Great video bud! You're awesome. Like everyone else I too got stuck at the long 10mm bit. Ain't nobody have a 6inch 10mm bit lying around so I had to stop work midway and put a special order in for a 6 inch 10mm . I think it might be worthwhile to mention the socket sizes in the description. Thanks for your work.
Hi bud, my super deep socket was from snap on, I’ve not heard of any other companies making these sockets but there are ways around it, you can tape 2 deep 10mm sockets together and it will work fine, the nuts aren’t done up very tight so it should still undo it fine
@@jackgross3140 ah ha!! Excellent idea with the 2 10mm take I together. I'm working on a slightly newer shape, theres no nut on bumper in the wheel arch, there was an 8m horizontal half way down the bumper, and the lights seem completely different to remove, I'll keep plucking away.
hi, please can you tell me how i can remove plastic arc on rear fender completely ? after the middle part is it fixed with a double-sided glue is it right? many thanks
Thanks for the video. I have an issue : When I put it back on, the plastic cover that goes over the wheel doesn't fit right, there's a gap between the panel and the plastic part. How could I fix this ?
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
Great video bud! You're awesome. Like everyone else I too got stuck at the long 10mm bit. Ain't nobody have a 6inch 10mm bit lying around so I had to stop work midway and put a special order in for a 6 inch 10mm . I think it might be worthwhile to mention the socket sizes in the description. Thanks for your work.
Great video! Straight to the point and easy to view what you are doing. Thanks!
Thank you for the positive feedback 😁
Hey! I want to change my rear bumper, but I need to buy a deep socket for the one in the trunk. Would a 12cm long socket be good?
@@Bogdan-gi9yx should be fine
Hey thanks for the great video! Just wanted to check if a 13cm / 5inch deep socket is deep enough?
That should be fine 👍
what's the nut size and how long the socket has to be in order to take it off at 1:40 and 4:15?
Both 10mm sockets, the one at 4:15 you will need an extra deep socket
@@jackgross3140 how deep at least? Thanks!
@@yauck1 it’s 4 inches deep approximately
I used the snap on 1/4 inch extra deep 10mm socket
Hi mate, how do I find a 10mm deep socket? I searched everywhere i.e. Halfords etc. thanks
Hi bud, my super deep socket was from snap on, I’ve not heard of any other companies making these sockets but there are ways around it, you can tape 2 deep 10mm sockets together and it will work fine, the nuts aren’t done up very tight so it should still undo it fine
@@jackgross3140 ah ha!! Excellent idea with the 2 10mm take I together. I'm working on a slightly newer shape, theres no nut on bumper in the wheel arch, there was an 8m horizontal half way down the bumper, and the lights seem completely different to remove, I'll keep plucking away.
hi, please can you tell me how i can remove plastic arc on rear fender completely ? after the middle part is it fixed with a double-sided glue is it right? many thanks
Just double sided tape for the rest of it, be careful not to bend the trim
Apply pressure outwards and wiggle up and down at the same time and the tape will be released
@@jackgross3140 many thanks
Thank you, I fixed my car without going to the garage ❤❤❤🎉🎉🎉
Thanks for the video.
I have an issue :
When I put it back on, the plastic cover that goes over the wheel doesn't fit right, there's a gap between the panel and the plastic part.
How could I fix this ?
Thankyou for the feedback! You may need to use some new double sided tape to re fix the arch trim back on after removal
Hey Great Video! I’m trying to do this for a friend but I’m having a problem finding that deep of a socket! How long is that thing?lol
Hi thank you for the feedback!😁 the socket is from snap on I can’t remember the exact size though unfortunately but it’s around 4 inches deep!
Thank you man ❤
Thanks 🙏🤲
merci beaucoup