I was worried far too much solder was used. I see you got the visible bridges but what about the possibility that bridging can happen under the IC far enough that its not visible?
You don't want a benzo, you want a beta blocker. That's what snipers *actually* use. Benzos are like drinking alcohol which is no good. In any case, unless you're a robot, nobody's hand is "steady" under a microscope so this complaint is moot.
@@_droid lol i been on benzos for 20= years trust me it will calm u down and keep your hands from shaking very very well if anything it may be too much relaxing causing delays in motor control called psychomotor impairment. Shakes only come during withdrawal so even being hammered on alcohol the hands should be way more relaxed state than non inebriated. back in the day they tried everything my uncle who was in the military 70s and 80s talked about them trying muscle relaxers at one point to see if that helped improve shot accuracy. he was in recon for almost 235 years before retiring i doubt he would make shit up because his military buddies were all there and all had stories of the same thing. maybe not in today's military they do such things but there was a time they would try anything to get an advantage. He said it was common in NAM to have new green recruits come into the country and get hooked on heroin and it was accepted they said that a soldier high on opiates is less likely to be afraid and it caused the men to do things they normally would of been to scared to attempt. The military didnt care about that im sure they didn't care about trying anything even if it was damaging to the soldier to win
Oh my God I'm going to come back to this one the list of what you did right and said versus the list of what you did wrong and said oh my God Only thing really I can think you said right is that reflow heat gun goes into standby mode when you put it in it stained and that's because it's got a magnetic read switch in the handle and little neodymium magnets in the stand... And watch out the hot air gun can burn you Let's see what else I like that you pre warm you're bored not your pre warmer though I will come back to this in outline lake everything wrong but And I say this with respect but if you ever read a datasheet for any of these components and looked at the reflow slash solder temperature chart for the part or any SMD cuz they're all pretty close but My speech-to-text is my location right now is Cappy location so I'll come back to this but I do hope you take what I say in this and my next reply
Thanks for the explanation. The preheater would perform the same sort of function as a hot plate, correct?
What kind of solder paste are you using?
Lead Free Solder = Sadness...
Nice bro! 😊
You definitely made it look like it isn't hard.
do we need lead? we have lots of flux...
Lead free is just a pain unless it gets banned I'll stick to leaded
I was worried far too much solder was used. I see you got the visible bridges but what about the possibility that bridging can happen under the IC far enough that its not visible?
Gravity prevents that from taking place I believe.
300 deg , air flow to half
nice vid , might want some lorazapam , snipers use benzos to keep steady aim , might help you to stable your hand...
I have the same, it would be useful to me too ...
You don't want a benzo, you want a beta blocker. That's what snipers *actually* use. Benzos are like drinking alcohol which is no good.
In any case, unless you're a robot, nobody's hand is "steady" under a microscope so this complaint is moot.
@@_droid lol i been on benzos for 20= years trust me it will calm u down and keep your hands from shaking very very well if anything it may be too much relaxing causing delays in motor control called psychomotor impairment. Shakes only come during withdrawal so even being hammered on alcohol the hands should be way more relaxed state than non inebriated. back in the day they tried everything my uncle who was in the military 70s and 80s talked about them trying muscle relaxers at one point to see if that helped improve shot accuracy. he was in recon for almost 235 years before retiring i doubt he would make shit up because his military buddies were all there and all had stories of the same thing. maybe not in today's military they do such things but there was a time they would try anything to get an advantage.
He said it was common in NAM to have new green recruits come into the country and get hooked on heroin and it was accepted they said that a soldier high on opiates is less likely to be afraid and it caused the men to do things they normally would of been to scared to attempt. The military didnt care about that im sure they didn't care about trying anything even if it was damaging to the soldier to win
Oh my God I'm going to come back to this one the list of what you did right and said versus the list of what you did wrong and said oh my God
Only thing really I can think you said right is that reflow heat gun goes into standby mode when you put it in it stained and that's because it's got a magnetic read switch in the handle and little neodymium magnets in the stand...
And watch out the hot air gun can burn you
Let's see what else
I like that you pre warm you're bored not your pre warmer though
I will come back to this in outline lake everything wrong but
And I say this with respect but if you ever read a datasheet for any of these components and looked at the reflow slash solder temperature chart for the part or any SMD cuz they're all pretty close but
My speech-to-text is my location right now is Cappy location so I'll come back to this but I do hope you take what I say in this and my next reply
You have issues.
What?
Leaded solder is the best………lead free just cracks and doesn’t hold. It’s garbage……….pure garbage.