closed loop boost converter design simulink and control Matlab Simulink

In this video, closed loop boost converter design simulink shown. First see the closed loop boost converter design in constant dc voltage source then a variable source is applied and see the result.
boost converter using pi controller design. Simulink Matlab 2016
Music: www.bensound.com

[@ShivamMishra-ch3sj]

Great video. Can you please make a video on how to find the gain values, (Kp, Ki etc). Also the L and C values.. I am working on a luo converter

[@himanshupatel9091]

thank you so much... very fine video..i really like this

[@Stay.Strong.Keep.Moving]

Thanks for the useful video.

[@muhammadshehbazaslam4549]

Will the parameters will change if I maintain constant 50?
Or same??

[@mukhlisikhsandy9142]

why did you add 1/20 gain ??

[@learningexploration4608]

Good presentation

[@nihalbayramoglu6523]

Can we use this closed loop for buck and buck-boost converter too? Please help me?

[@denizertas4284]

hi, can you explain how pi control working ? how you can draw this block diagram ?

[@andac4563]

Great video. It's very helpfull, thank you. But i have one question. Why did u put a gain before pid that divide the error with reference value?

[@aishwaryapatra5843]

@technotrip very nicely explained.. Can you please provide me the simulation.

[@boutebbaokba358]

Hi it verry nice work but i want the the following parameters
values for :Capacitor , Resistor , indector, E .and The
switching frequency for the PWM .

[@dindu1751]

Nice video. Can you use PI control for single active bridge dc dc converter

[@abhianosh604]

Sir can we use Same PID controller design for buck converter

[@sindbad184]

How can You tuned the KP and Ki ??

[@javierguevara9872]

Hello, could you say what is your input voltage? Thank you

[@manasguttal7874]

Can u please share how did u tune PI controller?

[@saikrishna-ie1xf]

please reply.. .how to tune the PID controller...

[@hinakadeval4124]

Would like to buy model.
. Can u give your detail ?

[@hossammohmed4154]

would u help to apply the design for SEPIC converter using pi controller but in PSIM software

[@bilalanwar149]

thanks for share.
i want load changing during 0-5 sec like 50 ohm and 5-10 sec want double, like 10 ohm. so how can i set? can you guide me thanks

[@talaljutt1594]

video is very cool but i found an error in this project when i m running it..error is(The sample time after propagation is [0, 1]. Enter a discrete sample time in 'lcsproject/PID Controller/Integrator'.) i do the same work as you have done can you please help me

[@shahabijan]

go to the PID block and put sample time 0.5e-6 instead of -1 (inherited).

[@ajaysivakumarn]

Thank you bro

[@sametkaya4653]

hey do u know idea controller in noninverting converter thanks

[@sushrutshailendrawasnik8302]

I made some changes in this circuit
Now the simulation time has been increased...does 1% in 6-7 minutes
Any help?

[@raisinghrajput3614]

Can anybody help me, that if I implement this circuit practically, from where I give reference 20V?? Because that is what I ultimately want.

[@jagrutirathva3127]

from dsp we can get 5v and with help of om amp we can achieve this

[@vandanajadhav6307]

Controlled voltage value plz sjow

[@fckrfckrfckr]

I think your fsw isn't 25kHz. Please have a look

[@gudellithrishool2249]

Super bro

[@achourabderraouf3181]

please i need your help in buck boost simulation model with PI regulator

[@georgeghimire4483]

hey didi you do it. I am doing a project on buck boost. if you had already done plz give me some idea

[@baluumesh9091]

How to implement hardware for pi controller

[@selvamary4404]

Design calculation please

[@DoudouBtb]

Hi it is a verry nice work but i want the the following parameters
values for :Capacitor , Resistor , indector, E .and The
switching frequency for the PWM . thnx

[@ihssanall-issa25]

would u help to apply the design for controller the (UPFC) unified power flow controller in matlab simulink