) kudukka venama ...
Straight ah G90 X0. Y0. Kudutha compensate cancel aaiduma ???
Please clear pannunga thala
Thread mill depth initial LA erunthu start pannra mathiri eruntha depth calulathion ethey method tha use pannanuma
Arc forming calculation puriyala innum koncham etailah explain panna mudiuma
And also blind hole ku arc calculation sonnenga la , adha Konja block ah ezhudhii ...
Represent pannenga na , enaku konja puriyum nu nenaikran...
Help pannuvengala
Which place training center
Hi
Sir 1.5 mm OK but 2mm ennang sir puriyala
G 40 cancel pannula
Tools spec soluga sir
sir maryland thread chart dowload link send panunga......
Sir , corner arc.2 chamfer 1×45 manual calculation sollunga solluga
1×45 degree
Sir why calling by inch not calling mm why bro please share me bro
Anna interpolation la end mill use panni program eppudi podurathu na
Already uploaded...
Please watch my videos list
Bro 1 inch-25.4mm. 3/4 inch-26.441mm eppadi varum bro.please koncham thelivuvaa sollunka bro
Use thread chart, don't confuse your self
Bro cutter compensation D03 use pannirukinka appo max dia (26.441÷2)=13.2 so X13.2 and I-13.2 thana kudukanum bro.pls reply bro
X movement G91 LA move pannirkanala 4.6 kudurom
G90 LA move panna 13.2 kuduklanu nenekra u r suggest
Cutter dia minus pannanum
Cutter dia minus pannanum
Taper turning and taper threading sollunga
Already uploaded
Onnum puriyla