M Machine Controller

Поділитися
Вставка
  • Опубліковано 17 гру 2024

КОМЕНТАРІ • 20

  • @Nclk619
    @Nclk619 5 місяців тому

    I just bought a used twmx and this video is amazing. Much better than any manual. I wish you would have more videos like this. Thank you so very much!

  • @sandrak.7279
    @sandrak.7279 2 роки тому +3

    Thank you so much for this tutorial!! There is no information out there on this machine with this control panel.

    • @morenom619
      @morenom619 Рік тому

      a young lady had an imformative video on youtube. have you seen any other videos similar

  • @dvalencia124
    @dvalencia124 2 роки тому +1

    Very Informative. Thank you for sharing!

  • @paddypravda839
    @paddypravda839 4 роки тому +1

    Thanks for the upload. Very helpful.

  • @northwestgraphicworks7424
    @northwestgraphicworks7424 Рік тому

    I have a Tajima TFMX-IIC1502. I have the same M Controller Panel. Question is how do I change needle positions. Currently the it's on needle 2 and I want to have it on needle 1 for centering my hoop. Thanks, Mark

  • @doronazriel2920
    @doronazriel2920 9 місяців тому

    I have a Tajima c1510 and I don't know how to set the rim size for the machine. Is there an instructional video for this?

  • @murern7117
    @murern7117 3 роки тому +1

    Did anyone get any help here?
    I have a 2007 TFXM c-1501 that will not start after I replaced the battery in the control box.
    I think need to install a new firmware and do not know how to do it. My machine has both floppy disk and usb. Floppy on the side, and usb on the back.
    It sais floppy disk fail (40) and CMOS checksum error on the screen and stops there when I turn it on. Can anybody please help me with this?
    I’m from Norway, and the nearest dealer/support is over 1000km away.

  • @FISHONOVERLAND
    @FISHONOVERLAND 3 роки тому

    Nice video 👊

  • @mdsalimmia2233
    @mdsalimmia2233 Рік тому

    thank you for sharing

  • @alejandrotorresrey9773
    @alejandrotorresrey9773 2 роки тому +1

    Alguien sabe como prender las luces led?

  • @signking
    @signking 2 роки тому

    hey boss how do you update the software on this?

  • @kzellss4491
    @kzellss4491 3 роки тому

    Does any one know to fix a error x - driver irregular signal x-axis driver signal, detected ?

  • @arielevelin7181
    @arielevelin7181 2 роки тому

    Hi there, my dad has the same machine but it is stuck on the startup screen that says windows. Do you know what he can press to get it to function?

    • @gregdede9855
      @gregdede9855 Рік тому

      cpu is not working anymore u need upgrade for x21 type

    • @positivefix
      @positivefix Рік тому

      Sounds like the Windows installation is corrupt. I am assuming its Windows XP, you could try running an install repair from a USB drive, if that fails then perhaps re-installing windows from a USB drive would work, however do not do a fresh install as this will overwrite the software to control the machine.
      If you have the control software available or if you can get a copy from the manufacturer then do a fresh install and then re-install the control software.

  • @heddizemmouri1583
    @heddizemmouri1583 2 роки тому

    Bonsoir svp vous avez cette vidéo en français c urgent c pour faire des applique

  • @AnsarAli7a
    @AnsarAli7a 2 роки тому

    Good bro

  • @markusangula7503
    @markusangula7503 6 років тому

    MY MACHINE IS ONLY SELLECTING ONE COLOUR

  • @sangampal2570
    @sangampal2570 3 роки тому

    Hindi me batro