Thanks! I replaced the pack, but it was set for a spa with a circ. pump, and I didn't have one. I was able to program in the correct LL3 and it worked fine.
Your video was very helpful. Holding down the pump button for 30 seconds then pressing the light button reset my spa, same control panel as you have. Thank you!
Hi Ryan, Thanks for all your tips! I wonder if you can help? I had a tree that fell on my electrique lign and broke it...so since that event, my spa won't start! Like there's no électricity at all. I checked the fuses wich seems ok, all breakers on and the spa technicians are way expensive here in Québec. Do you have any tips?
If there's no electricity at all (use a voltmeter to check the incoming lines) then you need to trace back the power line. There's likely an on/off breaker for your hot tub that's nearby. If there's power coming in but the control panel isn't registering anything, then you're probably best getting a new control board.
How do you know which LL program to run? I have changed my heater because of FLO code. Still same problem. Iam wondering if it's the LL program. I had it on 1. Pump 1 wouldn't turn off. I now have it on 4 now I can individually turn on and off each pump.
There's a piece of paper that comes with your pump that explains what the different LL values are. Watch out! They're different even for the same model but different software versions they've loaded on the control board.
Every once in awhile I go out to my tub and the jets that are suppose to always be running, pushing flow towards my filters, are not running. I turn off the power and they start up again. I read that they are alway suppose to be running. What would cause this, it’s not my filters I took them out and replaced them
I drained and cleaned my hot tub and everything worked fine. 2 days later I get the flo error and only one side of hot tub is working. Any suggestions?
Thank you for taking the time to document your repair. I learned a lot from it.
You gave more information on these silly packs over any dealer or tech online.
Thanks! I replaced the pack, but it was set for a spa with a circ. pump, and I didn't have one. I was able to program in the correct LL3 and it worked fine.
Your video was very helpful. Holding down the pump button for 30 seconds then pressing the light button reset my spa, same control panel as you have. Thank you!
Glad it helped! Thank you for letting me know.
Thanks!! I have a diff control panel but I managed to change the LL code from 4 to 5, then set it back to 4. It fixed the heating issue I had.
how did you change the LL code?
@@sethscofield That's explained in this video. Basically hold the Pump 1 button down for 30 seconds.
😃 9:51 Neighbor's Yard 😃
Where pump one is plugged into the Orange connector. How do you remove the plug I cannot get it out of the Orange connector?
Press down the tab at the top and wiggle it free.
Hi Ryan, Thanks for all your tips! I wonder if you can help? I had a tree that fell on my electrique lign and broke it...so since that event, my spa won't start! Like there's no électricity at all. I checked the fuses wich seems ok, all breakers on and the spa technicians are way expensive here in Québec. Do you have any tips?
If there's no electricity at all (use a voltmeter to check the incoming lines) then you need to trace back the power line. There's likely an on/off breaker for your hot tub that's nearby. If there's power coming in but the control panel isn't registering anything, then you're probably best getting a new control board.
Thank You!
Wrench symbol and 3 dotted lines flashing in right top corner??? Same control panel same hot tub
How do you know which LL program to run? I have changed my heater because of FLO code. Still same problem. Iam wondering if it's the LL program. I had it on 1. Pump 1 wouldn't turn off. I now have it on 4 now I can individually turn on and off each pump.
There's a piece of paper that comes with your pump that explains what the different LL values are. Watch out! They're different even for the same model but different software versions they've loaded on the control board.
Every once in awhile I go out to my tub and the jets that are suppose to always be running, pushing flow towards my filters, are not running. I turn off the power and they start up again. I read that they are alway suppose to be running. What would cause this, it’s not my filters I took them out and replaced them
No motor should ever be running all the time, 24 hours a day. It's neither economical nor good for the motor.
I drained and cleaned my hot tub and everything worked fine. 2 days later I get the flo error and only one side of hot tub is working. Any suggestions?
Replace Flo Sensor and remove all air from the system...bleed the system
@@1Patient Yup. This! See the part about the red hoses that help bleed the system.