Спасибо Вам за просмотр и комментарий. Вы сэкономили моё время для просмотра фейка. Сейчас в инете так много фейков, по этому я сначала читаю комменты.
@@jumaniyazov51 пожалуйста! Все эти видео где из ничего получают kwt электроэнергии из ниоткуда не более чем фейк!! Если хотите бесплатное электричество то поставте солнечные панели
@@jumaniyazov51 No já jsem se zrychleně podíval. Pracoval jsem jako elektromechanik a takových motorů jsem převinul asi dvacet tisíc. Opravdu jsem se podivil, čemu dneska lidé mohou věřit. Sancta simplicitas.
Привяжи себе на горб этот пропеллер - вентилятор и дуй на Марс.. энергии тебе должно хватить..и болгарку с лампочкой не забудь взять с собой..марсиане заценят твою технологию..😂
Пока полной чистоты не будет, это лишь красивый фокус. Поднять всю установку в руки и включить мощную нагрузку и носить на руках на камеру со всех сторон. Until there is complete cleanliness, this is just a beautiful trick. Lift the entire installation in your hands and turn on a powerful load and carry it on your hands to the camera from all sides.
Я таким генератором обеспечиваю всю Прибалтику электроэнергией. Завтра после обеда еще один генератор подключу и начну электроэнергию в Казахстан экспортировать.
the oscillating EM wave is not controled by anything. It just amplifies until it reaches some limit. You may experiment catestrophic result, if current goes too high, causing the wires in transformers and in the stator to melt and take fire, and possibly explode as there's also no temperature/current limiter, except the natural resistance of coper wires of transformers and stator; also without any control of the oscillating EM, I bet it is not stable, and the frequency is most probably growing. That system could then emit undesired EM all around, interfering with radio waves and causing perturbations, because there's also no screening at all to absorb the EM waves radiated on both open sides of the stator. To suppress all these, an electronic device (using some power transistor and a small electric regulator) should stabilize the frequency and check that the "cos-phi" (angle between voltage and current) stays within the design limits of the stator (about 0.7 to 0.85 according to the plate). Otherwise that device may be dangerous. May be if the EM oscillates too fast, the 2 transformers may start to vibrate: they are not firmly maintained, just sticked with a basic rubber. If the transformers move, they will interact negatively with the oscillating wave, and the system may stop working, for no longer being in correct phase. In the video, there's no vibration, but the video is short. That engine should also never be left without a charge to dissipate the excess of energy. And you should not leave the small microwave motor (0.75W) plugged in for long, it will not resist if it has to absorb high currents. But I bet that the system cannot run for long, and the cos-phi will start varying (along with the frequency), and angular polarisations will have a negative effect on the inducted currents, causing the wave to turn off, and this is not easy to predict (depends on various noises, including temperature of the system) A basic security should be to install fuses in the wires connecting the two transformers to phases of the stator, so that it can also stop the system. And you can turn off the system by inserting an On/Off switch on those wires (the alternative is to remove the magnets on both sides, but if the system becomes unstable, these magnets will be pushed away by the oscillating EM wave having the incorrect polarity. In the video this works only because of a specific length of the bar and position of the two transformers: the osillating EM ways is propagated along the central bar, which is thick enough to support high currents without melting (but this cannot be said about the thin helicoidal wires in the 2 transforrmers and in the stator). The way the EM wave oscillates on the central bar (at specific wave lengths) is also dependant on the material with which it is built (it influences the speed of electrons), but also from the temperature and hygrometry of the air (where magnetic waves travel between the central bar and the stator). Try building it yourself, it may not work at all, unless there's a way to adjust the length of the bar or the horizontal position of transformers near both ends of the central bar. So alone, this system canot be stable. Either the builder in the video was very lucky, or he did not film here the many attempts made to adjust the system, and did not show the effective measurements he made to make it work in a stable way long enough to take short video captures (reassembeld later).
Thank you for the explanation. I set up similarly, but instead of the motor stator, I used a coil with thick wire. Result - 0. I don't know if it still makes sense. Your comments are very valuable. Thank you.
This as already been invented 100 years ago. The government has this technology but just decides to leave us in the dark about all the cool shit they have
@@ГеннадийС-ъ7ы Мне больше нравится ДЕТЕКТИРОВАНИЕ МАГНИТНОГО ПОЛЯ а особенно ТЕОРИЯ БОЛЬШОГО ВЗРЫВА ИЗ НИЧЕГО подтверждающая РАБОТОСПОСОБНОСТЬ ВЕЧНОГО ДВИГАТЕЛЯ . А вам что нравится - швабра ?
Мне больше нравится ДЕТЕКТИРОВАНИЕ МАГНИТНОГО ПОЛЯ а особенно ТЕОРИЯ БОЛЬШОГО ВЗРЫВА ИЗ НИЧЕГО подтверждающая РАБОТОСПОСОБНОСТЬ ВЕЧНОГО ДВИГАТЕЛЯ . А вам что нравится - швабра ?
Svaka čast, sve pohvale. Apsolutna preporuka svim mladim da se okrenu ovakvim sadržajima umjesto farmi, velikom bratu i sličnim glupostima. Još jednom sve pohvale i pozdrav iz Sarajeva.
А значит и не может быть переменного напряжения. Все источники электрической энергии работают на принципе генератора с вращающимся статором или ротором. Все остальные это преобразователи одной энергии в другую с большим количеством электронных компонентов. Здесь же нет ни чего, одни замкнутые контура, а это значит здесь обман и под столом стоит большая электро катушка подключенная к электросети играющая роль генератора. Как беспроводные зарядки телефонов.
Есть изобретатель если не ошибаюсь в европе который отсидел за свое изобретение на данный момент его сайт работает. Так вот в его тройном кольце и подведенными катушками вокруг для съема электричества там нет движущих частей или моментов, ничего не крутится. "Проект Заряд, Джон Серл"
@@АлексейЦыганков-м2е вот возьмите и повторите хотя бы то, что здесь показали, и поймёте, что это фейк, ложь, и обман. Признаюсь честно, этот якобы генератор, действительно работает. Но только не качестве генератора электричества, а как генератор бабла при просмотрах этого видео, вот так он работает точно и не поспоришь!!!
So as to what i have seen. There is no moving parts? Right? Can you tell us what is the theory? Since the magnetic force applied is "statically" in the coil? Meaning current won't be created in the coil unless there is an alternating magnetic polarity applied to it.
Tesó! Végre feltaláltad!👍 Kidobhatjuk azt a sok atomerőművet végre. Meg azt a sok kóklert is ki lehet rúgni aki a fúziós erőművekre költi a sok sok pénzt 🙃🙃🙃 Minden esetre gratulálok, hogy ennyi energiát fektettél ebbe az átverésbe !🧐
Под столом у вас есть индукционная катушка, ведь по сути вы сделали вторичную катушку для приёма токов фуко то есть по сути это индукционная електро варочная панель, но видео было интересным видно что вы знаете дело ,спасибо
The first law of thermodynamics states that a perpetual motion machine of the first kind cannot exist, and the second law of thermodynamics states that one of the second kind cannot exist. Although those laws are more than a century old, patent applications for such devices are still filed every year. Very ingenious reasoning is often followed, but upon closer examination of these devices, the following two options always remain: either the device does not work, or there is a hidden energy source present.
OK - działa , wymiary wałka z pamięci , zastosowałem mosiężny wałek , pozostałe wymiary organoleptycznie zrobiłem wzrokowo , patrząc na montaż każdego elementu generatora . Wracam z delegacji 2 grudnia i zrobię test na obciążenie i na czas ile wytrzyma w czasie 5 godzin . Pozdrawiam i niedowiarków pozdro !!!
If you watch carefully, you can see that it's spinning. It even changes the direction. Please keep in mind, that it makes 4 rpm only. That's very slow…
l'energia non è statica l'energia deve essere sempre eccitata e creata da qualcuno o qualcosa. non è una batteria che accumula energia, in questo video ti fa credere che ha creato un generatore non un accumulatore
Ja zrobiłem podobne urządzenie i mi super działa...Fantastyczne !!! Sam nie myślałem, że to może działać, a jednak działa...😀podłączyłem lodówkę, pralkę i telewizor i wszystko śmiga jak trza 😄
Я поражаюсь всем этим видосам. Если умеешь и у тебя получается сделать изделие, то не для демонстрации, а для распространения сделай 2-3 экземпляра, для продажи. Кто купит и подтвердит эфективность, тогда в зачет. А так это видосики для пиар проекта фентези нью мен.
So nice of you not to patent this technical marvel and make a fortune while solving the energy problems of the world. I'm so touched, my tears are also 100% real. OMG LMAO.
C’est une découverte extraordinaire, votre configuration vous expose à une forte et encore une fois à « l’effet de Foucault « votre barre centrale est un alliage de nickel à 75 % et aluminium 20% et 5 % de cuivre . 👍
Non ce que on voit présentement c’est un frein magnétique.il faudrait que sa base soit en Plexiglas ou transparente pour que dans un premier temps qu’il prouve qu’il a pas de batterie caché. La vidéo est tellement coupé…. Il est peut-être possible de faire un petit surnuméraire avec un temps limité,mais de dire 10kW 😂. Beaucoup de youtuber vive grassement juste avec les clic que sa génère. Dans un premier temp je voit un arnaque. Il vont sûrement dire qu’il ont déposé un brevet pour ne pas élaborer sur leur découverte. Si c’était vrai dans leur intérêt ce serait de mettre sur la table tout les détails de fabrication. La journée que le produit ce retrouverait sur le marché par n’importe qui ,il pourront revendiquer la paternité de ce produit en demandant légalement une partie des profits sans avoir eu à débourser pour le mettre en marché. Le moment d’une découverte à la production de celui-ci,il ce passe souvent des années. Dans ce genre de produit il faut qu’il ce battre avec le lobby du pétrole, électrique, et même avec les gouvernements qui sont parfois les marionnettes des lobby. Conclusion il faudra boire jusqu’à la dernière goute de pétrole sur la terre avant de voir ses produits commercialisés désolé.
Yes, it's possible, because it's use homopolar generator at the metal bar and the stator also generate the flux density in the center of the cross section of the asynchronous motor, even without rotor. So, the power generated of the homopolar generator via the metal bar is sufficient to re supply to the stator, then it will self sufficient system.. Good job.....
@fadjar1340 je vois que vous êtes du domaine, pourriez-vous nous en dire plus ? Sur tout comment on peut créer de l'électricité sans bouger les aimants ?
Я вот почти все понял, вот только не понял как двигатель 0.75квт может на выходе дать 10квт. Наверно все дело в наклейках, главное их надо правильно наклеить.
Good morning, first I congratulate you on your genius, I'm talking to people who are unfamiliar with it and can purchase it. Thank you for your response. (I'm from italy)
if I understood correctly the alternative output stops by itself if it is not used because if I understood correctly the magnetic fields will freeze after a while if it has no charge YOUR SYSTEM IS INGENIOUS I CALLED IT MAGNETIC WIND...THANK YOU
The first law of thermodynamics states that a perpetual motion machine of the first kind cannot exist, and the second law of thermodynamics states that one of the second kind cannot exist. Although those laws are more than a century old, patent applications for such devices are still filed every year. Very ingenious reasoning is often followed, but upon closer examination of these devices, the following two options always remain: either the device does not work, or there is a hidden energy source present.
the oscillating EM wave is not controled by anything. It just amplifies until it reaches some limit. You may experiment catestrophic result, if current goes too high, causing the wires in transformers and in the stator to melt and take fire, and possibly explode as there's also no temperature/current limiter, except the natural resistance of coper wires of transformers and stator; also without any control of the oscillating EM, I bet it is not stable, and the frequency is most probably growing. That system could then emit undesired EM all around, interfering with radio waves and causing perturbations, because there's also no screening at all to absorb the EM waves radiated on both open sides of the stator. To suppress all these, an electronic device (using some power transistor and a small electric regulator) should stabilize the frequency and check that the "cos-phi" (angle between voltage and current) stays within the design limits of the stator (about 0.7 to 0.85 according to the plate). Otherwise that device may be dangerous. May be if the EM oscillates too fast, the 2 transformers may start to vibrate: they are not firmly maintained, just sticked with a basic rubber. If the transformers move, they will interact negatively with the oscillating wave, and the system may stop working, for no longer being in correct phase. In the video, there's no vibration, but the video is short. That engine should also never be left without a charge to dissipate the excess of energy. And you should not leave the small microwave motor (0.75W) plugged in for long, it will not resist if it has to absorb high currents. But I bet that the system cannot run for long, and the cos-phi will start varying (along with the frequency), and angular polarisations will have a negative effect on the inducted currents, causing the wave to turn off, and this is not easy to predict (depends on various noises, including temperature of the system) A basic security should be to install fuses in the wires connecting the two transformers to phases of the stator, so that it can also stop the system. And you can turn off the system by inserting an On/Off switch on those wires (the alternative is to remove the magnets on both sides, but if the system becomes unstable, these magnets will be pushed away by the oscillating EM wave having the incorrect polarity. In the video this works only because of a specific length of the bar and position of the two transformers: the osillating EM ways is propagated along the central bar, which is thick enough to support high currents without melting (but this cannot be said about the thin helicoidal wires in the 2 transforrmers and in the stator). The way the EM wave oscillates on the central bar (at specific wave lengths) is also dependant on the material with which it is built (it influences the speed of electrons), but also from the temperature and hygrometry of the air (where magnetic waves travel between the central bar and the stator). Try building it yourself, it may not work at all, unless there's a way to adjust the length of the bar or the horizontal position of transformers near both ends of the central bar. So alone, this system canot be stable. Either the builder in the video was very lucky, or he did not film here the many attempts made to adjust the system, and did not show the effective measurements he made to make it work in a stable way long enough to take short video captures (reassembeld later).
Если он только покажет свое лицо То его обязательно за это убьют Через некоторое время (((((( И ещё объявят шарлатаном Вот он и оберегает свою жизнь и правильно делает !!!! Дольше проживет !!!!! А это самое главное жить долго !!!!
Nope he wouldn't be living with everything he ever dreamed off. Nevet to be famous, he wouldn't be rich, he only would be death! Assassination by Oil petro-dollar Mafia! So for yr own Safety can you please stop this free energy bullcrap.. I'm sick of it!
Не уж то НЕ понятно ???? , что в "доске" набор аккумуляторов с опасным для человека напряжением !!! -- Вот для чего эта "доска" оклеена по периметру предупреждающей жёлто/чёрной лентой !!!!!!!!! (Как и в предшествующих фейковых видео-изобретениях...)
Bei allem Respekt, das Experiment erfolgt bei mir leider erfolgfrei und wird es wohl bleiben: zwei identische 1,2kW-Mikrowellen geschlachtet, einen "passenden" 1,5kW-Drehstrommotor zerlegt und nach Video zuzüglich einiger sicherheitstechnisch erforderlicher Elemente (je 2-polige C10-Sicherungsautomaten für die Mikrowellenspulen und 2-poliger C10-Sicherungsautomat und 10A-Motorschutzschalter für das Gesamtobjekt) aufgebaut und hochmotiviert den Versuch begonnen ... hmpf, mit dem Drehtellerantrieb war ebensowenig etwas zu starten wie mit Alu-Welle, Stahl-Welle, Kupfer-Welle allmählich reduzierter Länge und ohne Wellenverbindung der auf Ständer in Motorachshöhe stehenden Mikrowellen-Hochspannungstrafo-Primärspulen auch nur irgendwas zu induzieren war anstelle des Drehtellers etwas brutaleren Start mittels 230V aus Steckdose hinter B16-Automat, mehrfachst samt einiger Messungen mit Dreheisen-Meßwerken ausgeführt: Impedanz der parallelgeschalteten Mikrowellenspulen 6,57Ohm Impedanz der Δ-verschalteten Motorwicklungen 5,23Ohm auf Motorwicklungen induzierte Spannung bei 230V-Bestromung der Mikrowellen-Spulen mit ~35A etwa 0,54V auf Mikrowellenspulen induzierte Spannung bei 230V-Bestromung der verschalteten Motorwicklungen mit ~44A etwa 0,75V Daß beide 230V-Versuchsreihen jeweils nur kurze Zeit funktionierten, bis die Sicherungsautomaten auslösten, muß wohl kaum erwähnt werden, ich rate Unkundigen aber DRINGEND von Nachahmung ab!!! Dauer der Einzelversuche war lang genug, um Meßergebnisse mit Zeigermeßwerken und Multimetern für Ströme und Spannungen gegenseitig zu verifizieren, da zur Kontrolle jeweils ein weiteres Meßgerät für Effektivwerte mit angeschlossen war. Um rein ohmsche Anteile der Schaltungsteilnehmer ebenfalls zu erfassen, wurden Wicklungswiderstände mit Wheatstone-Meßbrücke erfaßt (0,965Ohm an den verschalteten Mikrowellenspulen, 2,356Ohm an den verschalteten Motorwicklungen, Meßleitungsequipment 0,185Ohm schon abgezogen) Asynchronmotor, festgebremst, 100% Schlupf, damit 5- bis 6-facher Nennstrom in den Ständerwicklungen, magnetische Kopplung der Mikrowellenspulen nur an und von den Stirnflächen des Stators, das "Projekt" war vor Start zum Scheitern verurteilt, schade eigentlich ... Damit wird Vieles klar: Ein Schaltungsstart mit mehreren(!) Drehteller-Getriebemotoren geschlachteter Mikrowellen KANN NICHT funktionieren. Hätte ich bei allem altbekanntem Wissen besser nachgedacht, BEVOR ich enthusiastisch in den Nachbau eingestiegen bin, ... Versuch und Irrtum ... Die Faszination für diese nicht-drehende Idee von "Energieerzeugung" war größer als meine Vernunft, letztere hat wohl komplett versagt. Gibt es IRGENDEINE einleuchtende Erklärung seitens der Video-Kreateure, was wie anders laufen muß, damit ich vlt noch einmal an meinen Versuchsstand gehen sollte?! Meßwerte, vorteilhafterweise nachvollziehbar, könnten da sehr hilfreich sein ...
Any new scientific invention has to go throught two processes -- peer review and independent replication, I understand during peer review this will be rejected, but if others are able to replicate it with your clear instructions, then this unit will reach masses. Can you make a detailed tutorial with diagrams for laymans?
i can see resonance working here on the long bar inside the 50hz vibration on the bar question is which metal can vibrate on 50hz and produce over unity
In The proccess of fabrication of magnets ,to activate they use 300 v at 50 amps,,,so he just Made the oscillator starting with external energíy,,but the magnets keep the oscillations,👍
Yes. (Copied from above) the oscillating EM wave is not controled by anything. It just amplifies until it reaches some limit. You may experiment catestrophic result, if current goes too high, causing the wires in transformers and in the stator to melt and take fire, and possibly explode as there's also no temperature/current limiter, except the natural resistance of coper wires of transformers and stator; also without any control of the oscillating EM, I bet it is not stable, and the frequency is most probably growing. That system could then emit undesired EM all around, interfering with radio waves and causing perturbations, because there's also no screening at all to absorb the EM waves radiated on both open sides of the stator. To suppress all these, an electronic device (using some power transistor and a small electric regulator) should stabilize the frequency and check that the "cos-phi" (angle between voltage and current) stays within the design limits of the stator (about 0.7 to 0.85 according to the plate). Otherwise that device may be dangerous. May be if the EM oscillates too fast, the 2 transformers may start to vibrate: they are not firmly maintained, just sticked with a basic rubber. If the transformers move, they will interact negatively with the oscillating wave, and the system may stop working, for no longer being in correct phase. In the video, there's no vibration, but the video is short. That engine should also never be left without a charge to dissipate the excess of energy. And you should not leave the small microwave motor (0.75W) plugged in for long, it will not resist if it has to absorb high currents. But I bet that the system cannot run for long, and the cos-phi will start varying (along with the frequency), and angular polarisations will have a negative effect on the inducted currents, causing the wave to turn off, and this is not easy to predict (depends on various noises, including temperature of the system) A basic security should be to install fuses in the wires connecting the two transformers to phases of the stator, so that it can also stop the system. And you can turn off the system by inserting an On/Off switch on those wires (the alternative is to remove the magnets on both sides, but if the system becomes unstable, these magnets will be pushed away by the oscillating EM wave having the incorrect polarity. In the video this works only because of a specific length of the bar and position of the two transformers: the osillating EM ways is propagated along the central bar, which is thick enough to support high currents without melting (but this cannot be said about the thin helicoidal wires in the 2 transforrmers and in the stator). The way the EM wave oscillates on the central bar (at specific wave lengths) is also dependant on the material with which it is built (it influences the speed of electrons), but also from the temperature and hygrometry of the air (where magnetic waves travel between the central bar and the stator). Try building it yourself, it may not work at all, unless there's a way to adjust the length of the bar or the horizontal position of transformers near both ends of the central bar. So alone, this system canot be stable. Either the builder in the video was very lucky, or he did not film here the many attempts made to adjust the system, and did not show the effective measurements he made to make it work in a stable way long enough to take short video captures (reassembeld later).
In reality, it is a flux flip flop inductor that is shorted out magnetically, opposing itself so the oscillations created by the microwave oven dish motor is enough to trigger a reaction, pulsing the initial source of energy back and forth simultaneously that it keeps oscillating with greater efficiency than any Meissner circuit because it works with a dead magnetic short so to speak, instead of an electrical short, flux concentrations and electricity ring and cancel each other out but it gives enormous amounts of oscillating maf=gnetic energy that is converted back to electricity at 10 or more times from the coils. It could only start up via it's trigger using an oscillation at the proper voltage. Since the coils are tuned to 50 hz, the same frequency sets off and triggers a 50Hz cycle at the same voltage, bouncing it back and forth to infinity no matter what you try to draw from it, I'm guessing gauge of the coils of wire and gauge of wire used basically is the limit via the amperage of the wire and coils. Does this heat up or is it something that stays fairly cool until really loaded? I could actually see how it works in my head, you feed the start up energy into the two outside phase connections and the motor is backfed across two points of the delta in which the stator is wound and connected to the input terminals, then the stator windings reverberate the signal through all three coils, bouncing back and forth until it rings continuously at 50Hz across the coil you broadcasted to. The signal from the little motor is good to start it up, but does it jump to 50 or 60 hz or does this fluctuate a lot?. This is absolute genius. Have you experimented with cancelling the magnetic field using NSNS outward facing in motor armatures driving a dc signal by electromagnet into one winding with universal motors before? I think I understand how you did the last liberty engines like I am saying, no?
La cosa che mi sorprende è vedere come tanti babbei fanno i presuntuosi e fanno ironia convinti che ci sia il trucco quando è tutto chiaro del perchè il progetto funziona. L'unica cosa che mi stupisce è il fatto che non ci sono schermature alle oscillazioni EM e inoltre bisognerebbe capire se sono oscillazioni stabili. Comunque complimenti. Ho costruito anch'io un generatore con un alternatore, ma non con questo sistema. Io ho lasciato la parte mobile della dinamo e quindi fa un lieve rumore. Il tuo sistema è silenzioso al 1000% e anche se comprendo il sistema, ammetto che non ci sarei mai arrivato
In The proccess of fabrication of magnets ,to activate they use 300 v at 50 amps,,,so he just Made the oscillator starting with external energíy,,but the magnets keep the oscillations,👍
This is the most relevant question. Once it is "kickstarted" why doesn't the little kickstart motor (the thing that rotates the glass tray in microwave) keep going like all the other appliances plugged into same power board ??
Absolutely. Take your extension cord from the wall outlet, wrap it twice around the table holding any motor you like and plug your devices directly into it.
I was sitting at the edge of my chair as this build was developing and it was all making sense to me, but I was perplexed as to how you were going to start an oscillation from a solid state generator. . . then you pulled out the synchronous motor and i about fell out of my chair, like watching the plot of a great movie unfold where there whole thing comes together. i know the connecting rod is the same material at the Liberty Engine 2 rotor. My question: can you shed any light on exactly what that alloy composition is? or a least a #### that represents that alloy? I have all the parts for my build but that. also, are the supporting brackets steel or aluminum? thanks!
Самое интерестное ,это ручная динамомашинка которая типа возбуждает всю схему как волшебная палочка,тоесть мгниты с обмотками и начинается генерирование откуда-то свч аж 230в.и,работает даже пятидесятигерцовая болгарка,Тесла отдыхает!!!!
In The proccess of fabrication of magnets ,to activate they use 300 v at 50 amps,,,so he just Made the oscillator starting with external energíy,,but the magnets keep the oscillations,👍
Despues de varios años estudiando la teoria ifotonica de Jose Alfonso Hernandez , has ido capaz de hacer real su teoria. Lo más interesante, a parte de no tener piezas moviles, es la forma de arrancarlo, haciendo girar un toroide. En cuanto pueda lo replico y se lo pasaré al maestro. ESta es la energia libre que nos merecemos. Eres genial.
Забавно, но это не работает так. Учите физику ребята😂. Но автор видео кое-где прокололся, а именно почему так называемый генератор пуска не стал вращаться самостоятельно после запуска всей конструкции. Хотя автор молодец большой он сделал генератор денег из воздуха) Вы просмотры и лайки а он денюшку с ролика.
Если посмотреть внимательно, то он начал вращаться, так же как в микроволновке, медленно. Пересмотрите, я сам вчера пересматривал и убедился что он начал вращаться.
Зачем на тачку ? На космолёт и за пределы галактики ! Электроников в провода запустил, а они там бегают и размножаются да ещё с такой скоростью, что исчерпать невозможно никакой нагрузкой.
Can you make a follow-up video where you plug the light in as well as the fan and pich the Power Generator up with the camera placed so one can see there are no cables under the Power Generator? There are too many videos on FB showing "Free Power" that do not work. If this works you should be able to demonstrate that quite easy
Excellent objection... If people believe this, then no wonder there are so many people who believe the earth is a flat plate... This world works by natural laws, not by magic tricks... (easy fun for the ignorant).. .
@@petarkostic3768exactly. "Free energy"... They don't know the 1st law of thermodynamics. They think it is possible to create energy from nothing or to have zero loss, zero friction, and so on 🤦🤦
it's all about getting clicks and earning money from the videos. They know there are a lot of curious people out there, and unfortunately most of them are also gullible.
Is it based on a Don Smith design? Seems high pwr for 1 set of ring magnets & 1 core. What's freq out? The power tool needs 50/60 Hz. Did you calculate the coils' resonant freq B4 assembly?
I like these videos very much. Amazing work. How do you think out such construction? Big energy companies won't like a mass production of such device. Would such device ever be on the market for sale? I am afraid that we we only see it on this video. Much appreciation for the work making the device and video.
@@perthcowboy2268 Good to know. Have seen quite a lot about Tessla's work and thought of things similar to this for a few years but never had time to do a build myself. Yet that is.
Здравствуйте Либерти я смотрю все ваши изобретения вы гении своего дела хотелось бы узнать только один ответ что это правда. Я понимаю что секрет остаться за вами и есле это так то вы могли бы помоч миллионам людей сказав правду что это реальность а не фокус
Τα 10kw είναι αλήθεια και πραγματικό, αλλά θα χρειαστεί να δειται το βιντεάκι πολλές φορές ώστε να προσέξετε δύο και μόνο πράγματα για να προχωρήσετε στην κατασκευή αυτή, πολλά συγχαρητήρια σε αυτή την ομάδα των ανθρώπων ΜΠΡΑΒΟ ΣΑΣ. 10:26
ПомочЬ ... к стати ... И это лишь фокус для просмотров ... Спроси у этого "мастера" - как удалось достичь 230 и при частоте переменки - в 50 герц . Он не даст ответ. Однозначно.
Hola, el anterior con el motor y alternador me convencia mas, este se ve aun mas sencillo y trabaja igual segun vi, pero los cortes de dicho video me dan a entender que se esconde algo.
Amigo repetir um progeto mecânico que usava imã e 2 bobinas com iman num veio cilindrico meso usando um motor esterno para o girar ele produzia 0 de enegia e foi copiado so ínfimo detalhe não dar para crer em tudo que montra nós videos só testando para saber vai que funciona algum deles se estiver próximo de um rio ou possua um poço com muita agua dar para oroduzir um gerador capaz de gerar uma boa energia
Самое сложное в этой конструкции, это спрятать питающий сетевой провод, с чем автор справился отлично!!!
Спасибо Вам за просмотр и комментарий. Вы сэкономили моё время для просмотра фейка. Сейчас в инете так много фейков, по этому я сначала читаю комменты.
@@jumaniyazov51 пожалуйста! Все эти видео где из ничего получают kwt электроэнергии из ниоткуда не более чем фейк!! Если хотите бесплатное электричество то поставте солнечные панели
мне в этих видео всегда больше интересна как они наёбывают а не наебалово это или нет
@@jumaniyazov51 No já jsem se zrychleně podíval. Pracoval jsem jako elektromechanik a takových motorů jsem převinul asi dvacet tisíc. Opravdu jsem se podivil, čemu dneska lidé mohou věřit. Sancta simplicitas.
Привяжи себе на горб этот пропеллер - вентилятор и дуй на Марс.. энергии тебе должно хватить..и болгарку с лампочкой не забудь взять с собой..марсиане заценят твою технологию..😂
Пока полной чистоты не будет, это лишь красивый фокус. Поднять всю установку в руки и включить мощную нагрузку и носить на руках на камеру со всех сторон.
Until there is complete cleanliness, this is just a beautiful trick. Lift the entire installation in your hands and turn on a powerful load and carry it on your hands to the camera from all sides.
I want to see it working out side on a concrete floor then watch him remove the magnets.
Witam też pracuje nad tym to jest na tą chwilę nie realne. Pozdrawiam.
exactly also when you plug 120volt grinder into 220 it would have bad things happen
❤
@@czesawzaeski1364 zbudowałem dokładną kopie -- ale niestety nie generuje nic -- moze rdzen jest inny niz stalowy
ФЕЙК КРАСИВО ИЗГОТОВЛЕН ! ШИКАРНАЯ МАСТЕРСКАЯ !
Я таким генератором обеспечиваю всю Прибалтику электроэнергией. Завтра после обеда еще один генератор подключу и начну электроэнергию в Казахстан экспортировать.
the oscillating EM wave is not controled by anything. It just amplifies until it reaches some limit. You may experiment catestrophic result, if current goes too high, causing the wires in transformers and in the stator to melt and take fire, and possibly explode as there's also no temperature/current limiter, except the natural resistance of coper wires of transformers and stator; also without any control of the oscillating EM, I bet it is not stable, and the frequency is most probably growing. That system could then emit undesired EM all around, interfering with radio waves and causing perturbations, because there's also no screening at all to absorb the EM waves radiated on both open sides of the stator.
To suppress all these, an electronic device (using some power transistor and a small electric regulator) should stabilize the frequency and check that the "cos-phi" (angle between voltage and current) stays within the design limits of the stator (about 0.7 to 0.85 according to the plate). Otherwise that device may be dangerous.
May be if the EM oscillates too fast, the 2 transformers may start to vibrate: they are not firmly maintained, just sticked with a basic rubber. If the transformers move, they will interact negatively with the oscillating wave, and the system may stop working, for no longer being in correct phase. In the video, there's no vibration, but the video is short. That engine should also never be left without a charge to dissipate the excess of energy. And you should not leave the small microwave motor (0.75W) plugged in for long, it will not resist if it has to absorb high currents.
But I bet that the system cannot run for long, and the cos-phi will start varying (along with the frequency), and angular polarisations will have a negative effect on the inducted currents, causing the wave to turn off, and this is not easy to predict (depends on various noises, including temperature of the system)
A basic security should be to install fuses in the wires connecting the two transformers to phases of the stator, so that it can also stop the system. And you can turn off the system by inserting an On/Off switch on those wires (the alternative is to remove the magnets on both sides, but if the system becomes unstable, these magnets will be pushed away by the oscillating EM wave having the incorrect polarity. In the video this works only because of a specific length of the bar and position of the two transformers: the osillating EM ways is propagated along the central bar, which is thick enough to support high currents without melting (but this cannot be said about the thin helicoidal wires in the 2 transforrmers and in the stator).
The way the EM wave oscillates on the central bar (at specific wave lengths) is also dependant on the material with which it is built (it influences the speed of electrons), but also from the temperature and hygrometry of the air (where magnetic waves travel between the central bar and the stator). Try building it yourself, it may not work at all, unless there's a way to adjust the length of the bar or the horizontal position of transformers near both ends of the central bar.
So alone, this system canot be stable. Either the builder in the video was very lucky, or he did not film here the many attempts made to adjust the system, and did not show the effective measurements he made to make it work in a stable way long enough to take short video captures (reassembeld later).
Thank you for the explanation. I set up similarly, but instead of the motor stator, I used a coil with thick wire. Result - 0. I don't know if it still makes sense. Your comments are very valuable. Thank you.
have you tried to build this yet? i built the easy one with pvc and 2 circle magnets, dont work. have most of parts together now for this one.
i suggest you collaborate and perfect this machine to make a world a better place and share it, so we can have this so called free energy, good luck
This as already been invented 100 years ago. The government has this technology but just decides to leave us in the dark about all the cool shit they have
Bara de argalium? Interesant! Din păcate nu învățăm așa ceva la școală. Secretul rămâne pentru generațiile care vin. 😊
Когда смотрю такие видео то чисто для поржать, уверен что очень много электриков очень громко тоже ржут. 😀
Раньше лапшу цепляли а теперь магниты
@@vadimrind2460.И что больше нравится из двух ??? . Лапша или магниты ??? .
@@ГеннадийС-ъ7ы
Мне больше нравится ДЕТЕКТИРОВАНИЕ МАГНИТНОГО ПОЛЯ а особенно ТЕОРИЯ БОЛЬШОГО ВЗРЫВА ИЗ НИЧЕГО подтверждающая РАБОТОСПОСОБНОСТЬ ВЕЧНОГО ДВИГАТЕЛЯ . А вам что нравится - швабра ?
Мне больше нравится ДЕТЕКТИРОВАНИЕ МАГНИТНОГО ПОЛЯ а особенно ТЕОРИЯ БОЛЬШОГО ВЗРЫВА ИЗ НИЧЕГО подтверждающая РАБОТОСПОСОБНОСТЬ ВЕЧНОГО ДВИГАТЕЛЯ . А вам что нравится - швабра ?
Это лопша но не каша
Svaka čast, sve pohvale. Apsolutna preporuka svim mladim da se okrenu ovakvim sadržajima umjesto farmi, velikom bratu i sličnim glupostima. Još jednom sve pohvale i pozdrav iz Sarajeva.
It's better to study physics for understanding that "free energy" , "zero loss" , "infinite energies" are just frauds.
Jos kad bi ovo bilo istinito a ne montaza bilo bih super
Agradeço a vossa cooperação, partilha e ensinamento. Muito obrigado e muitas felicidades. Continuem e libertem o engenho da energia livre.
That's absolutely genius. The thing that's even more genius is that there are no moving parts.
А значит и не может быть переменного напряжения. Все источники электрической энергии работают на принципе генератора с вращающимся статором или ротором. Все остальные это преобразователи одной энергии в другую с большим количеством электронных компонентов. Здесь же нет ни чего, одни замкнутые контура, а это значит здесь обман и под столом стоит большая электро катушка подключенная к электросети играющая роль генератора. Как беспроводные зарядки телефонов.
@@Зубогрыз ага и через железный стол наводит индуктивную энергию 😁😁😁
Есть изобретатель если не ошибаюсь в европе который отсидел за свое изобретение на данный момент его сайт работает. Так вот в его тройном кольце и подведенными катушками вокруг для съема электричества там нет движущих частей или моментов, ничего не крутится. "Проект Заряд, Джон Серл"
@@АлексейЦыганков-м2е вот возьмите и повторите хотя бы то, что здесь показали, и поймёте, что это фейк, ложь, и обман. Признаюсь честно, этот якобы генератор, действительно работает. Но только не качестве генератора электричества, а как генератор бабла при просмотрах этого видео, вот так он работает точно и не поспоришь!!!
So as to what i have seen. There is no moving parts? Right? Can you tell us what is the theory? Since the magnetic force applied is "statically" in the coil? Meaning current won't be created in the coil unless there is an alternating magnetic polarity applied to it.
красивый фокус ))
I’m really liking your compact direction😅
Tesó!
Végre feltaláltad!👍
Kidobhatjuk azt a sok atomerőművet végre. Meg azt a sok kóklert is ki lehet rúgni aki a fúziós erőművekre költi a sok sok pénzt 🙃🙃🙃
Minden esetre gratulálok, hogy ennyi energiát fektettél ebbe az átverésbe !🧐
Под столом у вас есть индукционная катушка, ведь по сути вы сделали вторичную катушку для приёма токов фуко то есть по сути это индукционная електро варочная панель, но видео было интересным видно что вы знаете дело ,спасибо
Ele é o mestre dos otários e tem muitos que quer copiar essa babaquice!kkk
But the device is setting on a steel table,
КРАСИВЫЙ ФЕЙК ДЛЯ ЛОХОВ !
The world needs this. Seems like it could resolve a lot of pollution problems. Plus it would lift people out of poverty.
The first law of thermodynamics states that a perpetual motion machine of the first kind cannot exist, and the second law of thermodynamics states that one of the second kind cannot exist. Although those laws are more than a century old, patent applications for such devices are still filed every year. Very ingenious reasoning is often followed, but upon closer examination of these devices, the following two options always remain: either the device does not work, or there is a hidden energy source present.
There has been over 6000 patent applications declined under the “economic protection code”.
Does the laws of thermodynamics mean anything or indeed the laws of physics THIS MACHINE CANNOT CREATE ENERGY
OK - działa , wymiary wałka z pamięci , zastosowałem mosiężny wałek , pozostałe wymiary organoleptycznie zrobiłem wzrokowo , patrząc na montaż każdego elementu generatora . Wracam z delegacji 2 grudnia i zrobię test na obciążenie i na czas ile wytrzyma w czasie 5 godzin . Pozdrawiam i niedowiarków pozdro !!!
The small motor you first energize should spin when energy production starts, but it never spins.
If you watch carefully, you can see that it's spinning. It even changes the direction. Please keep in mind, that it makes 4 rpm only. That's very slow…
❤
l'energia non è statica l'energia deve essere sempre eccitata e creata da qualcuno o qualcosa. non è una batteria che accumula energia, in questo video ti fa credere che ha creato un generatore non un accumulatore
Pregunta : porque cuando le da impulso con el motor de microondas, el mismo no sigue girando, puesto que ya tiene energía?
Kręci się, 3 obroty na minutę - jesteś ślepy czy jesteś ignorantem... ?
😂😂😂😂😂
What’s the cost of 1 unit?
Ja zrobiłem podobne urządzenie i mi super działa...Fantastyczne !!! Sam nie myślałem, że to może działać, a jednak działa...😀podłączyłem lodówkę, pralkę i telewizor i wszystko śmiga jak trza 😄
are you saying the truth. Please believe me, I want to do something like this, because I am in dire need of something like this
Microwave turntable motors are all 12 volts, but the one shown here is 220 volts.
Я поражаюсь всем этим видосам. Если умеешь и у тебя получается сделать изделие, то не для демонстрации, а для распространения сделай 2-3 экземпляра, для продажи. Кто купит и подтвердит эфективность, тогда в зачет. А так это видосики для пиар проекта фентези нью мен.
Огромное спасибо собрал такой же ,прям копия теперь я не плочу за свет работает ваше изобретение.
Please reveal the specifications for the production
That'll make the viewers happy
Try!
its eazy :D dont waste time with this and use wall plug :D :D here is too normal AC plug under :D :D
This project should be tested in middle school laboratories to stimulate young people's brains.
So nice of you not to patent this technical marvel and make a fortune while solving the energy problems of the world.
I'm so touched, my tears are also 100% real. OMG LMAO.
😂🤣😂
Once you energize it with the synchronous motor , you switch it off with the switch, but does it kill the circuit or is it still giving 230v ?
@wesleykuo8731 try to replicate ... but do it faithfully with respect to the video
C’est une découverte extraordinaire, votre configuration vous expose à une forte et encore une fois à « l’effet de Foucault « votre barre centrale est un alliage de nickel à 75 % et aluminium 20% et 5 % de cuivre . 👍
Is this correct?
Non ce que on voit présentement c’est un frein magnétique.il faudrait que sa base soit en Plexiglas ou transparente pour que dans un premier temps qu’il prouve qu’il a pas de batterie caché. La vidéo est tellement coupé…. Il est peut-être possible de faire un petit surnuméraire avec un temps limité,mais de dire 10kW 😂. Beaucoup de youtuber vive grassement juste avec les clic que sa génère. Dans un premier temp je voit un arnaque. Il vont sûrement dire qu’il ont déposé un brevet pour ne pas élaborer sur leur découverte. Si c’était vrai dans leur intérêt ce serait de mettre sur la table tout les détails de fabrication. La journée que le produit ce retrouverait sur le marché par n’importe qui ,il pourront revendiquer la paternité de ce produit en demandant légalement une partie des profits sans avoir eu à débourser pour le mettre en marché. Le moment d’une découverte à la production de celui-ci,il ce passe souvent des années. Dans ce genre de produit il faut qu’il ce battre avec le lobby du pétrole, électrique, et même avec les gouvernements qui sont parfois les marionnettes des lobby. Conclusion il faudra boire jusqu’à la dernière goute de pétrole sur la terre avant de voir ses produits commercialisés désolé.
To which terminals do we connect the socket for the starting impulse?
At the voltage input or the voltage output?
you will never get one reply from scamer
Když nemáte motorek z mikrovlnky, tak použijte liščí ocas a ebonitovou tyč.
This is a wonderful ability.
I'd like to purchase it.
I think it should be used in a very important place.
b eta project ,and te price ...lol expensive
Beautiful.. and I happen to have all components.. thank you
Yes, it's possible, because it's use homopolar generator at the metal bar and the stator also generate the flux density in the center of the cross section of the asynchronous motor, even without rotor. So, the power generated of the homopolar generator via the metal bar is sufficient to re supply to the stator, then it will self sufficient system.. Good job.....
Why is this working? Is this not surprising? Seems like you guys aren't saying there is any breakthrough here. Just normal physics stuff, eh?
@fadjar1340 je vois que vous êtes du domaine, pourriez-vous nous en dire plus ?
Sur tout comment on peut créer de l'électricité sans bouger les aimants ?
@@ScottRoberson It's a con, you fool.
@fadjar1340 lo hice y no funciona
So, you made just like this one and it worked 😂
Я вот почти все понял, вот только не понял как двигатель 0.75квт может на выходе дать 10квт. Наверно все дело в наклейках, главное их надо правильно наклеить.
🤣
Странно, когда моторчик завели (генератор), напряжение появилось, но потом моторчик не стал работать (двигатель) и его отключили. 🤗
даже не удивительно что ты ни....... не понял :))
Good morning, first I congratulate you on your genius, I'm talking to people who are unfamiliar with it and can purchase it. Thank you for your response. (I'm from italy)
There is a lot of content like this on UA-cam. After some research, I saw that there is an induction coil under this installation.
여러분 전기와 자기에서 N과 S가 연속적으로 바뀌지 않으면 절대로 연속적으로 전기가 발생한다고 믿습니까? 혹시 원자력이라고 생각합니까? 속이는자와 속는자의 차이는?
No2
Bạn nói rất dúng hoặc họ dùng một cái bếp từ De ở dưới trò trẻ Con
Bạn phải nói rằng ke lừa dối mà học thức kém lại nghĩ mình là thiên tài tetla
Nie ma cewki indukcyjnej ...tylko prad wzbudzajacy
Молодец, дай бог что бы тебе дети на старости лет так же воды дали, как ты всем открытие сотворил....
Nice. What is the shaft in the middle made of? What is the material?
Also the measurements..
the shaft is precisely machined from a secret alloy of precious metals which form a room temperature superconductor, producing overunity in the system
i just made that up btw
@@mrp3066 is iron oxide and metal
The shaft is the original shaft that came with the motor
if I understood correctly the alternative output stops by itself if it is not used because if I understood correctly the magnetic fields will freeze after a while if it has no charge YOUR SYSTEM IS INGENIOUS I CALLED IT MAGNETIC WIND...THANK YOU
How is that possible without rotation to producing ac?In what laws of physics is working on?Thanks.
Kaç Amp, güç, üretiyor?
Как будто побывал в цирке на выступлении хорошего фокусника😅, Вопрос : откуда взялась частота 50Hz?
Ну , так... откуда 10 кил , оттуда ж и 50 герцов)) "не будем им мешать" ))
Оттуда же откуда 10кВт))) из розетки на стене помещения)))
Вот и я задался этим же И почему не происходит срыва частоты? Тоже не понятно, чем она стабилизирована?
Браво!Давно не получал я такого удовольствия от просмотра.
เยี่ยมเลย..อยากได้แบบนี้สักอัน..👍
whaooouuuuuuuuuu magnifique avec vous la terre poura respiré tout en recyclant merci beaucoup jah love🥰😍😇
Hi.
What is the ratio of silver : aluminum in electro magnet field bar? How much should it weight ?
Thank you.
If it works really he would win the Nobel prize 😂
And would win much more money with his own company than with UA-cam rewards 😂
The first law of thermodynamics states that a perpetual motion machine of the first kind cannot exist, and the second law of thermodynamics states that one of the second kind cannot exist. Although those laws are more than a century old, patent applications for such devices are still filed every year. Very ingenious reasoning is often followed, but upon closer examination of these devices, the following two options always remain: either the device does not work, or there is a hidden energy source present.
the oscillating EM wave is not controled by anything. It just amplifies until it reaches some limit. You may experiment catestrophic result, if current goes too high, causing the wires in transformers and in the stator to melt and take fire, and possibly explode as there's also no temperature/current limiter, except the natural resistance of coper wires of transformers and stator; also without any control of the oscillating EM, I bet it is not stable, and the frequency is most probably growing. That system could then emit undesired EM all around, interfering with radio waves and causing perturbations, because there's also no screening at all to absorb the EM waves radiated on both open sides of the stator.
To suppress all these, an electronic device (using some power transistor and a small electric regulator) should stabilize the frequency and check that the "cos-phi" (angle between voltage and current) stays within the design limits of the stator (about 0.7 to 0.85 according to the plate). Otherwise that device may be dangerous.
May be if the EM oscillates too fast, the 2 transformers may start to vibrate: they are not firmly maintained, just sticked with a basic rubber. If the transformers move, they will interact negatively with the oscillating wave, and the system may stop working, for no longer being in correct phase. In the video, there's no vibration, but the video is short. That engine should also never be left without a charge to dissipate the excess of energy. And you should not leave the small microwave motor (0.75W) plugged in for long, it will not resist if it has to absorb high currents.
But I bet that the system cannot run for long, and the cos-phi will start varying (along with the frequency), and angular polarisations will have a negative effect on the inducted currents, causing the wave to turn off, and this is not easy to predict (depends on various noises, including temperature of the system)
A basic security should be to install fuses in the wires connecting the two transformers to phases of the stator, so that it can also stop the system. And you can turn off the system by inserting an On/Off switch on those wires (the alternative is to remove the magnets on both sides, but if the system becomes unstable, these magnets will be pushed away by the oscillating EM wave having the incorrect polarity. In the video this works only because of a specific length of the bar and position of the two transformers: the osillating EM ways is propagated along the central bar, which is thick enough to support high currents without melting (but this cannot be said about the thin helicoidal wires in the 2 transforrmers and in the stator).
The way the EM wave oscillates on the central bar (at specific wave lengths) is also dependant on the material with which it is built (it influences the speed of electrons), but also from the temperature and hygrometry of the air (where magnetic waves travel between the central bar and the stator). Try building it yourself, it may not work at all, unless there's a way to adjust the length of the bar or the horizontal position of transformers near both ends of the central bar.
So alone, this system canot be stable. Either the builder in the video was very lucky, or he did not film here the many attempts made to adjust the system, and did not show the effective measurements he made to make it work in a stable way long enough to take short video captures (reassembeld later).
Если он только покажет свое лицо
То его обязательно за это убьют
Через некоторое время ((((((
И ещё объявят шарлатаном
Вот он и оберегает свою жизнь и правильно делает !!!!
Дольше проживет !!!!!
А это самое главное жить долго !!!!
Nope he wouldn't be living with everything he ever dreamed off. Nevet to be famous, he wouldn't be rich, he only would be death! Assassination by Oil petro-dollar Mafia! So for yr own Safety can you please stop this free energy bullcrap.. I'm sick of it!
Super generator👍
I'd like to know if you made the shaft out of alum/silver or is it just iron thanks for showing this
Dont botther. Brother.. this. Not. Real .. their. Is no voltage drop .. avr too
that sharft is batery hahahaha.this is not real this is joke.
А почему не поднял во время демонстрации?, я хотел бы посмотреть на провод идущий из стола🤣
Не уж то НЕ понятно ???? , что в "доске" набор аккумуляторов с опасным для человека напряжением !!!
-- Вот для чего эта "доска" оклеена по периметру предупреждающей жёлто/чёрной лентой !!!!!!!!!
(Как и в предшествующих фейковых видео-изобретениях...)
Вот такой вот лохотрон-технолоджи😀
Ciao amico mio, sarestì. Disposto a vendere questo generatore? Grazie di cuore per una tua risposta ❤ !!!
Please do another video Lifting the Unit while its powering a device to prove No Incoming-AC Line connected.
Bei allem Respekt, das Experiment erfolgt bei mir leider erfolgfrei und wird es wohl bleiben:
zwei identische 1,2kW-Mikrowellen geschlachtet, einen "passenden" 1,5kW-Drehstrommotor zerlegt und nach Video zuzüglich einiger sicherheitstechnisch erforderlicher Elemente (je 2-polige C10-Sicherungsautomaten für die Mikrowellenspulen und 2-poliger C10-Sicherungsautomat und 10A-Motorschutzschalter für das Gesamtobjekt) aufgebaut und hochmotiviert den Versuch begonnen ...
hmpf, mit dem Drehtellerantrieb war ebensowenig etwas zu starten wie mit Alu-Welle, Stahl-Welle, Kupfer-Welle allmählich reduzierter Länge und ohne Wellenverbindung der auf Ständer in Motorachshöhe stehenden Mikrowellen-Hochspannungstrafo-Primärspulen auch nur irgendwas zu induzieren war
anstelle des Drehtellers etwas brutaleren Start mittels 230V aus Steckdose hinter B16-Automat, mehrfachst samt einiger Messungen mit Dreheisen-Meßwerken ausgeführt:
Impedanz der parallelgeschalteten Mikrowellenspulen 6,57Ohm
Impedanz der Δ-verschalteten Motorwicklungen 5,23Ohm
auf Motorwicklungen induzierte Spannung bei 230V-Bestromung der Mikrowellen-Spulen mit ~35A etwa 0,54V
auf Mikrowellenspulen induzierte Spannung bei 230V-Bestromung der verschalteten Motorwicklungen mit ~44A etwa 0,75V
Daß beide 230V-Versuchsreihen jeweils nur kurze Zeit funktionierten, bis die Sicherungsautomaten auslösten, muß wohl kaum erwähnt werden,
ich rate Unkundigen aber DRINGEND von Nachahmung ab!!!
Dauer der Einzelversuche war lang genug, um Meßergebnisse mit Zeigermeßwerken und Multimetern für Ströme und Spannungen gegenseitig zu verifizieren, da zur Kontrolle jeweils ein weiteres Meßgerät für Effektivwerte mit angeschlossen war.
Um rein ohmsche Anteile der Schaltungsteilnehmer ebenfalls zu erfassen, wurden Wicklungswiderstände mit Wheatstone-Meßbrücke erfaßt (0,965Ohm an den verschalteten Mikrowellenspulen, 2,356Ohm an den verschalteten Motorwicklungen, Meßleitungsequipment 0,185Ohm schon abgezogen)
Asynchronmotor, festgebremst, 100% Schlupf, damit 5- bis 6-facher Nennstrom in den Ständerwicklungen, magnetische Kopplung der Mikrowellenspulen nur an und von den Stirnflächen des Stators, das "Projekt" war vor Start zum Scheitern verurteilt, schade eigentlich ...
Damit wird Vieles klar:
Ein Schaltungsstart mit mehreren(!) Drehteller-Getriebemotoren geschlachteter Mikrowellen KANN NICHT funktionieren.
Hätte ich bei allem altbekanntem Wissen besser nachgedacht, BEVOR ich enthusiastisch in den Nachbau eingestiegen bin, ...
Versuch und Irrtum ...
Die Faszination für diese nicht-drehende Idee von "Energieerzeugung" war größer als meine Vernunft, letztere hat wohl komplett versagt.
Gibt es IRGENDEINE einleuchtende Erklärung seitens der Video-Kreateure, was wie anders laufen muß, damit ich vlt noch einmal an meinen Versuchsstand gehen sollte?!
Meßwerte, vorteilhafterweise nachvollziehbar, könnten da sehr hilfreich sein ...
Any new scientific invention has to go throught two processes -- peer review and independent replication, I understand during peer review this will be rejected, but if others are able to replicate it with your clear instructions, then this unit will reach masses.
Can you make a detailed tutorial with diagrams for laymans?
He won’t be long for this world if he starts helping others successfully build them.
Please give us all the details to make one, you would be a hero
Did you receive the info you requested?
I've the details information
@@freeelectricgenerator7921 please send them to me
원리가 이해 안가네요
no that is not the way
i can see resonance working here on the long bar inside the 50hz vibration on the bar question is which metal can vibrate on 50hz and produce over unity
In The proccess of fabrication of magnets ,to activate they use 300 v at 50 amps,,,so he just Made the oscillator starting with external energíy,,but the magnets keep the oscillations,👍
@@MrAcapela how do we fabricate the magnet
I am a new subscriber you have my full attention
Thank you!!!
Hello, does the bar in the center need a specific measurement (size, diameter)? Is this the motor shaft? THANKS
Yes. (Copied from above)
the oscillating EM wave is not controled by anything. It just amplifies until it reaches some limit. You may experiment catestrophic result, if current goes too high, causing the wires in transformers and in the stator to melt and take fire, and possibly explode as there's also no temperature/current limiter, except the natural resistance of coper wires of transformers and stator; also without any control of the oscillating EM, I bet it is not stable, and the frequency is most probably growing. That system could then emit undesired EM all around, interfering with radio waves and causing perturbations, because there's also no screening at all to absorb the EM waves radiated on both open sides of the stator.
To suppress all these, an electronic device (using some power transistor and a small electric regulator) should stabilize the frequency and check that the "cos-phi" (angle between voltage and current) stays within the design limits of the stator (about 0.7 to 0.85 according to the plate). Otherwise that device may be dangerous.
May be if the EM oscillates too fast, the 2 transformers may start to vibrate: they are not firmly maintained, just sticked with a basic rubber. If the transformers move, they will interact negatively with the oscillating wave, and the system may stop working, for no longer being in correct phase. In the video, there's no vibration, but the video is short. That engine should also never be left without a charge to dissipate the excess of energy. And you should not leave the small microwave motor (0.75W) plugged in for long, it will not resist if it has to absorb high currents.
But I bet that the system cannot run for long, and the cos-phi will start varying (along with the frequency), and angular polarisations will have a negative effect on the inducted currents, causing the wave to turn off, and this is not easy to predict (depends on various noises, including temperature of the system)
A basic security should be to install fuses in the wires connecting the two transformers to phases of the stator, so that it can also stop the system. And you can turn off the system by inserting an On/Off switch on those wires (the alternative is to remove the magnets on both sides, but if the system becomes unstable, these magnets will be pushed away by the oscillating EM wave having the incorrect polarity. In the video this works only because of a specific length of the bar and position of the two transformers: the osillating EM ways is propagated along the central bar, which is thick enough to support high currents without melting (but this cannot be said about the thin helicoidal wires in the 2 transforrmers and in the stator).
The way the EM wave oscillates on the central bar (at specific wave lengths) is also dependant on the material with which it is built (it influences the speed of electrons), but also from the temperature and hygrometry of the air (where magnetic waves travel between the central bar and the stator). Try building it yourself, it may not work at all, unless there's a way to adjust the length of the bar or the horizontal position of transformers near both ends of the central bar.
So alone, this system canot be stable. Either the builder in the video was very lucky, or he did not film here the many attempts made to adjust the system, and did not show the effective measurements he made to make it work in a stable way long enough to take short video captures (reassembeld later).
In reality, it is a flux flip flop inductor that is shorted out magnetically, opposing itself so the oscillations created by the microwave oven dish motor is enough to trigger a reaction, pulsing the initial source of energy back and forth simultaneously that it keeps oscillating with greater efficiency than any Meissner circuit because it works with a dead magnetic short so to speak, instead of an electrical short, flux concentrations and electricity ring and cancel each other out but it gives enormous amounts of oscillating maf=gnetic energy that is converted back to electricity at 10 or more times from the coils. It could only start up via it's trigger using an oscillation at the proper voltage. Since the coils are tuned to 50 hz, the same frequency sets off and triggers a 50Hz cycle at the same voltage, bouncing it back and forth to infinity no matter what you try to draw from it, I'm guessing gauge of the coils of wire and gauge of wire used basically is the limit via the amperage of the wire and coils. Does this heat up or is it something that stays fairly cool until really loaded? I could actually see how it works in my head, you feed the start up energy into the two outside phase connections and the motor is backfed across two points of the delta in which the stator is wound and connected to the input terminals, then the stator windings reverberate the signal through all three coils, bouncing back and forth until it rings continuously at 50Hz across the coil you broadcasted to. The signal from the little motor is good to start it up, but does it jump to 50 or 60 hz or does this fluctuate a lot?. This is absolute genius. Have you experimented with cancelling the magnetic field using NSNS outward facing in motor armatures driving a dc signal by electromagnet into one winding with universal motors before? I think I understand how you did the last liberty engines like I am saying, no?
Hello, Thank you for great your explanation! Are you aware of any other devices utilizing this process or additional information on it? Thank you!
La cosa che mi sorprende è vedere come tanti babbei fanno i presuntuosi e fanno ironia convinti che ci sia il trucco quando è tutto chiaro del perchè il progetto funziona. L'unica cosa che mi stupisce è il fatto che non ci sono schermature alle oscillazioni EM e inoltre bisognerebbe capire se sono oscillazioni stabili. Comunque complimenti. Ho costruito anch'io un generatore con un alternatore, ma non con questo sistema. Io ho lasciato la parte mobile della dinamo e quindi fa un lieve rumore. Il tuo sistema è silenzioso al 1000% e anche se comprendo il sistema, ammetto che non ci sarei mai arrivato
Ráno prášek zelený, v poledne růžový a večer oranžový, 3 krát denně svěrací kazajka.
Фокусник браво 🎉
Very nice Engineering 👍 👍 👍 👍 👍
I would like to understand how this works, look something like ZPEF stuff. No moving parts looks great. A follow up video would be nice.
In The proccess of fabrication of magnets ,to activate they use 300 v at 50 amps,,,so he just Made the oscillator starting with external energíy,,but the magnets keep the oscillations,👍
@@MrAcapela so you are saying that this is legit free energy stuff right?
❤❤❤SUPER BRILLIANT CONGRATULATIONS ❤❤❤
Thanks!!!
WE CAN COLABORATE IN FUTURE IF YOU CAN DESIGN AN 20 KW OVERUNITY ELECTRIC GENERATOR//
PLEASE ANALISE OPORTUNITY
Saludos una pregunta de q material se compone el eje q va en el centro del motor
Alloy aluminum brother
@@juvenalgonzalez8756
Since you're out of the socket, why doesn't the small motor you make the first move start? Shouldn't it work on it?
This is the most relevant question. Once it is "kickstarted" why doesn't the little kickstart motor (the thing that rotates the glass tray in microwave) keep going like all the other appliances plugged into same power board ??
Én úgy láttam, hogy lassan de tovább forgott amíg ki nem húzta
молодец!Наклейки подобрал правильные и правильно приклеил А если другие наклейки использовать, то наверно все 20 кило выдаст
adorei seu trabalho , quero comprar um , obrigado
Сделай сам.
Does it rotate?? Or it makes electricity without any part movement ??
Thanks for your video. Can I use a 4HP 3-phase motor instead of the 0.75KW 3-phase motor in your video?
Absolutely. Take your extension cord from the wall outlet, wrap it twice around the table holding any motor you like and plug your devices directly into it.
Formidable merci pour votre partage 👌👌👌
Good evening, I would like to know what type of material this central shaft is made of
its made of unobtainium...
Ya so the material can not be obtained
😂@@bunnykiller
I was sitting at the edge of my chair as this build was developing and it was all making sense to me, but I was perplexed as to how you were going to start an oscillation from a solid state generator. . . then you pulled out the synchronous motor and i about fell out of my chair, like watching the plot of a great movie unfold where there whole thing comes together. i know the connecting rod is the same material at the Liberty Engine 2 rotor. My question: can you shed any light on exactly what that alloy composition is? or a least a #### that represents that alloy? I have all the parts for my build but that. also, are the supporting brackets steel or aluminum? thanks!
The supports are made of steel. Today we have published another video in which we tell some information about the metal of the core
LO HE HECHO CON UN TUBO DE ALUMINIO Y NO FUNCIONA ...PUEDES DAR ALGUN DETALLE DE QUE MATERIAL USAR O DONDE SE CONSIGE ESE QUE USASTE 😢
Y EN LA CONEXIÓN CONECTAS LOS DOS CABLES MARRONES JUNTOS Y LOS AZULES EN EL OTRO LADO DEJANDO LA FASE DEL MEDIO SIN CONEXIÓN 😮???
@@FoxEcoit'll never be explained because it doesn't work. Great videos and thought provoking ideas though.
8:03
Самое интерестное ,это ручная динамомашинка которая типа возбуждает всю схему как волшебная палочка,тоесть мгниты с обмотками и начинается генерирование откуда-то свч аж 230в.и,работает даже пятидесятигерцовая болгарка,Тесла отдыхает!!!!
Are you an Eskimo? I have magic ice box I need to sell you 🛶
Видно как он при подьеме всей площадки стараеться поставить ее в определенное место и ножки закрывает руками.
In The proccess of fabrication of magnets ,to activate they use 300 v at 50 amps,,,so he just Made the oscillator starting with external energíy,,but the magnets keep the oscillations,👍
какое свч ,ты бредишь
@@АндрейКуликов-л5м это не мои слова ,сказанное было в ролике
Очень впечатляет спасибо,а какие магниты использавать можно неодиновые и наско веса они тянут притяжения?
Очень красивый фокус. Под столом мощная катушка, а све что сверху - вторичная обмотка вот и све
Нихера! У них в углу бочка с Плутонием стоит, которая облучает весь гараж и их город))
мощная катушка разогреет до бела стол покрытый металлом и сам девайс
Красивый удлинитель только зачем на нём столько лишних деталей хватило бы и фанерки с розеткой
...скорей всего литиевые аккумы в доске - основании
@@максимкиселёв-ш1ии я про это думаю, две доски аккумулятор внутри, доски с изолентой обмотаны, понтом красиво.
هل هذا حقيقة ام خدعه 😂
он творец, он так видит
@@максимкиселёв-ш1и ! Совершенно верно! В таких делах без прибомбассов не обходится!
Despues de varios años estudiando la teoria ifotonica de Jose Alfonso Hernandez , has ido capaz de hacer real su teoria. Lo más interesante, a parte de no tener piezas moviles, es la forma de arrancarlo, haciendo girar un toroide. En cuanto pueda lo replico y se lo pasaré al maestro. ESta es la energia libre que nos merecemos. Eres genial.
Фокус покус,энергия не исчезает и не находятся бесследно.😊
Ну, всё. Проблема с энергоносителями решена. Халявное электричество в каждый дом!😁😂🤣
Забавно, но это не работает так. Учите физику ребята😂. Но автор видео кое-где прокололся, а именно почему так называемый генератор пуска не стал вращаться самостоятельно после запуска всей конструкции. Хотя автор молодец большой он сделал генератор денег из воздуха) Вы просмотры и лайки а он денюшку с ролика.
Стол разделен на два потенциала и очень хорошо замаскирован. На 20:48 видна еле заметная полоска разделения стола. В ножках контакты. Старый фокус.
👏👍
Если посмотреть внимательно, то он начал вращаться, так же как в микроволновке, медленно. Пересмотрите, я сам вчера пересматривал и убедился что он начал вращаться.
Та физика о тпаразитов, даваемая в школе есть научный бред для оболванивая наших детей. НАУКА - для идиотов. Раньше была Тривия.
Absolutely awesome. You will see that nothing is rotating and producing electricity. Wow, I'm going to satellite my house🤣🤣🤣
Этот генератор нужно установить на грузовую тачку и по перону грузы возить!Красиво навещал лапшу на уши ,за ролик 👏.
Зачем на тачку ? На космолёт и за пределы галактики ! Электроников в провода запустил, а они там бегают и размножаются да ещё с такой скоростью, что исчерпать невозможно никакой нагрузкой.
Спасибо, я долго смеялся. Хорошая шутка!
Can you make a follow-up video where you plug the light in as well as the fan and pich the Power Generator up with the camera placed so one can see there are no cables under the Power Generator?
There are too many videos on FB showing "Free Power" that do not work.
If this works you should be able to demonstrate that quite easy
Excellent objection... If people believe this, then no wonder there are so many people who believe the earth is a flat plate... This world works by natural laws, not by magic tricks... (easy fun for the ignorant).. .
@@petarkostic3768exactly. "Free energy"... They don't know the 1st law of thermodynamics. They think it is possible to create energy from nothing or to have zero loss, zero friction, and so on 🤦🤦
it's all about getting clicks and earning money from the videos. They know there are a lot of curious people out there, and unfortunately most of them are also gullible.
Нобелевский лауреат, браво )
How long the magnet resist?
Я бы поверил , наверно , если бы он поднял платформу с генератором во время работы нагрузки , а так осталась большая вероятность фэйка.
100% фейк😂
You must get this out to the people.
Очередное изобретение , "вечного двигателя" 😊
Is it based on a Don Smith design? Seems high pwr for 1 set of ring magnets & 1 core. What's freq out? The power tool needs 50/60 Hz. Did you calculate the coils' resonant freq B4 assembly?
He tested it on a device that works on frequency need of 50/60 HZ , yes ?
Iluzija!🇸🇮♥️♥️♥️
Yes...
I like these videos very much. Amazing work. How do you think out such construction? Big energy companies won't like a mass production of such device. Would such device ever be on the market for sale? I am afraid that we we only see it on this video.
Much appreciation for the work making the device and video.
Once the patents expire they cannot prevent anyone from building them.
Bet legislators will modify patent laws before then though. Greedy as they are.
@@shigatsuningen read about this stuff 30 yrs ago but never seen it in action until now pretty simple and patents expired long ago.
@@perthcowboy2268 Good to know. Have seen quite a lot about Tessla's work and thought of things similar to this for a few years but never had time to do a build myself. Yet that is.
А еще был случай когда Мюнхаузен вытянул себя за волосы из болота...
May I ask if the strip metal is aluminum alloy or stainless steel?
İlginç, spiral makinesi çalıştığında lambada voltaj düşümü olmuyor. Nükleer tesisten alıyor olmalı şebeke elektriğini?
evet abi yoktan var etti 😂😂😂😂
Здравствуйте Либерти я смотрю все ваши изобретения вы гении своего дела хотелось бы узнать только один ответ что это правда. Я понимаю что секрет остаться за вами и есле это так то вы могли бы помоч миллионам людей сказав правду что это реальность а не фокус
Why tell trick when he gets clicks =$$$?
Єто лохотрон для просмотров видео.
Τα 10kw είναι αλήθεια και πραγματικό, αλλά θα χρειαστεί να δειται το βιντεάκι πολλές φορές ώστε να προσέξετε δύο και μόνο πράγματα για να προχωρήσετε στην κατασκευή αυτή, πολλά συγχαρητήρια σε αυτή την ομάδα των ανθρώπων ΜΠΡΑΒΟ ΣΑΣ. 10:26
@@МояПасека нет не лохотрон. дело в магнитах и волнах.
ПомочЬ ... к стати ... И это лишь фокус для просмотров ... Спроси у этого "мастера" - как удалось достичь 230 и при частоте переменки - в 50 герц . Он не даст ответ. Однозначно.
По простому-Это то же самое,что жить, постоянно питаясь своим говном..Великий Дэвид Копперфильд "рыдает"...
Hola, el anterior con el motor y alternador me convencia mas, este se ve aun mas sencillo y trabaja igual segun vi, pero los cortes de dicho video me dan a entender que se esconde algo.
Amigo repetir um progeto mecânico que usava imã e 2 bobinas com iman num veio cilindrico meso usando um motor esterno para o girar ele produzia 0 de enegia e foi copiado so ínfimo detalhe não dar para crer em tudo que montra nós videos só testando para saber vai que funciona algum deles se estiver próximo de um rio ou possua um poço com muita agua dar para oroduzir um gerador capaz de gerar uma boa energia
opino lo mismo.
hello sir, how to stop the generator? from producing the current
Remove the circle magnets
Bonjour super idée !
Comment faites vous pour l’arrêter ? De produire ?
How long does this energy remain at the same value?
여러분 전기와 자기에서 N과 S가 연속적으로 바뀌지 않으면 절대로 연속적으로 전기가 발생한다고 믿습니까? 혹시 원자력이라고 생각합니까? 속이는자와 속는자의 차이는?
Оригинальный станок, для сохранения энергий даже
Магниты помогают.😂🎉