Hi I might need your help again😁 on my ford focus 2.0 tdci engine, could you please tell me where is the ignition wire is located at the enginebay? I would like to install drl led lights and connect it to my ignition wire to turn it on. Thank you for time.
Wydaje mi się że lepiej jest wylać całe paliwo z pojemnika wstawić nowy filtr zakręcić i tłoczyć paliwo strzykawką wlotem dolotowym paliwa aż zacznie się przelewać wylotowym i dopiero zamontować węże
+Saakaszwili czasem w tym silniku występuje pompka w baku - wtedy odpowietrzenie w ogóle nie jest problemem. Można też podłączyć węże do filtra, potem odpiąć wężyk powrotny z pompcy wysokiego ciśnienia do baku i sprężonym powietrzem dmuchać do baku przez ten wąż. Wtedy powietrze przepcha paliwo przez cały układ.
Does this assembly have any means of removing filtered out water? Ie more traditional type fuel filter housings have a valve/tap at the bottom to drain out water. Thanks
s, yes there is a drain nipple at the bottom of the filter housing, but he did not bother using it and left some fuel in the bottom of the housing, this is just one of the mistakes he made, he obviously is not aware that this lower section of the filter housing is there to collect water and other debris from the fuel as it passes through.
Same problem here the plastic head just rounded off. Tried heating with heat gun and packed the sides with aluminium tape. Got it to move 1/16 turn and then was totally stuck again. Not sure how to get it off now?! Got
You have just demonstrated how little you know about changing a fuel filter correctly, first take those filthy gloves off and put some clean ones on, and before fitting the new filter you should have cleaned out the lower section of the filter housing, this lower section of the housing is there to collect water and other debris from the fuel as it passes through.
Hi, I was trying to do mine earlier but the fuel filter top will not unscrew and as its plastic its starting to round off. Any tips how I can get it to loosen please? looks so easy in the video, typical :(
I've got a Ford Mondeo 2012 MK4 Diesel 2L and the fuel filter is at the rear of the car, not in the engine bay. This video is correct for mine: ua-cam.com/video/Po4BddwSJ1Q/v-deo.html
Yes I agree with the comment below regarding woolen gloves, the fibres could block or restrict the diesel flow, Mmmm .
Please make a list of tools needed. Size and torque
What size is the socket you use to unscrew the filter cover? Thanks!
27. I tried 26 but 27 was better.
Thanks for the video. I have manage to change it. Its definitely a go for.
Keep up to great work on the videos
Hi, mr-fix, can you tell me where are the heaters or glow plugs.
Thanks :)
Engine glow plugs are at the back of the engine. You would have to remove EGR with the EGR cooler to access them.
@@mrfixpl Thanks bro!!!!
Brilliant video gave me the confidence to do it myself!! Thanks
Witam,czu pęcherzyki powietrza w przewodzie z filtra do pompy to norma ,czy gdzies jest nieszczelnosc?
Skoro jest powietrze, to jest nieszczelność.
wait, what about how to prime system? any tip please?
+No Way there's next video about that: ua-cam.com/video/KdoE6-QmAoo/v-deo.html
+mr-fix could you be kind enough to tell me where do you get these line plugs that you are using after disconnecting them?
+No Way they came with the fresh filter
Hi
I might need your help again😁
on my ford focus 2.0 tdci engine, could you please tell me where is the ignition wire is located at the enginebay?
I would like to install drl led lights and connect it to my ignition wire to turn it on.
Thank you for time.
Look inside engine bay fuse box. You should find a fuse or relay that's ignition-hot.
mr-fix thanks again. in the fuse box I was able to find anunocupied ACC slot. 🖒
4:06 "Then prime fuel system" - how?
Hi Mr Fix,
I have air bubbles in my fuel line causing the car to be sluggish at low speeds and low revs. Where would the air be getting in at?
Sometimes it's the fuel lines, sometimes the filter body is cracked, sometimes all you need to do is replace a seal on the fuel line.
Do you know how to prime fuel system ?
Try this: ua-cam.com/video/KdoE6-QmAoo/v-deo.html
Wydaje mi się że lepiej jest wylać całe paliwo z pojemnika wstawić nowy filtr zakręcić i tłoczyć paliwo strzykawką wlotem dolotowym paliwa aż zacznie się przelewać wylotowym i dopiero zamontować węże
+Saakaszwili nie trzeba wtłaczać paliwa. przy odpowietrzaniu i tak filtr się napełni.
ostatnio tak zrobiłem i obyło się bez odpowietrzania pęcherzyki powietrza się nie pokazują : )
+Saakaszwili czasem w tym silniku występuje pompka w baku - wtedy odpowietrzenie w ogóle nie jest problemem. Można też podłączyć węże do filtra, potem odpiąć wężyk powrotny z pompcy wysokiego ciśnienia do baku i sprężonym powietrzem dmuchać do baku przez ten wąż. Wtedy powietrze przepcha paliwo przez cały układ.
Does this assembly have any means of removing filtered out water? Ie more traditional type fuel filter housings have a valve/tap at the bottom to drain out water. Thanks
s, yes there is a drain nipple at the bottom of the filter housing, but he did not bother using it and left some fuel in the bottom of the housing, this is just one of the mistakes he made, he obviously is not aware that this lower section of the filter housing is there to collect water and other debris from the fuel as it passes through.
What size is the socket?
So? how do i prime the system? and then? video stops before its all done
My housing is so tight that the plastic where the socket cups onto is being damaged.. any tips on how to help loosen the top of the housing?
I've got a breaker bar and a hollow piece of circle steel pipe for leverage aswell
Same problem here the plastic head just rounded off. Tried heating with heat gun and packed the sides with aluminium tape.
Got it to move 1/16 turn and then was totally stuck again.
Not sure how to get it off now?!
Got
Hi what size is the socket you used
Dont think he wants to answer you .Just measure it with ruler
where do you get those caps from
It was part of the replacement set.
.......and how do you prime the fuel lines. You did not show the whole process. Now I have to look elsewhere😢
I did, in separate video: ua-cam.com/video/KdoE6-QmAoo/v-deo.html
does it make a difference if we actually change the fuel filter
:) thanks Men a just have a problem whit fuel filter
+tom last happy to help!
You have just demonstrated how little you know about changing a fuel filter correctly, first take those filthy gloves off and put some clean ones on, and before fitting the new filter you should have cleaned out the lower section of the filter housing, this lower section of the housing is there to collect water and other debris from the fuel as it passes through.
You showed everything but did not show most important. How to prime the system from air.
I did. In separate video.
super video!👍
+Andris Locmelis
thank you!
Hi, I was trying to do mine earlier but the fuel filter top will not unscrew and as its plastic its starting to round off. Any tips how I can get it to loosen please? looks so easy in the video, typical :(
Baz F Maybe get an oil filter strap around as much of the body as you can.
Luego no arranca.
ua-cam.com/video/KdoE6-QmAoo/v-deo.html
I've got a Ford Mondeo 2012 MK4 Diesel 2L and the fuel filter is at the rear of the car, not in the engine bay. This video is correct for mine: ua-cam.com/video/Po4BddwSJ1Q/v-deo.html
+BenEvolent1988 Great tip. Thanks for your comment!
Didn’t show how to prime
Also forgot to bleed air out
I did in next video.
video is too far dont even know what he's doing