I have no idea how to use these things and this video didn't help - it's just describing the features like an infomercial - if I look for a video titled how to use your... it should be assumed that I already own it so I don't need a sales pitch, I need a step by step walk through
Have you even watched the video? It pretty much describes how to use all of the functions. If you don't know how to use studio lights at all, there's a ton of videos about that.
You connect the trigger to the show mount on the top of your camera and you turn the silent shutter off on your camera. Then you adjust the intensity of the flash on the actual strobe. Start with it low. They are super powerful if you have them above the lowest settings.
Hi. I can't seem to consistently get this strobe to fire with the included remote. In my Nikon Hot shoe sometimes it fires every shot, other times it seems to fire every other shot (single shot). Right now I can't get it to fire at all. The Flash works fine when I click the test button on the strobe. But won't fire at all clicking the remote.
@@Brenby unfortunately not exactly. I discovered that if I held the remote right up to the back of the strobe, it will fire. But ONLY if I held it on the right side, not on the left. And only from like two feet away max. Ultimately I just sent it back and ordered a godox kit as I didn't feel like spending time or money to see if the remote was the issue or the strobe. Plus, trying a different brand would let me know if it was my hotshoe. It wasn't, the godox works great. Sorry.
@@Shootingthegalaxy dont be sorry! Thanks for your response. We can surmise that the remote is cheaply manufactured and prone to failure. I'm thinking of going your route as well.
The small elastic banded diffuser shown at the bottom far left at 1:06 is not large enough to go onto the big end of the reflector. I can't figure out what this is used for, where to place it. Can someone help me out? thanks. I do like this economy strobe. It's great.
My brand new Neewer Vision 4, test button doesn't work just beeps, and it doesn't fire the flash. other buttons work well. Any idea or shall I return it.
I have 2 of these - they are great! Also can shoot HSS through the slave system. 2.8F anywhere from 1000s-4000s @ ISO400 YOUNGNO YN568EX Flash on 1/8 power Neewer on 1/4 power. Pull out bounce card aim flash at sensor on Neewer & BAM HSS....try it & experiment. Trust me it works!
@@lesleylara8544 basically, what is is saying is instead of triggering the strobe directly, trigger a Speedlite with HSS and set this stone in slave mode. As a result, you can shoot over 1/160s.
@ThePalliz, I tried doing same but seems like it do not work the way you explained. I checked all the settings yet still my camera curtains closes fast and results to black image! I used my YN 568exii as master flash to trigger vision 4.
Hi, why if I go over shutter 250 it has half of my image blacked out??? How do I change that? Shutter speed cannot go over 200-250, how to get HSS up on this trigger?
Anything over 250 is considered high speed sync. This strobe isn’t HSS. 200 is good enough to capture any moving object. Just set ya camera at high speed continuous shooting mode. And it shall work fine!
Hello this is helpful. Where can I find information on how to setup with other speed light or strobe? If I’m asking the right question wanting to buy 2 more lights and sync. Or use as an optical slave for other strobes
I received mines after the new year and the battery life lasted very long seeing that I didn't always use it. But when I tried to charge it doesn't work. Ive been charging this for days now, the green light indicator would come as if its fully charge but when I put the battery back into the strobe it just beeps constantly warning me that the battery is low. Would I need to replace the charger or battery ?
@@NeewerOfficial thank you for getting back to me. I used my vision 5 on group A and Vision 4 on Group B..the only drawback is you don't get to see what settings are on Vision 4 on the remote, it just beeps and changes blindly
@@timelesscreations777 You are welcome:) Do you mean that the remote control can only flash V4 but cannot adjust the other settings of V4? This is actually normal, because V4 is an earlier model, and its own remote control does not support remote power or other adjustment settings.
I have the yn560 - tx trigger +RF605N (connected to the sync port). You can only fire the strobe, not control the power level. You will sill have to do that manually
These are rebranded Visico units. Buy a Visico VC-801 TX wireless controller and you can adjust power and turn the modelling lamp on and off remotely. I bought mine from Lencarta in the UK.
@@Dylan-bj5ry thanks for this tip ... had I trusted my guts at first then, I would have bought it instead of the Yongnuo trigger. Its not complete loss cause I adjust my speed light remotely n manually adjust the neewer strobe
wow, great support...thought this is a " Neewer Channel", which cares about customers...think, i send this Item back, and buy only Godox in the next future
does the trigger work on a film camera ?
I have no idea how to use these things and this video didn't help - it's just describing the features like an infomercial - if I look for a video titled how to use your... it should be assumed that I already own it so I don't need a sales pitch, I need a step by step walk through
Have you even watched the video? It pretty much describes how to use all of the functions. If you don't know how to use studio lights at all, there's a ton of videos about that.
Same lol this video is way too advanced
You connect the trigger to the show mount on the top of your camera and you turn the silent shutter off on your camera. Then you adjust the intensity of the flash on the actual strobe. Start with it low. They are super powerful if you have them above the lowest settings.
Dont buy sht u dont know about or they should be a manual at the box read it!
If that's the solution then why does this video exist?@@LegoAventuras1718
Hi. I can't seem to consistently get this strobe to fire with the included remote. In my Nikon Hot shoe sometimes it fires every shot, other times it seems to fire every other shot (single shot). Right now I can't get it to fire at all. The Flash works fine when I click the test button on the strobe. But won't fire at all clicking the remote.
Have you figured out the issue yet? I'm experiencing the same...
@@Brenby unfortunately not exactly. I discovered that if I held the remote right up to the back of the strobe, it will fire. But ONLY if I held it on the right side, not on the left. And only from like two feet away max.
Ultimately I just sent it back and ordered a godox kit as I didn't feel like spending time or money to see if the remote was the issue or the strobe. Plus, trying a different brand would let me know if it was my hotshoe. It wasn't, the godox works great.
Sorry.
@@Shootingthegalaxy dont be sorry! Thanks for your response. We can surmise that the remote is cheaply manufactured and prone to failure. I'm thinking of going your route as well.
same..
How to connect it to my Sony a7iii? I cannot understand whatsoever
The small elastic banded diffuser shown at the bottom far left at 1:06 is not large enough to go onto the big end of the reflector. I can't figure out what this is used for, where to place it. Can someone help me out? thanks. I do like this economy strobe. It's great.
Take your time with it- it DOES fit. I had to try a few times.
Does anyone know if this shoots fairly ok for outdoor locations?
It’s shoots great I own 2 of them
Thanks, I needed this. I just received mine in mail today after getting it on prime day for the low 😁
THANKS SO MUCH I ENJOYED YOUR MODEL, YOUR ACCENT AND ESPECIALLY THE INFORMATION.
My brand new Neewer Vision 4, test button doesn't work just beeps, and it doesn't fire the flash. other buttons work well. Any idea or shall I return it.
Can you please tell me if I can use a smaller power than 1/64, is there a way to make it like 1/128? Thank you.
Second this
@@Alfiefisher. sorry, second what?
Use an ND filter to drop a stop.
@@DobbsyLondon nd filter for the strobe ,right?...thank you for you answer.
@@travelonhistory ND filter for whatever you're shooting with. Ideally the lens.
I have 2 of these - they are great! Also can shoot HSS through the slave system. 2.8F anywhere from 1000s-4000s @ ISO400 YOUNGNO YN568EX Flash on 1/8 power Neewer on 1/4 power.
Pull out bounce card aim flash at sensor on Neewer & BAM HSS....try it & experiment. Trust me it works!
Can you explain a little more beginner friendly?
@@lesleylara8544 basically, what is is saying is instead of triggering the strobe directly, trigger a Speedlite with HSS and set this stone in slave mode. As a result, you can shoot over 1/160s.
I have 4 yn600ex rt flash guns . Can I use them with these lights?
@ThePalliz, I tried doing same but seems like it do not work the way you explained. I checked all the settings yet still my camera curtains closes fast and results to black image! I used my YN 568exii as master flash to trigger vision 4.
Hello, does anyone know how to sync the trigger, I have tried everything, and it does nothing, help!!! 😢
Hi, i have this strobe with a 818tx trigger... How can I turn on The modeling lamp from The 818tx????
My sync port broke. What would i need to purchase to sync my Canon Mark 11 7D? The trigger that came with my vision 4 is not working.
Can you turn the light one without manually pressing the button?
That's my question.
Recently got and charged the battery, however when I out the battery in it won't turn on
How do I use the trigger remotely with a sony a7riii? Do I need to buy something else to make it work?
Impact VC-500WLXMT Wireless it will work for it ! I have a Canon T6s and it works great for me!!
@@marcusmccurtis2660 Thank you so much for the help, I will order it today. Much appreciated!!!
@@heisenberg9616 no problem at all please visit my IG: BLUE VISION PRO PHOTOGRAPHY All done with the VISION 4
Is there a trigger with a LCD display to be able to change power from the trigger?
Thanks!! Love this
I have the canon rp and I need a trigger that works. Any suggestions?
Hi, why if I go over shutter 250 it has half of my image blacked out??? How do I change that? Shutter speed cannot go over 200-250, how to get HSS up on this trigger?
Anything over 250 is considered high speed sync. This strobe isn’t HSS. 200 is good enough to capture any moving object. Just set ya camera at high speed continuous shooting mode. And it shall work fine!
Hello this is helpful. Where can I find information on how to setup with other speed light or strobe? If I’m asking the right question wanting to buy 2 more lights and sync. Or use as an optical slave for other strobes
Hi Alisha Barnes, you can send an email with your questions to service@neewer.com, our colleagues will help you!
I don't understand how to get it to work with my Nikon D850 :( I am new to strobes and so frustrated
How do I manually reset the light
I’m not sure why but the bulb permanently on and it won’t flash? Someone help please!
Hi Jacob B Mathis, you can send an email to service@neewer.com, please kindly attach some pictures and video, our colleagues will help you!
is this strobe compatible with canon r5?
Yes, it is compatible with canon R5.
I received mines after the new year and the battery life lasted very long seeing that I didn't always use it. But when I tried to charge it doesn't work. Ive been charging this for days now, the green light indicator would come as if its fully charge but when I put the battery back into the strobe it just beeps constantly warning me that the battery is low. Would I need to replace the charger or battery ?
Did u find the solution ?
Will this work with the canon 6d mark ii ?
Is this strobe cmpatible with canon 5D mark iv
I have the NEEWER VISION 5. I just had one of these and was wondering what my trigger from The Vision 5 work with the Vision 4?
The V5 trigger has three compatible models: Canon, Nikon, Sony, they can all be used to trigger V4.
@@NeewerOfficial thank you for getting back to me. I used my vision 5 on group A and Vision 4 on Group B..the only drawback is you don't get to see what settings are on Vision 4 on the remote, it just beeps and changes blindly
@@timelesscreations777 You are welcome:) Do you mean that the remote control can only flash V4 but cannot adjust the other settings of V4? This is actually normal, because V4 is an earlier model, and its own remote control does not support remote power or other adjustment settings.
How do a set a rear curtain flash?
Wonder if I could attach yongnuo triggers with the cable and adjust the flash power without moving to and from the flash???
I have the yn560 - tx trigger +RF605N (connected to the sync port). You can only fire the strobe, not control the power level. You will sill have to do that manually
These are rebranded Visico units. Buy a Visico VC-801 TX wireless controller and you can adjust power and turn the modelling lamp on and off remotely. I bought mine from Lencarta in the UK.
@@Dylan-bj5ry thanks for this tip ... had I trusted my guts at first then, I would have bought it instead of the Yongnuo trigger. Its not complete loss cause I adjust my speed light remotely n manually adjust the neewer strobe
@@Dylan-bj5ry whats about vc 818 tx? Can that work too?
@@TheSocialjerry I spoke to the guys at Lencarta who said they had been unable to get the 818tx to work with the visico (vision ) 4.
I have a Godox ProN trigger. Will this Neewer Vision 4 Mono light work with that? I haven't been able to make that happen yet.
No, Vision 4 cannot work with the Godox trigger.
@@NeewerOfficial I'm disappointed, but thank you for the reply.
Hello! i got a V4 but it came without the manual...can someone please share a trustful Download-Link? many thanks in advance!
wow, great support...thought this is a " Neewer Channel", which cares about customers...think, i send this Item back, and buy only Godox in the next future
How can you see what your battery level is?
Yes
When the battery reaches very low it will show on the screen
has this flash S1 mode ? for optical shoot
Does anyone know how to change the trigger code on both. It didn't work for me
do you mean the channel of both the trigger and the light? Just make sure the channel of the trigger and the light are the same.
hagan ese tutorial en español por favor!!! gracias pude arreglar el rollo que tenia!!
Does this have high speed sync
I need help connecting this monolight to my Canon Rebel T7. Anyone?
Did you ever figure it out??? I need help with this too.
Buenas noches, cual es el precio de ese flash.
En Amazon es como $289 ahí lo compre y es genial el flash!
@@Lupercio222 pana y el receptor no te da problemas???
Does it beep when it’s low on battery?
yes it does, continuously until you turn it off.
i love u, thank u.
I'll be honest, the lack of (inbuilt) HSS is really a deal breaker .
this is Soo helpful thanks
Please made a video light with a lithium ion battery!
V4 does come with a lithium-ion battery :) Please take a look at 1'21'', you will see how we can charge the battery.
7:04
Hello, I can't seem to turn off multi-flash mode. It will fire 3 times or more no matter what I do. Can anyone help?
Aucune explication en français .. meme dans la notice produit .. bref n importe quoi ..
does the trigger work on a film camera ?
good morning I wanted to know if the "neewer vision 4" was compatible with other triggers, such as the "neewer N1T"??
no, Vision 4 is not compatible with other triggers.
@@NeewerOfficial iNCORRECT.
@@therookiefisherman5234which remote do work with V4?