For you people who want or are interested in this engine, I have it in a Top Flite P-51d 60 size model and it gives it plenty of power. The pane weighs in between 11 and 14 lbs, and it still can reach speeds of nearly 90 mph. Now the video says you may use the props listed. SOME of those props are correct. You can use a 14x10, 15x6, 15x10, 16x6, 16x8, and a 17x6. These I believe are the suggested props from the manual, however I may be missing one. You can also talk to your local hobby guy about it.
I fly a 84" Cessna 182 all up weight about 12.5 lbs NO issues at all, I run a MA 15x10x3 and turn 8200 pretty easy, I am well aware the 16x8x2 would give better power, but its not needed and the ground clearance of the 3 blade stops me from chipping tips on landing
Is the coil inside the connector for the spark plug actually required? The connector on my new DLE 20ra does not connect properly when the coil is inside but fits well without the coil.
How tall from crankshaft centerline to top of cyl. head? Over plug and wire? How wide at head? Is there a slim side muffler available (and whose?) Thanks.
Hi James! Where can I get carbs for 10-20cc 2 strokes like the one shown in thevideo? I dont have local model engine sellers so the internet is my only option. Thanks!
The video started off great but it turned out to be a waste of time. You should’ve had the physical engine in your hand to demonstrate all the details about it. This will be my first gas engine and I’m trying to find out if I need side exhaust or rear exhaust and that wasn’t even mentioned.
For you people who want or are interested in this engine, I have it in a Top Flite P-51d 60 size model and it gives it plenty of power. The pane weighs in between 11 and 14 lbs, and it still can reach speeds of nearly 90 mph. Now the video says you may use the props listed. SOME of those props are correct. You can use a 14x10, 15x6, 15x10, 16x6, 16x8, and a 17x6. These I believe are the suggested props from the manual, however I may be missing one. You can also talk to your local hobby guy about it.
I fly a 84" Cessna 182 all up weight about 12.5 lbs NO issues at all, I run a MA 15x10x3 and turn 8200 pretty easy, I am well aware the 16x8x2 would give better power, but its not needed and the ground clearance of the 3 blade stops me from chipping tips on landing
Hi do you have a DLE Carb on it or Walbro please?
great video thanks, just purchasing this engine.
Great video, thank you for explain and presentations of this engine. Appreciate it 👍
where can we find the video of you trying it on the extra
Looking to pick this engine up for my TopFlite P-47 1/7 63". Been watching a few birds being built on the RCSB forums.
Good idea or bad idea to replace my OS 1.20FS on a ESM 71" Skyraider??
Is the coil inside the connector for the spark plug actually required? The connector on my new DLE 20ra does not connect properly when the coil is inside but fits well without the coil.
I hv 3 of these models , runs really great & purs like a cat .
It doesn’t come with mount stand offs so what make/model engine mount do we need?
im building a great planes extra 300s 60 right now, could you do a video of your dle20cc engine installation, would help me alot
How tall from crankshaft centerline to top of cyl. head? Over plug and wire? How wide at head? Is there a slim side muffler available (and whose?) Thanks.
can i used this 20cc in my super falcon 120 ???
You can solve the throttle problem with a bell crank
Can you run none ethanol?
Hi James!
Where can I get carbs for 10-20cc 2 strokes like the one shown in thevideo?
I dont have local model engine sellers so the internet is my only option.
Thanks!
can the head be turn to the carb so the mufler be at the carb side ....?????
The video started off great but it turned out to be a waste of time. You should’ve had the physical engine in your hand to demonstrate all the details about it. This will be my first gas engine and I’m trying to find out if I need side exhaust or rear exhaust and that wasn’t even mentioned.
i am thinking of top flite 182 Cessna will that engine work
Its Made in China... Quality = ? Durability = ? Consistency = ? Reliability = ?
just got one fore my seagull snafoo
Made in China, single bearing crank.
Yea, just go with Zenoah Japanese engines.
Love my zenoahs, but my planes all lose 2 lbs when replacing them..
Zenoah...much better....
no it has two ballbearing not one, the rcg 15cc has only one ballbearing,
@@RPM-wd9rb you sir have a foul mouth and I say get lost
POTTY MOUTH has no place here. @@RPM-wd9rb
Much too long from back to prop hub for most smaller models!!
Um...Umm...Umm...Um..Umm...Umm...Umm..UM..UMM..UMM..STAY HOME. that is my Suggestion.
D Trump is God