6:55 Be carefully with moving the desoldering iron on the pad so much. It happened to me, that I cut the trace to the pad because of too much moving and force to the iron. 🤦♀️ It depends on the board, some have very tiny traces.😊
you are right. if we rotate the desoldering tip while pressing hard on traces, it may damage the traces. or if the temperature is too high, it may result to separate the bonding of traces. otherwise, using desoldering tool, it is necessary to rotate the pin in the cylinder to free-up the solder to flow easily, otherwise if the solder remains in the gap between pin and cylinder, it will make dry joint and it becomes difficult to remove it in second attempt
yes sir as you mentioned the board quality, that is also a big point to be kept in mind while rework moreover, soldering temperature and soldering time matters a lot,
Well done, sir. Each type of component requires a specific desoldering strategy. I use the word "strategy" with purpose, because prior thought and planning are required to prevent additional damage. One should not rush to begin. I have not encountered a device package such as this. But, I may have approached it slightly differently. (We all have our own skills.) For those folks that do not have a desoldering gun... Because the IPM's pins are quite long, I may have attempted to desolder the outer pins one at a time and just gently bent them up. This may have freed up enough space to desolder the inner pins without the use a gun. Another thought... To protect the new part from over heating when installing it... On the long pins, place a blank alligator clip (no wire attached) next to the chip's body to act as a heat sink. Because the pins are so long, the extra mass may protect the chip without increasing the soldering dwell time. Trial and error are necessary, here. There are special alligator clips that have a flat bill and no teeth. They are better, for this purpose. I also discovered your method of staggering the pins, when soldering, to reduce the heat intensity in any one location. I can testify that this method works well. HTH. Another great video = thank you. Cheers, my friend!
Teşekkürler efendim verdiğiniz bilgiler için. Bundan önceki 2 video yu Türkçe altyazı olmadığını belirtmek isterim. Hayır ve sağlık dolu günler dilerim.
Very good video, I have a pistol that fires ONLY with a very good vacuum and everything like that, as you say. What I do next is to put a fire again, so the crack that happened to be in the hole in the boards I have is from the company I bought it from. my second post-apocalyptic pistol
Sir, I am troubleshooting one of my emergency lighting circuit, while switching ON the power the relay is not getting changed over due to voltage present at relay coil followed base voltage available at transistor. Base voltage has to withdraw while power in ON condition. Its not happening. Due to wat reason it is like this.
boa noite irmão. muito bem-vindo, não há folha de dados disponível scm1246mkf, então não tenho certeza sobre a diferença entre scm1246mkf e scm1246 mf. por esse motivo não posso dizer exatamente. mas acho que ambos funcionarão da mesma forma
@@HaseebElectronics desoldering item is working spontanely. It doesn't have any buton as seen. Is it continously vaccuming ? Or is there any buttun ? Or any other way?
@karisikpekmez6850 it has a push button on grip. Its desoldering nozzle heats up We place nozzle on desoldering point When solder melts Then the push button on grip is pressed. Its vacuum pump starts and complets its process
وعليكم السلام أخي، من الصعب جدًا بالنسبة لي أن أتحدث باللغة العربية لأنني من باكستان. أنا أتكلم العربية قليلا. لكني أقوم بإضافة ترجمات إلى مقاطع الفيديو الخاصة بي، يمكنك تشغيل الترجمات بالضغط على زر CC الموجود على شاشة الفيديو على هاتفك واختيار الترجمة العربية أطيب التحيات والشكر الخاص
Students and hobbyist would not have the budget for these expensive vacuum pumps, just mask off the board and use a solder sucker as an economical alternative.
6:55 Be carefully with moving the desoldering iron on the pad so much. It happened to me, that I cut the trace to the pad because of too much moving and force to the iron. 🤦♀️ It depends on the board, some have very tiny traces.😊
you are right.
if we rotate the desoldering tip while pressing hard on traces, it may damage the traces.
or if the temperature is too high, it may result to separate the bonding of traces.
otherwise, using desoldering tool, it is necessary to rotate the pin in the cylinder to free-up the solder to flow easily,
otherwise if the solder remains in the gap between pin and cylinder, it will make dry joint and it becomes difficult to remove it in second attempt
yes sir
as you mentioned the board quality, that is also a big point to be kept in mind while rework
moreover, soldering temperature and soldering time matters a lot,
thank you, I recognize not only a professional ability, but also a teaching ability, useful to all people of good will. Greetings from Italy.
You are welcome!
humble thanks for your valueable words
Well done, sir. Each type of component requires a specific desoldering strategy. I use the word "strategy" with purpose, because prior thought and planning are required to prevent additional damage. One should not rush to begin. I have not encountered a device package such as this. But, I may have approached it slightly differently. (We all have our own skills.) For those folks that do not have a desoldering gun... Because the IPM's pins are quite long, I may have attempted to desolder the outer pins one at a time and just gently bent them up. This may have freed up enough space to desolder the inner pins without the use a gun. Another thought... To protect the new part from over heating when installing it... On the long pins, place a blank alligator clip (no wire attached) next to the chip's body to act as a heat sink. Because the pins are so long, the extra mass may protect the chip without increasing the soldering dwell time. Trial and error are necessary, here. There are special alligator clips that have a flat bill and no teeth. They are better, for this purpose. I also discovered your method of staggering the pins, when soldering, to reduce the heat intensity in any one location. I can testify that this method works well. HTH. Another great video = thank you. Cheers, my friend!
Love it ! Good tools + good skills + patience = good results :-)
That's an excellent demonstration for which I've been looking for. Thank you Haseeb!
A very successful work. I am grateful to you for sharing your valuable experiences with us. God bless you
It's my pleasure
mashallah bohat achey se guid krte hain
thanks
it is my pleasure
اللهم صل وسلم وبارك على سيدنا محمد وعلى اله وصحبه اجمعين شرحك جميل يا هندسه
Nice job! I really need to invest in a good desoldering tool. Thanks for sharing.
Beat regards
Yes. Perfect tools for a perfect job.
Without having tools, it maks hard to fix anything perfectly
You are giving pure knowledge to us thanks
Thanks and welcome
Very helpful videos👌👍❤️
Watching you from Bangladesh.❤❤
most welcome
جزاك الله خيرا ، عمل لحترافي ونصائح في محلها ،
Very useful video good work brother
beautiful material 👍👋
best regards
Excellent thanks for sharing this informative video keep sharing
thanks a lot
Congratulacions, Very good
بارك الله فيك
Great work. Greetings from México
super job sir, from europe slovakia
best regards and special thanks for your valuable comment
Very very nice video sir thank you
Informative video. Thank you so much. God bless you.
So nice of you
thanks very much for sharing your knowledge...god bless.
Teşekkürler efendim verdiğiniz bilgiler için. Bundan önceki 2 video yu Türkçe altyazı olmadığını belirtmek isterim. Hayır ve sağlık dolu günler dilerim.
saygılarımla. evet son 2 video çevrilemedi. çünkü bu aralar çok meşgulüm. Bu videoları mutlaka çevireceğim. geç kaldığım için özür dilerim. selam
وعَلَيْكُمْ اَلسَّلام وَرَحْمَةُاللهِ وَبَرَكَاتُهُ
Thank you for this tutorial
I need to know how led drive work and how to know led consumed current
Perfect 👍 ❤
Very good video, I have a pistol that fires ONLY with a very good vacuum and everything like that, as you say. What I do next is to put a fire again, so the crack that happened to be in the hole in the boards I have is from the company I bought it from. my second post-apocalyptic pistol
Muinto obrigado cordial mente José Carlos
melhores cumprimentos e agradecimentos especiais
Good job 👍🏻 ❤❤❤
thanks a lot
Nice Sir 👌👍
Thanks and welcome
Very nice ❤❤
Many many thanks
Mashaallah Good work
thanks a lot
Great Work
thanks a lot
Sir good evening,mosfet 09N70P whats the alternate if no available.thank you
Very nice. But sir how to check six signal from MCU to drive IPM.
Best regards
I will explain in upcoming session
I use your method but some times when the pins stucked with some solders i use hot air and flux to remove the IPM.
Sir,
I am troubleshooting one of my emergency lighting circuit, while switching ON the power the relay is not getting changed over due to voltage present at relay coil followed base voltage available at transistor. Base voltage has to withdraw while power in ON condition. Its not happening. Due to wat reason it is like this.
جزاكم الله خيرا .سمعتك تتكلم عربي هل يمكن تكون استاذي.شرحك راءع
boa tarde sou do brasil gostaria de saber se posso subistitui esse ipm scm1246mkf por scm1246 mf
boa noite irmão. muito bem-vindo, não há folha de dados disponível scm1246mkf, então não tenho certeza sobre a diferença entre scm1246mkf e scm1246 mf. por esse motivo não posso dizer exatamente. mas acho que ambos funcionarão da mesma forma
hi sir can you explain 15V 2A bench power supply working i need convert this power supply 25V 5A but i dont know plz can you help me
Grazie. 🙏👍
Well done
thanks a lot
sir my 24v dc adapter outputn only 21v dc Guid me please
thanks sir ji....
Most welcome
Allah razı olsun.
Thanks ...sir ji...
What starts desoldering item ?
i cannot understand question clearly
can you please explain your question in some detail so that i can reply correctly
@@HaseebElectronics desoldering item is working spontanely. It doesn't have any buton as seen. Is it continously vaccuming ? Or is there any buttun ? Or any other way?
@karisikpekmez6850 it has a push button on grip.
Its desoldering nozzle heats up
We place nozzle on desoldering point
When solder melts
Then the push button on grip is pressed. Its vacuum pump starts and complets its process
@@HaseebElectronics can you show the button detail ?
May be a short video consist of the details of this devices. Even the inner.
@karisikpekmez6850 ua-cam.com/video/0Uvtm64lijs/v-deo.htmlsi=UeCGiPVJGA9HlX25
سلام عليكم هل ممكن تشرح بالعربية شكرا لك
وعليكم السلام
أخي، من الصعب جدًا بالنسبة لي أن أتحدث باللغة العربية لأنني من باكستان. أنا أتكلم العربية قليلا. لكني أقوم بإضافة ترجمات إلى مقاطع الفيديو الخاصة بي، يمكنك تشغيل الترجمات بالضغط على زر CC الموجود على شاشة الفيديو على هاتفك واختيار الترجمة العربية
أطيب التحيات والشكر الخاص
Sir apka disoldar tool Weller wr3m price?
complete set with all accessories is above 3000+ USD
@@HaseebElectronics o my good 330750 BDT
Sir muja ek oscilloscope chiya best konsa hoga? Hds242s model?
Hello brother Haseeb please where are you location
i am in Jordan, please
Anyone please help...
mashallah
😊😊😊
best regards
Students and hobbyist would not have the budget for these expensive vacuum pumps, just mask off the board and use a solder sucker as an economical alternative.
That Weller is over $2,000 !
yes
WELLER WR3M complete set is around $3000+
👍
Please Urdu cha
yes brother
sure i will do it soon
💯❤