Very good I just got into sand casting and I made sand green sand from a mix of cat litter clumping cat litter that is along with straining fine sand and I would look to forward to maybe using Petra Bond one day for a better finish
Thanks. This confirmed that I was doing the right thing with my K Bond sand. I used Isopropyl Alcohol as the catalyst though. I used it straight too. Can you say why the water is necessary?
Hello, will SAE 10W-30 motor oil work instead of the SAE 30? I have that on hand already, and from what I read the 10W means it will act as a SAE 10 oil at low temperatures, but not sure how that would play into the effectiveness in this use.
I'm not sure about using multi weight oil. I think I would buy some straight 30 weight. You would hate to ruin your petrobond for the cost of some oil. Good luck!
Is that the same oil you would mix with fuel for a 2 stroke engine I’ve been looking at options for casting lead and the moisture in green sand has a risk of causing explosive reactions
No it is regular motor oil, the less additives the better. You want a non detergent if you can get it. Tractor Supply usually sells them. You will have to start with Petrobond sand which you can get on ebay. It has binders in it that you can't buy separately.
Couldn't you mix you 30SAE of 1 ounce and 1/2 ounce of alcohol and a 1/2 ounce of water all together in a small spray bottle? Then mull your sand by hand or with a flour sifter. Spray it,hand mull it and then sift a few times??? I had about 50lbs of Petrobond I bought about 8 years ago and used about 15lb then put it up in the rafters of the shed for storage.It was in a plastic bag then that bag was inside another. Got it down and it seems to still hold but felt a little dry from storing it up there that long. I'd like to get it back to as close to new as 35lbs of the stuff can be pricey and this box full hadn't even been used.
I haven't ever mixed them together and sprayed them on. The alcohol is supposed to act as a catalyst so I would think you would have to mull in the oil first as it would separate in the bottle. Good luck with your sand.
It shows in the video that I added that amount to 35 pounds of sand. It's not real critical because it depends on how depleted your petrobond is. I would start with that amount and add more as needed to get the green strength back. Hope that helps you!
You start with petrobond sand and when it looses it green strength you have to do this process. This is not a video on how to make the molding sand but how to rejuvenate it.
This is petrobond. You can buy it from a guy on ebay. You can not make petrobond at home but you can make Kbond which is very similar, search google you will find the recipe. Thanks for watching!
+davisx2002 There are recipes for Kbond sand which is similar, on the internet, but some of the ingredients are hard to find. You can buy petrobond from a guy on ebay, just search for petrobond sand and he will come up.
Tried many recipes to no avail i was ready bin my petrobond But this technique works like a charm thanks very much for your video
You're welcome. Thank you for taking the time to let me know!!
Very good I just got into sand casting and I made sand green sand from a mix of cat litter clumping cat litter that is along with straining fine sand and I would look to forward to maybe using Petra Bond one day for a better finish
Thanks. Good luck with your castings!
Thanks kindly! Just opened my new bags of Tetrobond to discover they are all dry as Hell! Hope this does the trick to make it usable.
Hope it worked for you!
Do you have a video of how you built your muller?
ok .. thank you so much
wish you all the best
WOW thank you so much!
You're welcome!
Thanks. This confirmed that I was doing the right thing with my K Bond sand. I used Isopropyl Alcohol as the catalyst though. I used it straight too. Can you say why the water is necessary?
I don't know the reasoning that's just the original recipe I was given and it has worked great for me for years. Glad this was a help to you.
Hello, will SAE 10W-30 motor oil work instead of the SAE 30? I have that on hand already, and from what I read the 10W means it will act as a SAE 10 oil at low temperatures, but not sure how that would play into the effectiveness in this use.
I'm not sure about using multi weight oil. I think I would buy some straight 30 weight. You would hate to ruin your petrobond for the cost of some oil. Good luck!
Thank you for putting this together. Do you have anything to add to this process? Where did you get the information on what to add and when?
This is still the way I do it.
I would make a feed tube thar dribbles the oil and alcohol out in front of the wheel.
That would be a good idea. Thanks for watching!
Perhaps use two-stroke oil? Supposedly it will smoke less?
Interesting
@@SoatMon I hope to get some Petrobond in the future, and I hope to use two-stroke oil to rejuvenate it.
Is that the same oil you would mix with fuel for a 2 stroke engine I’ve been looking at options for casting lead and the moisture in green sand has a risk of causing explosive reactions
No it is regular motor oil, the less additives the better. You want a non detergent if you can get it. Tractor Supply usually sells them. You will have to start with Petrobond sand which you can get on ebay. It has binders in it that you can't buy separately.
Couldn't you mix you 30SAE of 1 ounce and 1/2 ounce of alcohol and a 1/2 ounce of water all together in a small spray bottle? Then mull your sand by hand or with a flour sifter. Spray it,hand mull it and then sift a few times??? I had about 50lbs of Petrobond I bought about 8 years ago and used about 15lb then put it up in the rafters of the shed for storage.It was in a plastic bag then that bag was inside another. Got it down and it seems to still hold but felt a little dry from storing it up there that long. I'd like to get it back to as close to new as 35lbs of the stuff can be pricey and this box full hadn't even been used.
I haven't ever mixed them together and sprayed them on. The alcohol is supposed to act as a catalyst so I would think you would have to mull in the oil first as it would separate in the bottle. Good luck with your sand.
What type of sand did you use? Should it be silica sand?
You need to start with Petrobond sand. This will not work with just plain sand.
@SoatMon What kind of sand?
1 oz of oil to how much sand? Sorry if you’ve covered this already.
It shows in the video that I added that amount to 35 pounds of sand. It's not real critical because it depends on how depleted your petrobond is. I would start with that amount and add more as needed to get the green strength back. Hope that helps you!
What does the"catalyst" (alcohol) do for the mixture?
I honestly don't know. I think it kind of gels the oil to make it adhere to the sand better and form a clump when compressed.
How many HP motor are you running on the muller?My next build.
Sorry, I don't really know what it is and I don't have easy access to the plate to check.
Hii
Thanks for video
But i don't get which sand u use before u mix the oil and alcohol?
You start with petrobond sand and when it looses it green strength you have to do this process. This is not a video on how to make the molding sand but how to rejuvenate it.
Hi there ! I am looking for a proper petrobond style recipe ? Any u can share ?
Not that I know of. I buy mine from a guy on eBay and keep it going as in this video. I have had mine for years.
i just wanted to know how i make this kind of sand in my home ..
This is petrobond. You can buy it from a guy on ebay. You can not make petrobond at home but you can make Kbond which is very similar, search google you will find the recipe. Thanks for watching!
how much does this sand cost? or can you make it from scratch?
+davisx2002 There are recipes for Kbond sand which is similar, on the internet, but some of the ingredients are hard to find. You can buy petrobond from a guy on ebay, just search for petrobond sand and he will come up.
thanks mate
hello . nice work . can i ask you ?
What do you want to ask me?