Throwing this out there. Don't over pressure your rig. I started mine at 160 psi and blew the O rings in the center shaft and the bolt stop air nozzle had a massive leak. I talked to the techs at my local HPA shop and they tested it to 125 for its max PSI before failure and at 140 they couldn't even rack the bolt. Once I installed new O-rings and readjusted my Wraith to 100 PSI it shoots great.
@@xphile4938 Wraith stock compatible. Max psi is 110. At 115 you'll get about 5 shots then the O rings will blow. Sadly, this system only works reliably at 450 fps or 2.7 Joules.
I now have the Bolt M and Wraith in my JG Bar 10. I'm running a Maple Leaf Crazy Jet barrel, Action Army hop chamber, ML MR Hop bucking and the TDC mod. I've started experimenting with BLS .50g BBs and running at 3.4j. My shots are all over the place. Is there any way to control the amount of CO2 per shot? I may not have a good volume ratio.
The basic installation seems simple enough. I have the AA Zero trigger. Installation would be the same correct? Just remove the spring stop like in the stock trigger and so on? Rich is there anything different I should do? My gun has all AA parts.
i think for this to have successfull sales more clarification on compatibillity should realy be explored, what i mean by that is that no one really uses the std tm cylinder out side of 1j limit countries cos... well... its junk to be honest, that is why there are so many aftermarket cylinders on the market, and to be fair they all are pretty mutch a standard size, at least iv never had issues swapping ouy cylinder heads from edgi to sniper one for example but perhaps iv just been lucky lol, however what standard do the aftermarket cylinders follow is the big question hear, outside the us the jg bar10 wouldent be used as a standard as there are far better (and either cheeper or equal to) options out there (eg action army t10 or t11, or spend a bit more ang for an sfc vsr) but it be nice to know what standard say action army or airsoft pro or edgi or tnt or... well you get the picture lol
The Bolt M is fully mechanical where the Bolt is electromechanical. Both are great systems and will serve mostly the same function. We have been able to get the Bolt M to work with a few more sniper platforms like the Silverback SRS and the Ares Striker.
Thanks Rich. I appreciate what you guys have done for the airsoft community
I always wanted to do this to my Sniper Rifle. Loving these type of videos. Great job!!
Throwing this out there. Don't over pressure your rig. I started mine at 160 psi and blew the O rings in the center shaft and the bolt stop air nozzle had a massive leak. I talked to the techs at my local HPA shop and they tested it to 125 for its max PSI before failure and at 140 they couldn't even rack the bolt. Once I installed new O-rings and readjusted my Wraith to 100 PSI it shoots great.
Thank so max is 140. Are you using the wraith c02? Which regulator?
@@xphile4938 Wraith stock compatible. Max psi is 110. At 115 you'll get about 5 shots then the O rings will blow. Sadly, this system only works reliably at 450 fps or 2.7 Joules.
@@GhostStalkerActual looks like I won't be buying it then that will not cut it at my field with a 650 fps limit. I prefer spring anyways
Great vid!
So it uses the stock trigger mech? Neat!
Am I doing something wrong because if I raise the pressure past 120 psi the rifle will fire as I push the bolt forward without pulling the trigger
Did you ever fix this? Seems to be a common issue
I now have the Bolt M and Wraith in my JG Bar 10. I'm running a Maple Leaf Crazy Jet barrel, Action Army hop chamber, ML MR Hop bucking and the TDC mod. I've started experimenting with BLS .50g BBs and running at 3.4j.
My shots are all over the place.
Is there any way to control the amount of CO2 per shot? I may not have a good volume ratio.
I have an Ares M200/EDM200 that has a vsr10 style bolt assembly.
Do you think it is possible to make this work in that rifle?
Nice!!! Now make a Hydra nozzle for a Sten gun!!!
The basic installation seems simple enough. I have the AA Zero trigger. Installation would be the same correct? Just remove the spring stop like in the stock trigger and so on? Rich is there anything different I should do? My gun has all AA parts.
Doesn't work with 90 degree triggers
So along as the cylinder is vsr 10 compatible then you van fit the bolt m?
Nooo… i just bought the jg bar 10.. hoping it can fit on my vsr 10.. and its not
Will this also work with the wraith co2 adapter
Is it compatible with the wraith co2 adapter?
My only question is can this fit in a desert tech SRS
oh this shot at the end was louder no ??
So what makes the bolt m so special? I didn’t even know that a new hpa engine for bsr was released.
OP Airsoft no battery. HPA sniper with no line on your back and no electronics.
So I have a agm l96 and I wanted to throw a hpa bolt in it specifically what should I do
Maybe someone can help me out i recently wanna convert my Action Army T10 to HPA and was wondering what bolt i need?
i think for this to have successfull sales more clarification on compatibillity should realy be explored, what i mean by that is that no one really uses the std tm cylinder out side of 1j limit countries cos... well... its junk to be honest, that is why there are so many aftermarket cylinders on the market, and to be fair they all are pretty mutch a standard size, at least iv never had issues swapping ouy cylinder heads from edgi to sniper one for example but perhaps iv just been lucky lol, however what standard do the aftermarket cylinders follow is the big question hear, outside the us the jg bar10 wouldent be used as a standard as there are far better (and either cheeper or equal to) options out there (eg action army t10 or t11, or spend a bit more ang for an sfc vsr) but it be nice to know what standard say action army or airsoft pro or edgi or tnt or... well you get the picture lol
Can i make a straight pull mod with the bolt m?
No
Is the bolt M compatible with a SSG96 with some modifications ?
is this compatible with the echo one psr?
Did you ever purchase this for the echo 1 if so which thread did you go with the Tokyo Marui or jg bar
I did not understand how the original trigger operate the air system (without a solenoide).
Works like a normal bolt
Still waiting for the Bolt for the zero trigger....
It can.. i just try it
can i just this this bolt assembly and throw it in
Hey does anyone know if this would work on a type 96 rifle
With this work with a Zero trigger.
Yup
O what's the difference between the "BOLT" and the "BOLT M" and which is better?
The Bolt M is fully mechanical where the Bolt is electromechanical. Both are great systems and will serve mostly the same function. We have been able to get the Bolt M to work with a few more sniper platforms like the Silverback SRS and the Ares Striker.
@@WolverineAirsoft Would either of the systems be compatible with the Action Army AAC T10 DE?
will it fit mod24?
is it good for ssg10??????
Will it work with 90⁰ trigger?
It work
Can i use a 90 degree sear?
Yes
Will this work with a zero trigger
No
Wraith stock compatible?
UpangtheMan is it?
When is the BOLT M going to be released?
Theo Lee already released to retailers
Stole Mancraft’s whole flow